11 views
in Electrical Engineering by
The simplest method of measuring low resistance is the _____________________method. A. Kelvin Bridge B. Wheatstone Bridge C. Voltmeter and Ammeter D. Ohm’s Law 

1 Answer

0 votes
by

The simplest method of measuring low resistance is the Voltmeter and Ammeter method.

Related questions

1 answer 21 views

Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

asked Sep 6, 2018 by Shimroz123
1 answer 17 views

Name the method used to measure following resistances:- (i) Low resistance (ii) Medium resistance (iii) Insulation resistance (iv) Earth resistance.

asked Sep 6, 2018 by Shimroz123
0 answers 18 views

While measuring power in a three phase load by two wattmeter method, the reading of two wattmeter are equal and opposite, when (a) load is balanced (b) power factor is unity (c) phase angle is between 60° to 90° (d) the load is purely inductive 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 18 views

Armature shunting method of speed control of dc shunt motor is preferred over annature resistance method due to:  (1) Better speed regulation (2) Less loss in external resistance (3) Simplicity in control circuit (4) Reduced cost of controller

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

asked Sep 6, 2018 by Shimroz123
0 answers 22 views

For measurement of low resistance, the bridge used is (a) Wheatstone (b) Kelvin (c) Maxwell (d) Anderson

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 13 views

Which of the following is not a method of resistance measurement ? (a) Ammeter – Voltmeter method (b) Post – Office box method (c) Ohm – Meter method (d) Two wattmeter method 

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 27 views

Which method can be used for absolute measurement of resistance? A. Ohm's law method B. Wheatstone bridge method C. Both A & B D. None of these. 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially short circuited because  (A) Cables have a low value of capacitance which draws a high value of charging current (B) Cables have a low value of initial resistance (C) Cables have a high value of capacitance which draws a high value of charging current (D) Cables have a low value of capacitance and initial resistance

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 20 views

The substances which have a large number of free electrons and offer a low resistance are called?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 23 views

When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a low resistance initially and then slowly came to infinity position. This shows that capacitor is ?

asked Mar 21, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 36 views

The function of input attenuators in measuring instruments, like VTVM and CRO, is to (a) Increase the input impedance (b) Attenuate the frequency range (c) Attenuate the input signal amplitude without altering the frequency contents (d) Attenuate the input impedance

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

For measuring the frequency of an unknown A.C. source. Which of the following device is necessary to obtain a standard waveform?  (A) Operational amplifier (B) Astable multivibrator (C) Schmitt trigger (D) Monostable multivibrator

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

Explain V- I method of measurement of medium resistance. 

asked Sep 6, 2018 by Shimroz123
1 answer 9 views

State the range for low and medium resistance.

asked Sep 6, 2018 by Shimroz123
1 answer 19 views

Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

asked May 8, 2018 in Electrical Engineering by Zeeshan
0 answers 15 views

The phenomenon of squirrel cage motors sometimes showing tendency to run at very low speed is known as (1) Cogging (2) Crawling (3) Damping (4) Skewing

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

At low values of slip, the torque of an induction motor is   (a) directly proportional to the square of the slip. (b) inversely proportional to the square of the slip. (c) directly proportional to the slip. (d) inversely proportional to the slip. 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 14 views

Which of the following is a low efficient light source?  A) CFL B) HPSV Lamp C) LPMV Lamp D) Tungsten Lamp

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

The convergence characteristic of the Newton—Raphson method for solving a load flow problem is (A) quadratic (B) linear (C) geometric (D) cubic 

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
0 answers 9 views

One of the most powerful tool for dealing with unbalanced polyphase circuit is the method of symmetrical components introduced by the scientist (a) Gauss (b) Volta (c) Newton (d) C.L. Fortescue

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

The method of speed control used for increasing the speed of a dc shunt motor above its rated speed is  1) armature resistance control 2) field control (3) armature voltage control (4) series parallel control 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

The method suitable for heating of a conducting medium is   (a) Induction heating (b) Indirect arc heating (c) Eddy current heating (d) Resistance heating

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 59 views

The nodal method of circuit analysis is based on  (A) KVL and ohms law (B) KVL and KCL (C) KCL and ohms law (D) Thevenins theorem

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 30 views

In the solution of load flow equation, Newton Raphson (NR) method is superior to the GaussSeidal (GS) Method, because the:  (A) Convergence characteristic of the NR methods are not affected by selection of slack bus (B) Number of iterations required in the NR method is not independent of the size of the system (C) Time ... the NR method is less when compared to the GS method (D) Number of iteration required in the NR method is more than compared to that in the GS method 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views
0 answers 21 views

An electrodynamic wattmeter is not considered suitable for low power factor circuits because of (A) Inductance of voltage coil (B) Reactance of current coil (C) Power loss in voltage coil (D) Power loss in current coil

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 9 views

Cost of low voltage capacitor /kVAr is (1) More than cost of high voltage capacitor/kVAr (2) Is independent of voltage level (3) Less than cost of high voltage capacitor/kVAr (4) Is function of size of capacitor 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 23 views

Voltage control method employed for speed control of induction motors is most effective for (a) A constant torque load only (b) fan type load only (c) for traction load only (d) none of the above

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

Which method is not used for conversion of AC to DC? A. Motor-generator set B. Rotary converter C. Metal rectifiers D. Dynamometers

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

If MN/MX is low the 8086 operates in  ______ mode.   (a) Minimum (b) Maximum (c) Minimum & Maximum (d) Medium 

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

The most suitable motor for low power applications is a/an:  (A) dc series motor (B) dc shunt motor (C) ac two-phase induction motor (D) ac series motor

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

In two -wattmeter method of power measurement, if one wattmeter shows negative reading, then the power factor of the circuit is treated as (A) Unity (B) Lagging (C) Leading (D) Zero

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

In the measurement of three phase power by two wattmeter method, if the two wattmeter readings are equal then power factor of the circuit is  (A) 0.8 lag (B) Unity (C) 0.8 lead (D) Zero 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 24 views

_______ electric power is the most common method used by electrical grids to transfer power.  (A) One-phase (B) Two-phase (C) Three-phase (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 73 views

The self GMD method is used to evaluate

asked May 3, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

Two wattmeter method is employed to measure power in a 3 -phase balanced system with the current coil connected in the A and C lines. The phase sequence is ABC. If the wattmeter with its current coil in A -phase line reads zero, then the power factor of the 3 -phase load will be

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

The material of hair spring used in measuring instruments is made of which of material of the following : (a) Copper (b) Bronze (c) Alnico (d) None of these

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 17 views

Which one of the following frequency meter is suitable for measuring radio frequency?   (a) Vibrating reed frequency meter (b) Weston frequency meter (c) Electrical resonance frequency meter (d) Heterodyne frequency meter 

asked May 13, 2018 in Instrumentation and control by Shimroz123
1 answer 33 views
1 answer 11 views

Electrostatic voltmeters are particularly suitable for measuring high voltages because the construction is simplified due to

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
0 answers 49 views

A high-pass filter has a resistance R = 2 kΩ The lowest input frequency to be passed is 7.5 kHz. The value of suitable coupling capacitor must be: A) 0.001 pico Farad B) 0.01 pico Farad C) 0.1 pico Farad D) 1 pico Farad

asked Jun 4, 2018 in Electrical Engineering by Shimroz123
1 answer 9 views

The resistance value of a carbon resistor having Orange, Red, Brown and Golden color bands is

asked May 14, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...