# The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : -

30 views
The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - a) 225 MHz b) 1.06 MHz c) 10 KHz d) 10 MHz

The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - 10 KHz

## Related questions

A series RLC circuit has a resonant frequency of 1 KHz and a quality factor Q = 100. If each of the R,L and C is doubled from its original value, the new Q of the circuit is:  (1) 25 (2) 50 (3) 100 (4) 200

A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz. (A) 50000 (B) 0.2 (C) 600 (D) 5

In a series RLC high Q circuit, the current peaks at a frequency  (1) equal to the resonant frequency (2) greater than the resonant frequency (3) less than the resonant frequency (4) equal to half the resonant frequency

In an RLC series AC circuit, if frequency is below the resonant frequency, then (a) XC = XL (b) XC < XL (c) XC > XL (d) None of these

In a series RLC circuit that is operating above the resonant frequency, the current : -  a) lags the applied voltage b) leads the applied voltage c) is in phase with the applied voltage d) is zero

For a resonant circuit with resonant frequency of 1 MHz a, 0 = 50 and R = 400, find the value of C (A) 250 pF (B) 1000 pF (C) 1.25 pF (D) 500 pF

In a series RLC circuit operating below the resonant frequency the current  (a) I leads Vs (b) I lags Vs (c) I is in Phase with Vs (d) None of these

An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave amplitude is (a) 8V (b) 4.82 V (c) 2.02 V (d) 1.592 V

In a series L-C circuit at the resonant frequency the?

Consider the following statements with respect to a high Q, series RLC circuit under resonance 1. The voltage across R is equal to the applied voltage 2. The voltage across L and C are zero 3. The voltage across L and C are equal in magnitude 4. The voltage accross L and C are maximum Which of these statements are correct?

For an RLC series AC circuit, the current at series resistance is (a) maximum at lagging power factor (b) maximum at leading power factor (c) maximum at unity power factor (d) minimum at unity power factor

An inductor of Q factor 10 is connected in series with a capacitor having a Q factor of 100. The overall Q factor of the circuit is :  (A) 100/11 (B) 11/100 (C) 110 (D) 1000

For a series resonant circuit, at the half power points,which of the following is true?  (a) Current is half of the current at resonance. (b) Resistance is equal to the reactance. (c) The impedance is half the impedance at the resonance. (d) None of the above

The effective resistance of a coil at high frequency is more than its de resistance on account of : -  a) Skin effect b) Proximity effects c) Eddy current losses d) All the above

A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is

In a series RLC circuit at resonance, the magnitude of the voltage developed across the capacitor  A) Is always zero B) Can never be greater than the input voltage C) Can be greater than the input voltage, however, it is 90° out of phase with the input voltage D) Can be greater than the input voltage, and is in phase with the input voltage

In a series RLC circuit at resonance, which of the following quantities attains maximum value ? (A) Current (B) Voltage (C) Power (D) None of the above

A series RLC circuit resonate at 200 Hz. If the capacitance is increased to four times, the circuit will be in resonance at   (a) 100 Hz (b) 200 Hz (c) 400 Hz (d) 800 Hz

In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?

In a series RLC circuit, which one does not change with change in input frequency ? (A) Bandwidth (B) Quality factor (C) Resonant frequency (D) All of them

Consider the following statements : If a high Q parallel resonant circuit is loaded with a resistance  1. The circuit impedance reduces.  2. The resonant frequency remains the same.  3. The bandwidth reduces.  Which of the above statements is/are correct ?

In a series resonant circuit, maximum voltage across L occurs at  (a) Resonant frequency (b) Slightly below resonant frequency (c) Slightly above resonant frequency (d) At a frequency where I is maximum

The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz

In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C?

In a series resonant circuit, the impedance of the circuit is?

In a series RLC circuit, the rms value of voltage across the resistor is 30 V, across the inductor is 60 V and across the capacitor is 20 V. The rms supply voltage would be (A) 110 V (B) 10 V (C) 220 V (D) 50 V

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current? A. 30 A/s B. 20 A/s C. 10 A/s D. none of these

A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly

What is the pitch factor of a 4 pole alternator having 36 slots and a coil span of 1 to 8?  (A) 140° (B) 80° (C) 20° (D) 40°

A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

The connected load of a consumer is 2 kW and his maximum demand is 1.5 kW. The load factor of the consumer is (a) 0.375 (b) 0.75 (c) 1.33 (d) None of these

A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is

The loop transfer of a system is G(s) H(s) = 5/(s+1) (2s+1)(3s+1) which has the phase crossover frequency fc = 0.16 Hz. The gain margin (dB) of the system is  (a) 6 (b) 4 (c) 2 (d) 0

What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp? (A) 5000 amp (B) 1000 amp (C) 400 amp (D) 800 amp

If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

An RLC series. circuit remains predominantly inductive

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A

A commutator with a diameter of 50 cm rotates at 1000 r.p.m. If brush width is 1.5 cm, the time of commutation will be (a) 0.168 m sec (b) 0.374 m sec (c) 0.481 m sec (d) 0.573 m sec

The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be  (A) 48.0% (B) 57.1% (C) 59.2% (D) 88.8%

The gain of a parabolic dish antenna of 1 m diameter -and 80% efficiency at 9.5 GHz is: a. 39 dB b. 78 dB c. 40 dB d. 45 dB

Consider the following statements  1) The compensating coil of a low power factor wattmeter compensates the effect of the impedance of the current coil ii) The compensating coil of a low power factor wattmeter compensates the effect of the impedance of the voltage coil circuit  A) (i) is true but (ii) is false B) (i) is false but (ii) is true C) Both (i) and (ii) are true D) Both (i) and (ii) are false

A 150 kW electric motor has an efficiency of 92 %, when it operates at full load. Calculate the losses in the machine.  (A) 92 kW (B) 150 kW (C) 163 kW (D) 13 kW

A series RLC circuit has a resistance of 50 , inductance of 0.4H and a capacitor of 10µF. The circuit is connected across a 100V supply. The resonance frequency and the current through the resistance are

In the case of a 70–MHz IF carrier for a transponder bandwidth of 36 MHz, energy must lie between MHz: (1) 34 and 106 (2) 52 and 88 (3) 106 and 142 (4) 34 and 142