# Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

12 views
Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC supply, D2 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load.

## Related questions

1 answer 19 views

Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

1 answer 24 views

Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform.

1 answer 78 views

In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: (1) 50 Hz (2) 100 Hz (3) 150 Hz (4) 200 Hz

1 answer 16 views

In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: (1) 30 V (2) 60 V (3) 15 V (4) 10 V

1 answer 9 views

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

1 answer 5 views

Draw the block diagram of regulated DC power supply and explain the function of each block.

1 answer 11 views

Draw output characteristics of common emitter [CE] configuration and explain active, saturation and cut-off regions in detail.

1 answer 16 views

With the help of a neat circuit diagram explain the working principle of Digital to Analog converters.(DAC)

0 answers 32 views

With the help of a schematic diagram explain how a overcurrent relay protects a line during short circuit fault.

1 answer 491 views

Explain the principle of ON-OFF control and phase control of AC voltage controller with suitable circuit and waveforms.

1 answer 69 views

With the help of suitable diagram, explain how humidity is measured with dry and wet bulb thermometer.

0 answers 50 views

Explain the leakage flux and its effect with the help of neat diagram.

0 answers 19 views

Explain space vector transformation and space vector switching with the help of diagram. What are the advantages of SVM?

1 answer 12 views

The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is (A) 1200 Hz (B) 600 Hz (C) 100 Hz (D) 50 Hz

1 answer 17 views

In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is   (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V

1 answer 10 views

Draw the circuit diagram of crystal oscillator and explain its working.

1 answer 13 views

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt

1 answer 16 views

With the help of neat diagram, explain the construction of current transformer.

1 answer 38 views

Explain working of 'hot wire anemometer with the help of diagram.

1 answer 70 views

With the help of neat diagram, explain the method to obtain unidirectional polarity in train lighting.

1 answer 8 views

What is solenoid valve ? Explain its working with the help of diagram.

1 answer 9 views

In a full wave rectifier the negative point in a circuit is   (A) cathode (B) anode (C) The central tap on the high voltage secondary (D) plate.

1 answer 39 views

Explain with necessary diagram the earth fault protection of power and auxiliary circuit.

0 answers 54 views

A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load. For a firing angle of 60° for the SCR, the average output voltage is   (a) 240/π (b) 400/π (c) 300/π (d) 200/π

1 answer 10 views

Draw and explain Hartley Oscillator circuit diagram.

1 answer 22 views

If the input to a differentiating circuit is a saw-tooth wave, then output will be …………….. wave: A) square B) rectangular wave C) triangular wave D) rectified sine wave

1 answer 8 views

Draw block diagram of IC 723. Write the functions of IC 723.

1 answer 21 views

Sketch circuit diagram of bridge rectifier with LC filter. State function of each component.

1 answer 31 views

Draw a labeled block diagram of sine wave generator and state function of each block.

1 answer 24 views

Draw and explain the response of first order and second order instruments to the step input.

1 answer 5 views

The transformer utilization factor of full wave bridge rectifier is   (A) 0.812 (B) 0.286 (C) 0.693 (D) 0.782

1 answer 26 views

Draw the diagram of zero crossing detector using op-amp and explain its working.

1 answer 117 views

Draw the diagram and explain the working of ferrodynamic type frequency meter.

1 answer 28 views

Draw the block diagram for PLC power supply and explain the function of each block.

1 answer 13 views

A full adder is a combinational circuit that performs the arithmetic sum of three input bits and produces a (a) sum output (b) sum output and a carry (c) sum output with two carries (d) two sums with two carries

1 answer 20 views

The input frequency of a bridge rectifier is 50 its output frequency will be  1. 25 Hz 2.50 Hz 3.75 Hz 4. 100 Hz

1 answer 205 views

An ac voltmeter using full -wave rectification and having a sinusoidal input has an ac sensitivity equal to  (1) 1.414 times dc sensitivity (2) dc sensitivity (3) 0.9 times dc sensitivity (4) 0.707 times dc sensitivity

1 answer 24 views

State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

1 answer 28 views

Determine the output frequency for a frequency division circuit that contains 12 flip–flops with an input clock frequency of 20.48 MHz: (1) 10.24 kHz (2) 5 kHz (3) 30.24 kHz (4) 15 kHz

0 answers 13 views

The output clock frequency for a frequency division circuit having 11 flipflops with an input clock frequency of 20.48 MHz is : (A) 10.24 kHz (B) 5 kHz (C) 10 kHz (D) 5.12 kHz

1 answer 7 views

Suggest the suitable diode type for rectifier circuit.

1 answer 11 views

Draw and explain analog input module of PLC.

1 answer 6 views

Describe the working principle of photodiode with proper diagram.

1 answer 47 views

Rectification efficiency of a full wave rectifier without filter is nearly equals to:  (1) 51% (2) 61% (3) 71% (4) 81%

1 answer 16 views

Draw and explain power flow diagram of induction motor.

1 answer 27 views

Draw block diagram of microprocessor based centrallized control equipment of energy conservation and explain it.

1 answer 18 views

Draw diagram of class A push-pull amplifier and explain its operation.

1 answer 13 views

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

1 answer 5 views

Draw and explain the control and power diagram for D.C. injection Braking.

1 answer 24 views

When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: (1) Has no offset (2) Approaches to triangular waveshape (3) Is pure sinusoidal (4) Is square wave