Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc. Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it, Please login or register to continue.

Can you help by answering this question?

Super conducting materials can be used for

44 views
in Instrumentation and control by
A zero -level detector is a - a) comparator with a sine wave output b) comparator with a trip point referenced to zero c) peak detector d) limiter

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.

1 Answer

0 votes
by

A zero -level detector is a - comparator with a trip point referenced to zero

Related questions

1 answer 6 views

In a ratio detector: -  a) the linearity is worse than in a phase discriminator b) stabilization against signal strength variation is provided c) the output is twice that obtainable from a similar phase discriminator d) the circuit is the same as in a discriminator, except that the diode are reversed

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
3 answers 50 views

Describe working principle of ultrasonic level detector with diagram.

asked Sep 9, 2018 by Shimroz123
1 answer 26 views

Draw the diagram of zero crossing detector using op-amp and explain its working.

asked Sep 12, 2018 by Shimroz123
1 answer 17 views

The input to a coherent detector is DSB-SC signal plus noise. The noise at the detector output is:  (1) The in-phase component (2) The quadrature-component (3) Zero (4) The envelope

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 17 views

Positive feedback is used in 1. Amplifier 2. Rectifier 3.Oscillator 4. Detector 

asked May 13, 2018 in Electronics Engineering by Shimroz123
0 answers 167 views

Error detector is also called as  (A) Multiplexer (B) Decoder (C) Comparator (D) Integrator

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the transmission bit rate is

asked May 23, 2018 in Electronics communication by Shimroz123
1 answer 22 views

A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______ A) DC voltage restorer B) Clamping circuit C) Both A and B D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
0 answers 12 views

In a clipper circuit with silicon diode and bias of V volts, the clipping level is (a) 0.7 V (c) V (b) V + 0.7 (d) 2V + 0.7

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

An alternator is connected to a bus. For a symmetrical fault at the bus, the fault level is 60 MVA. If another alternator is connected to the same bus, the new fault level will be (1) 120 MVA (2) 60 MVA (3) 30 MVA (4) 15 MVA 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 9 views

In a junction transistor, the doping level of collector region is:  (1) Higher than emitter region (2) Lower than base region (3) Is higher than base region but lower than emitter region  (4) Independent of the doping of base and emitter regions.

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views
1 answer 15 views

 One out of the following statements is not true: A) The curl of gradient of any scalar field is identically zero B) The divergence of curl of any vector field is identically zero C) A field, which has zero divergence, is said to be solenoidal D) A field, whose curl is zero, is said to be rotational 

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

 A power system is subjected to a fault which makes the zero sequence component of current equal to zero. The nature of fault current is: A) Double line to ground fault B) Line to line fault C) Line to ground fault D) Three-phase to ground fault

asked Jun 4, 2018 in Power system by Shimroz123
0 answers 70 views

The power in a 3-phase load is measured by two watt meters. If one watt meter reads zero, then the load power factor is (A) Zero (B) 0.5 (C ) 0.866 (D) unity 

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 46 views

A BJT’s voltage stand-off capability when the base current is zero (A) collector-emitter breakdown voltage (B) minimum collector-emitter voltage (C) collector-base breakdown voltage (D) emitter-base voltage

asked Jun 4, 2018 in Bipolar Junction Transistor by Shimroz123
0 answers 23 views

The output voltage of a battery drops from 100 V with zero load current to 80 V when load current is 2 A. The internal resistance of the battery is (a) 10 Ω (b) 20 Ω (c) 40 Ω (d) 50 Ω

asked May 25, 2018 in Battery by Shimroz123
0 answers 702 views

A system with gain margin close to unity or a phase margin close to zero is (a) conditionally stable (b) relatively stable (c) highly stable (d) highly oscillatory

asked May 25, 2018 in Control System by Shimroz123
0 answers 20 views

The zero sequence current of a generator for line to ground fault is j 2.4 p.u. The current through the neutral during the fault is (a) j 0.8 p.u (b) j 2.4 p.u. (c) j 0.24 p.u. (d) j 7.2 p.u. 

asked May 25, 2018 in Power system by Shimroz123
0 answers 13 views

An induction motor operating at 0.8 pf lagging is consuming 300 kW. A zero real power consuming synchronous motor is connected across the induction motor to raise the pf to 0.92 lagging. The reactive power drawn by the synchronous motor is a. - 352 kVAR b. - 225 kVAR c. - 127.8 kVAR d. - 97.2 kVAR

asked May 24, 2018 in Induction Machine by Shimroz123
1 answer 12 views

A unit step voltage is applied at t = 0 to a series RL circuit with zero initial conditions  A) It is possible for the current to be oscillatory B) The voltage across the resistor at t = 0+ is zero C) The energy stored in the inductor in the steady state is zero D) Theresistor current eventually falls to zero 

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 18 views

A synchronous generator is feeding a zero power factor (lagging) load at rated current. The armature reaction is  (A) magnetizing (B) demagnetizing (C) cross-magnetizing (D) ineffective

asked May 17, 2018 in Synchronous machine by Shimroz123
1 answer 17 views

In a transformer, zero voltage regulation at full load is   (a)Not possible   (b) Possible at unity power factor load   (c) Possible at leading power factor load   (d) Possible at lagging power factor load

asked May 13, 2018 in Transformer by Shimroz123
1 answer 43 views

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

In practice, Earth is chosen as a place of zero electric potential because it 

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: A. 0 V B. 1.2V C. 6V D. 0.6V

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 33 views

A system function has a pole at s=0 and a zero at s= -1. The constant multiplier is unity. For an excitation cos(t), What is the steady-state response?  (A) √2sin(t+450) (B) √2sin(t-450) (C) sin(t-450) (D) Sin(t) 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

When the initial conditions of a system are specified to be zero it implies that the system is?

asked Mar 27, 2018 in Control System by Shimroz123
1 answer 14 views

Draw a diagram of radar level measurement. Write an advantage and disadvantage of it.

asked Sep 9, 2018 by Shimroz123
1 answer 69 views

In a single crystal of an intrinsic semiconductor, the number of free carriers at the Fermi level at room temperature is: A) Half the total number of electrons in the crystal B) Zero C) Half the number of atoms in the crystal D) Half the number of free electrons in the crystal

asked Jun 18, 2018 in Semiconductor by Shimroz123
1 answer 14 views

The amplifiers following the modulated stage in a low level modulation AM system be  (A) linear amplifier (B) harmonic generators (C) class C power amplifiers (D) class untuned amplifiers

asked May 17, 2018 in Amplifier by Shimroz123
1 answer 16 views

An overhead transmission line has a span of 240m between level supports. What is the maximum sag if the conductor weight 727 kg/km and has a breaking strength of 6880 kg? Allow the factor of safety of 2. Neglecting wind and ice loading.

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 19 views

If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of deflection plates is 2 cm, the distance between the plates is 1 cm and accelerating voltage is 500 V, deflection sensitivity is   (a) 33.2 V/cm (b) 0.03 cm/V (c) 66.4 V/cm (d) 0.015 cm/V

asked May 13, 2018 in Instrumentation and control by Shimroz123
1 answer 29 views

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W

asked Apr 25, 2018 in Instrumentation and control by Shimroz123
1 answer 47 views

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

asked Apr 25, 2018 in Instrumentation and control by Shimroz123
1 answer 28 views

What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp? (A) 5000 amp (B) 1000 amp (C) 400 amp (D) 800 amp 

asked Apr 23, 2018 in Instrumentation and control by Shimroz123
1 answer 8 views

Converter is a device for transforming (A) ac to dc (B) dc to dc (C) dc to ac (D) ac to ac

asked Apr 23, 2018 in Instrumentation and control by Shimroz123
1 answer 12 views

The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is (A) 1200 Hz (B) 600 Hz (C) 100 Hz (D) 50 Hz 

asked Apr 23, 2018 in Instrumentation and control by Shimroz123
1 answer 17 views

Intrinsic semiconductor material is characterized by a valence shell of how many electrons? a) 1 b) 2 c) 4 d) 6

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 16 views

The maximum phase lead is contributed by a phase lead network at: - a) mid corner frequency b) lower corner frequency c) upper corner frequency d) phase corner frequency

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 12 views

The polarity of induced voltage while a field is collapsing is : - a) independent of the force creating the field b) opposite to the force creating c) the field identical to the force creating d) the field present only if the force is stationary

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 11 views

The output of an AND gate with three inputs, A, B and C, is HIGH when __________. a) A=1,B=1,C=0 b) A= 0,B= 0,C= 0 ' c) A=1,B=1,C=1 d) A=1,B= 0,C= 1

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 19 views

In a thyristor Latching current is than holding current: - a) equal b) less c) greater d) none of the above

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 11 views

A thermistor is generally a semiconductor material exhibits: a) Positive Temperature co -efficient b) Negative Temperature co -efficient c) Neither positive nor negative temperature co -efficient d) both (a) and (b)

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 30 views

The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - a) 225 MHz b) 1.06 MHz c) 10 KHz d) 10 MHz

asked Apr 14, 2018 in Instrumentation and control by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,560 questions

7,160 answers

135 comments

3,090 users

...