16 views
in Electrical Engineering by
When cathode is positive with respect to anode in an SCR, the number of blocked p-n junctions is 

 (a) 1 (b) 2 (c) 3 (d) 4 

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

Related questions

1 answer 6 views

The number of p-n junctions in a thyristor are  A)1 B) 2 C) 3 D) 4

asked May 20, 2018 in Power Electronics by Shimroz123
1 answer 37 views

Which is the positive terminal anode or cathode?

asked Dec 9, 2017 in Power Electronics by Quiz
0 answers 95 views

The SCR would be turned OFF by voltage reversal of applied anode-cathode ac supply frequency of A) 10 kHz B) 10 Hz C) 5 kHz D) 5 Hz 

asked Jun 18, 2018 in Power Electronics by Shimroz123
1 answer 9 views

It is an unidirectional device that blocks the current flow from cathode to anode   (A) SCR (B) PCR (C) VCR (D) DCR

asked May 17, 2018 in Power Electronics by Shimroz123
0 answers 21 views

A resistor connected across the gate and cathode of an SCR in a circuit increases its (A) dv/dt rating (B) Holding current (C) Noise Immunity (D) Turn-off time

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 40 views

What is the difference between an anode and a cathode?

asked Mar 14, 2018 in Electrical Engineering by Quiz
2 answers 63 views

Do electrons flow from the anode to the cathode?

asked Mar 14, 2018 in Electrical Engineering by Quiz
1 answer 8 views

Is an anode positive or negative?

asked Mar 14, 2018 in Electrical Engineering by Quiz
0 answers 41 views

In a Traveling-wave Tube, the velocity of electron beam with respect to the axial velocity of RF field is kept...  A) Lower B) Higher C) Equal D) Any of these

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

A SCR has an anode supply of sine voltage 200V rms, 50 Hz applied through a 100Q resistor and fired at an angle of 60°. Assuming no voltage drop, the rms value of the output voltage is : (A) 89,7 V (B) 126.7 V (C) 166.7 V (D) 288.28 V

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 15 views

If a forward voltage (less than forward breakover voltage) is suddenly applied across anode and cathode of a thyristor, it may result into   (a) Damage to the thyristor (b) Premature triggering of the thyristor because of high dV/dt (c) Reduced holding current of the thyristor (d) All of the above  

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

Which among the following is the equation for the number of independent loops for a network with n nodes and b branches?  (A) n-1 (B) b+n-1 (C) b-n+1 (D) b-n

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

Is the anode or cathode longer in LED ?

asked Dec 9, 2017 in Power Electronics by Quiz
1 answer 15 views

In a PN-junction with open circuit terminal (equilibrium), with P doping higher as compared to N doping (A) N-side depletion region is small as compared to p-side depletion region (B) N-side depletion region is large as compared to p-side depletion region (C) N-side depletion region is same as p-side depletion region (D) Cannot say

asked May 12, 2018 in Physics by Shimroz123
1 answer 33 views

In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in (A) voltage notching (B) harmonic distortion (C) voltage sag (D) voltage swell

asked Apr 28, 2018 in Electronics Engineering by Shimroz123
1 answer 24 views

Buchholz relay is used as a safety device with respect to which of the following? A) Audio transformers B) Oil filled power transformers C) Air core transformer D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

Which of the following is true with respect to a breeder reactor? A) Its conversion ratio is greater than 1  B) It is capable of generating more fissile material than it consumes C) Both A and B  D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

Which of the following is true with respect to Wien Bridge? A) It does not require equal values of R or C  B) It requires that R and C values of all components must be equal C) It requires that all resistors should have equal values D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 95 views
1 answer 14 views

The potential barrier at a P - N junction is due to  1. Majority carriers 2. Minority carriers 3. Both majority and minority carriers 4. Fixed donor and acceptor ions 

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

An inductor is connected in series with SCR to protect it from A) Excessive high voltage B) Excessive high dv/dt C) Excessive high di/dt D) Excessive large forward current 

asked Jun 18, 2018 in Inductor by Shimroz123
0 answers 7 views

Which of the following are available in the depletion layer of a P -N junction diode ? (A) Free mobile electrons only (B) Free mobile holes only (C) Both free mobile electrons and holes (D) Neither free mobile electrons nor holes

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

The number of independent loops for a network with n nodes and b branches is

asked Apr 29, 2018 in Network Analysis by Shimroz123
0 answers 20 views

One of the necessary and sufficient condition for a network function N(s)=p(s)/q(s) to be a transfer function is that  A) The coefficients of the polynomial p(s) and q(s) must be real and those for q(s) must be positive B) Coefficients of p(s) and q(s) must be real and positive C) Coefficients of p(s) must be positive and real but coefficients of q(s) can be negative also D) Degree of p(s) and q(s) may differ by either zero or one only

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 9 views

A neutral atom with an atomic number of five has electrons equal to: A. 1 B. 5 C. none D. depends on the type of atom

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 9 views

An SCR starts conducting with appreciable current when

asked May 15, 2018 in Power Electronics by Shimroz123
1 answer 12 views

When a P - N junction is forward biased  1.only electrons in N-region are injected into P-region 2.only holes in P-region are injected into N-region 3.majority carriers in each region are injected into the other region 4.minority current is reduced to zero 

asked May 13, 2018 in Semiconductor by Shimroz123
0 answers 20 views

When ‘n’ resistances each of value ‘r’ are connected in parallel, then the resultant resistance is ‘x’. When these ‘n’ resistances are connected in series, total resistance is  (A) n2X (B) X/n (C) n2/X (D) nX2

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

Which of the following is TRUE with respect to HVDC transmission line? (A) For a short distance it is economical over HVAC. (B) In HVDC system, harmonics are not generated. (C) Use of HVDC can improve system stability. (D) Less and cheap terminal, equipments are required in HVDC.

asked May 13, 2018 in High voltage engineering by Shimroz123
1 answer 14 views

Which of the following is CORRECT with respect to a LAG-LEAD compensator ? (A) It is similar to PI controller (B) It acts as Band-pass filter (C) It is Second-order system with one zero, and two poles (D) It acts as a Band-reject filter

asked Apr 25, 2018 in Control System by Shimroz123
0 answers 41 views

If an energy meter disc makes 10 revolutions in 100 seconds when a load of 450W is connected to it, the meter constant in revolutions per kWh is  A) 1000 B) 500 C) 1600 D) 800

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

Consider the following statements with respect to a high Q, series RLC circuit under resonance 1. The voltage across R is equal to the applied voltage 2. The voltage across L and C are zero 3. The voltage across L and C are equal in magnitude 4. The voltage accross L and C are maximum Which of these statements are correct?

asked May 24, 2018 in Electrical Engineering by Shimroz123
1 answer 7 views

Consider the following statements with respect to Discrete Fourier Transform (DFT) : 1. It is obtained by performing a sampling operation in the time domain. 2. It transforms a finite duration sequence into a discrete frequency spectrum. 3. It is obtained by performing a sampling operation in both time and frequency domains. Which of the above statements is/are correct ? (a) 1 and 2 only (b) 2 and 3 only (c) 1 only (d) 3 only

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 32 views

The threshold voltage of an n- channel enhancement mode MOSFET is 0.5V when the device is biased at a gate voltage of 3V. Pinch off would be occurs at a drain voltage of (A) 1.5V (B) 2.5V (C) 3.5V (D) 4.5V

asked Apr 28, 2018 in Power Electronics by Shimroz123
1 answer 322 views

in a three-phase induction motor, the rotor field runs at the following speed with respect to the stator structure: 

asked May 22, 2018 in Induction Machine by Shimroz123
0 answers 6 views

In a network, if the number of holes is n and number of elements is e, then the number of independent mesh equations required to solve the network is (a) e – n + 1 (b) e + n + 1 (c) e + n – 1 (d) e – n – 1

asked May 25, 2018 in Node and mesh analysis by Shimroz123
1 answer 20 views

 If the number of branches in a network is 'B', the number of nodes is 'N' and the number of dependent loops is 'L', then the number of independent node equations will be  (a) N+L–1 (b) B–1 (c) B–N (d) N–1 

asked May 13, 2018 in Network Analysis by Shimroz123
1 answer 24 views

A binary tree T has n leaf nodes. The number of nodes of degree 2 in T is  A) log2n B) n-1 C) n D) 2n

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 10 views

If the number of conditions in a decision table is n, the maximum number of rules (columns) possible is  A) n B) 2n C) 2n D) log2n

asked Apr 11, 2018 in Computer Engineering by Shimroz123
0 answers 8 views

For an SCR with turn-on time of 5 microsecond, an ideal trigger pulse should have   (a) short rise time with pulse width = 3 µsec (b) long rise time with pulse width = 6 µsec (c) short rise time with pulse width = 6 µsec (d) None of the above 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 37 views

In an n-bus power system, considering n-nodes network, the size of ybus is   (a) (n – 1) × (n – 1) (b) (n + 1) × (n + 1) (c) n × n (d) 2n × 2n 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

When does the Body bias effect occur in an n-channel MOSFET?  A) When the Source voltage is less the Bulk voltage B) When the Source voltage is equal to or greater the Bulk voltage C) When the Drain voltage is equal to the Bulk voltage D) When the Gate voltage is equal to the Bulk Voltage 

asked Jun 18, 2018 in MOSFET by Shimroz123
1 answer 14 views

The capacitance of reverse biased P-N junction  1. Decreases with increasing the reverse bias 2. Increases with increasing the reverse bias 3. Depends only on reverse saturation current 4. Makes the P-N junction more effective at high frequencies 

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

Turn-on time of an SCR in series with RL circuit can be reduced by   (a) Increasing circuit resistance R (b) Decreasing R (c) Increasing circuit inductance L (d) Decreasing L 

asked May 13, 2018 in Power Electronics by Shimroz123
0 answers 18 views

When the SCR conducts, the forward voltage drop will   (a) 0.7 V at all load current (b) 2 to 2.5 V at all load current (c) increases slightly with load current (d) remains constant with load current 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 65 views

What happens to the angle between current and voltage, when a small capacitance is added in series with a highly inductive circuit?  (A) Increases (B) Remains same as earlier angle (C) Decreases (D) Becomes indeterminant

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

Define cathode and anode.

asked Sep 3, 2018 by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,514 questions

7,113 answers

135 comments

3,090 users

...