Can you help by answering this question?

What is an electronic controller?

11 views
in Electrical Engineering by
A UJT exhibits negative resistance region : (A) Before the break point (B) Between peak and valley point (C) After the valley point (D) Both (A) and (C)

1 Answer

0 votes
by

A UJT exhibits negative resistance region Between peak and valley point

Related questions

1 answer 44 views

In the emitter characteristic of UJT, the negative resistance portion.  1.lies in the cut-off region 2.continues up to peak point 3.lasts until the valley point is reached 4.does not exist 

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 14 views

Which diode exhibits negative resistance characteristic? (A) LED (B) Zener (C) Tunnel diode (D) PN diode

asked Apr 28, 2018 in Electronics Engineering by Shimroz123
1 answer 9 views

An element is said to have negative resistance when (a) The element has negative temperature coefficient (b) The current / voltage curve has negative slope (c) The element has negative specific resistance (d) The current / voltage curve has a positive slope

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 38 views

 Which of the following is a negative-resistance microwave device for oscillator applications? A) IMPATT Diode B) Gunn Diode C) Snap diode D) Schottky Diode 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 40 views

Which amongst the following has a negative coefficient of temperature for resistance?  a) Copper b) Lead c) Carbon d) Aluminium

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 9 views

In a junction transistor, the doping level of collector region is:  (1) Higher than emitter region (2) Lower than base region (3) Is higher than base region but lower than emitter region  (4) Independent of the doping of base and emitter regions.

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 32 views

The type of power amplifier that exhibits crossover distortion in its output is : (A) Class A (B) Class B (C) Class AB (D) Class C

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 5 views

 UJT has : -  a) two base leads b) one emitter lead c) two emitter leads and one base lead d) one emitter lead and two base leads

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

The transducer with negative temperature co-efficient of resistance is (A) Thermistor (B) Resistance Thermometer (C) Strain Gauge (D) Thermocouple

asked Apr 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 8 views

A UJT can   (A) be triggered by any one of it's three terminals (B) not be triggered (C) be triggered by two of its three terminal only (D) be triggered by all of its terminals only.

asked May 17, 2018 in Power Electronics by Shimroz123
1 answer 17 views

To turn a UJT ON, the forward bias on emitter diode should be:  1. more than the peak point voltage 2. less than the peak point voltage 3. Equal to the peak point voltage 4. Equal to the stand - off voltage  

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 11 views

A thermistor is generally a semiconductor material exhibits: a) Positive Temperature co -efficient b) Negative Temperature co -efficient c) Neither positive nor negative temperature co -efficient d) both (a) and (b)

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 10 views
1 answer 16 views

A conditionally stable system exhibits poor stability at

asked Mar 27, 2018 in Control System by Shimroz123
1 answer 11 views

A negative feedback loop returning a voltage to the input raised the input impedance and making the circuit a better

asked May 23, 2018 in Electrical Engineering by Shimroz123
1 answer 9 views

Susceptibility of a diamagnetic material is 1. Negative 2. Positive 3. Dependent on the temperature 4. Independent of the temperature  Select the correct answer using the codes given below : (a) 1 and 3 only (b) 2 and 3 only (c) 1 and 4 only (d) 2 and 4 only

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 26 views

When a line -to -ground fault occurs, the current in a faulted phase is 100A. The negative sequence current in this case will be : (A) Zero (B) 33.3 A (C) 66.6 A (D) 100 A

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 188 views

A 30 MVA, 13.2 KV synchronous generator has a solidly grounded neutral. Its positive, negative and zero sequence impedances are 0.30, 0.40 and 0.05 pu respectively. What value of reactance must be placed in the generator neutral so that the fault current for a line to ground fault of zero fault impedance shall not exceed the rated line current.  (A) 4.416 ohm (B) 8.8 ohm (C) 2.08 ohm (D) 10.2 ohm 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

What does the region around the stationary electric charge has?  (A) Electric field (B) Magnetic field (C) Semi permeable region (D) Insulating field 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

The region consisting of holes and electrons near the p-n junction of a diode is (A) diffusion region (B) neutral zone (C) recombination region (D) depletion region 

asked Jun 4, 2018 in Diode by Shimroz123
2 answers 19 views

A bipolar junction transistor (BJT) is used as a power control switch by biasing it in the cut-off region (OFF state) or in the saturation region (ON state). In the ON state, for the BJT  (A) both the base-emitter and base-collector junctions are reverse biased (B) the base-emitter junction is reverse ... (C) the base-emitter junction is forward biased, and the base-collector junction is reverse biased (D) both the base-emitter and base-collector junctions are forward biased

asked May 18, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 52 views

Space charge region or depletion region in a P-N diode has (A) No charge (B) No fixed charge (C) No mobile charge (D) Both fixed and mobile charges

asked May 12, 2018 in Semiconductor by Shimroz123
0 answers 18 views

A critical region  (1) is a piece of code which only one process executes at a time (2) is a region prone to deadlock (3) is a piece of code which only a finite number of processes execute (4) is found only in Windows NT operation system

asked Apr 10, 2018 in Computer Engineering by Shimroz123
1 answer 30 views

What is the depletion region of a diode?

asked Jan 5, 2018 in Electronics Engineering by Quiz
1 answer 28 views

Draw and explain the characteristic of UJT. 

asked Sep 5, 2018 by Shimroz123
1 answer 11 views

An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

asked May 20, 2018 in Amplifier by Shimroz123
0 answers 17 views

The transient step response of two systems exhibits same peak time. The dominant poles of the two systems can be represented in s plane along  A) A line parallel to X axis B) A line parallel to Y axis C) A line at an angle to negative real axis D) A semicircle

asked Apr 9, 2018 in Control System by Shimroz123
1 answer 12 views

The negative sign in the expression e = – N (d∅)/dt is due to: (1) The Fleming’s Rule (2) Thumb’s Rule (3) Faraday’s Law (4) Lenz’s Law

asked May 29, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

Systems for Protection from negative sequence current is provided normally for (a) Transformers (c) Transmission lines (b) Generators (d) Motors

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

In two -wattmeter method of power measurement, if one wattmeter shows negative reading, then the power factor of the circuit is treated as (A) Unity (B) Lagging (C) Leading (D) Zero

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

Which of the following can have positive or negative charge? A. Electron B. Iron C. Hole D. Neutron. 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

Which of the following has negative temperature coefficient? A. Brass B. Mercury C. Electrolytes D. Silver. 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 12 views

With the introduction of negative feedback, the gain—bandwidth product of an amplifier  A) Becomes infinity B) Increases C) Decreases D) Remains constant

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

Is an anode positive or negative?

asked Mar 14, 2018 in Electrical Engineering by Quiz
0 answers 14 views

Why does charge flow from positive to negative?

asked Mar 14, 2018 in Electrical Engineering by Quiz
1 answer 23 views

The effect of negative feedback on distortion and bandwidth is A) Both distortion and bandwidth get decreased B) Both distortion and bandwidth get increased C) Distortion is reduced and bandwidth is increased D) Distortion is increased and bandwidth is decreased 

asked Jun 18, 2018 in Control System by Shimroz123
1 answer 21 views

A negative sequence relay is commonly used to protect  (A) an alternator (B) an transformer (C) a transmission line (D) a bus bar

asked May 25, 2018 in Power system by Shimroz123
1 answer 28 views

An amplifier without feedback has a gain of 1000. The gain with a negative feedback of 0.009 is  A) 10 B) 100 C) 125 D) 900

asked May 20, 2018 in Amplifier by Shimroz123
1 answer 14 views

Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will   (A) Amplify the noise as much as the signal (B) Reduce the noise (C) Increase the noise (D) Not effect the noise

asked May 17, 2018 in Amplifier by Shimroz123
1 answer 9 views

In a full wave rectifier the negative point in a circuit is   (A) cathode (B) anode (C) The central tap on the high voltage secondary (D) plate.

asked May 17, 2018 in Power Electronics by Shimroz123
1 answer 34 views

An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is  (1) 141 (2) 92.3 (3) 9.23 (4) 1.41

asked May 1, 2018 in Power Electronics by Shimroz123
1 answer 308 views

In order to regulate steady state error to zero, in a negative feedback control system, one employs

asked May 1, 2018 in Control System by Shimroz123
1 answer 366 views

A negative sequence relay is used for protection of  (1) Generator (3) Motor (2) Transformer (4) Long Transmission lines

asked May 1, 2018 in Switchgear And Protection by Shimroz123
1 answer 27 views

A transformer has negative voltage regulation when its load power factor is   (1) Zero (2) Unity (3) Leading (4) Lagging

asked Apr 30, 2018 in Power system by Shimroz123
1 answer 26 views

A unity negative feedback control system is found to have a gain margin of 20 dB. The Nyquist plot of the system (A) crosses the real axis at +0.1 (B) crosses the real axis at -0.1. (C) crosses the imaginary axis at -0.1 (D) crosses the imaginary axis at +0.1

asked Apr 28, 2018 in Control System by Shimroz123
1 answer 15 views

Negative feedback in a closed-loop control system DOES NOT (A) reduce the overall gain (B) reduce bandwidth (C) improve disturbance rejection (D) reduce sensitivity to parameter variation

asked Apr 26, 2018 in Control System by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...