17 views
in Electrical Engineering by
In an isolated output dc-to-dc fly back converter, the high frequency transformer used works as an inductor (a) during turn -on period of the switching device (b) during turn off period of the switching device (c) during both (d) none of these

Related questions

1 answer 15 views

In practice, a current source inverter consists of an AC/ DC converter with a large inductance ‘L’ in the output. This inductance maintains a ……… …………through the switching devices over short interval of time. A) constant current B) constant voltage C) constant power D) none of the (A), (B), (C)

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
0 answers 86 views

 When The dc converter in figure shown has a resistance load of R = 10 Ω and the input voltage is Vs 220 V the converter switch remains on, its voltage drop is Vo -2 V. The chopping frequency is fI K sW Vs If the duty cycle is 50%, determine: (a) the average output voltage V (b) the RMS output voltage Vo (c) the converter efficiency (d) the effective input resistance of the converter

asked Apr 26 by Hussein
1 answer 16 views

Tachometer works essentially as a generator with output voltage proportional to magnitude of the : - a) Angular Velocity of the shaft b) Torque of the shaft c) Temperature of the shaft d) Back Lash of the shaft

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 25 views

A sine wave voltage is applied across an inductor. When the frequency of the voltage is decreased, the current decreases.

asked Nov 23, 2017 in Electrical Engineering by James
1 answer 7 views

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

asked 6 days ago in Elements of Electronics by Shimroz123
0 answers 87 views

What is back EMF in inductor?

asked Mar 15, 2018 in Electrical Engineering by Quiz
1 answer 24 views

To get minimum harmonic distortion in the output, a 3-Ф to 3-Ф cyclo-converter requires :  (A) 12 SCRs (B) 18 SCRs (C) 36 SCRs (D) 72 SCRs

asked Apr 30, 2018 in Power Electronics by Shimroz123
2 answers 49 views

An Auto-transformer (which has only one winding) may be used as a ______ .  (A) Both Step-Up and Step-Down transformer (B) Step-Down Transformer (C) Step-Up Transformer (D) None of these

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 58 views

An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be  (1) unaffected (2) decreased (3) increased (4) either decreased or increased depending on the direction of the DC field

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 21 views

If the back emf of a dc motor is doubled and its speed is also doubled, the torque developed in the machine will  (1) get doubled (2) become 4 times (3) get halved (4) remain unaltered

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

An inductor at t = 0+ with zero initial conditions acts as   (a) short circuit (b) open circuit (c) current source (d) voltage source 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

As there is no back e.m.f. at the instant of starting a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit?

asked Mar 20, 2018 in Electrical Machine by Shimroz123
0 answers 13 views

Which of the following insulator is used for high frequency applications ? (A) Steatite (B) Forsterite (C) Bakelite (D) Porcelain

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 18 views

The dc motor used for intermittent high torque loads is  (1) dc series motor (2) dc shunt motor (3) differential compound motor (4) cumulative compound motor

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 7 views

The output clock frequency for a frequency division circuit having 11 flipflops with an input clock frequency of 20.48 MHz is : (A) 10.24 kHz (B) 5 kHz (C) 10 kHz (D) 5.12 kHz

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is  (A) 119.05 A (B) 79.37 A (C) 68.73 A (D) 39.68 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 8 views

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

asked May 23, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 54 views

The main function of the transformer used in the output of a power amplifier is  (A) To step up the voltage  (B) to increase the voltage gain  (C) to safeguard the transistor against overheating  (D) to match the load impedance with dynamic output resistance of the transistor

asked May 12, 2018 in Amplifier by Shimroz123
1 answer 10 views

For an earth station transmitter, with an antenna output power of 40dBW 10,000W, a back-off loss of 3dB, a total branching and feeder loss of 3dB, a total branching and feeder loss of 3dB and transmit antenna gain of 4dB, the effective isotropic radiated power (EIRP will be  a) 38dBW b) 40 dBW c 36 dBW d) 47 dBW

asked Jun 15, 2018 in Electronics Engineering by Shimroz123
0 answers 49 views

A high-pass filter has a resistance R = 2 kΩ The lowest input frequency to be passed is 7.5 kHz. The value of suitable coupling capacitor must be: A) 0.001 pico Farad B) 0.01 pico Farad C) 0.1 pico Farad D) 1 pico Farad

asked Jun 4, 2018 in Electrical Engineering by Shimroz123
0 answers 27 views

A high pass filter has a resistance R = 2 kΩ. The lowest input frequency to be passed is 7.5 KHz. The value of suitable coupling capacitor must be : (A) 0.1 pF (B) 1 pF (C) 0.1 μ F (D) 1 μ F

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

In order to reduce the harmful effects of harmonics on the AC side of a high voltage DC transmission system_____ are provided. (A) synchronous condensers (B) shunt capacitors (C) shunt filters (D) static compensators

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 15 views

An inductor of Q factor 10 is connected in series with a capacitor having a Q factor of 100. The overall Q factor of the circuit is :  (A) 100/11 (B) 11/100 (C) 110 (D) 1000

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

A DC reactor is connected in series with each pole of a converter station in order to: A) prevent commutation failures in the inverter B) supply reactive power to the converter C) improve system stability D) increase the power transfer capability

asked Jun 4, 2018 in Power system by Shimroz123
1 answer 20 views

In which type of AC to DC converter efficiency is higher :

asked May 15, 2018 in Power electronics converters by Shimroz123
0 answers 26 views

A 200 V dc motor takes a field current of 2 A to generate a back emf of 180 V. If the field winding resistance is 80 Ω, the resistance of the shunt field regulator is (A) 10 Ω (B) 20 Ω (C) 100 Ω (D) 180 Ω

asked Jun 4, 2018 in Electrical Machine by Shimroz123
1 answer 12 views

A single phase transformer is designed to operate from 50 Hz, 1100 V supply and to have an output voltage of 240 V at no load. The core has mean area of 30 cm2 and the flux density has not to exceed 1.3T. The number of secondary turns will be (a) 1270 (b) 1017 (c) 768 (d) 277  

asked May 25, 2018 in Single phase transformer by Shimroz123
1 answer 18 views

Bundled conductors are mainly used in high voltage overhead transmission lines to (a) Reduce line loss (c) Reduce corona (b) Reduce harmonics (d) Increase strength

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the input code 1010:  (1) 0.3125 V (2) 3.125 V (3) 0.78125 V (4) –3.125 V

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

A chopper operating at a fixed frequency is feeding an R-L load. As they duty ratio of the chopper is increased from 25% to 75%, the ripple in the load current.

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

What is the reactance of a 3H inductor when the frequency is 120 Hz? A. 2260 ohm B. 2060 ohm C. 360 ohm D. 0  

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
2 answers 47 views

The core of a transformer (medium size) uses to provide high flux densities (a) diamagnetic (c) ferromagnetic core (b) paramagnetic (d) none of these

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

The output of an AND gate with three inputs, A, B and C, is HIGH when __________. a) A=1,B=1,C=0 b) A= 0,B= 0,C= 0 ' c) A=1,B=1,C=1 d) A=1,B= 0,C= 1

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 16 views

An inductor is connected in series with SCR to protect it from A) Excessive high voltage B) Excessive high dv/dt C) Excessive high di/dt D) Excessive large forward current 

asked Jun 18, 2018 in Inductor by Shimroz123
0 answers 10 views

Back-to back connection is used in HVDC system to  A) Provide synchronous tie between two systems B) Provide bulk power transmission over long distance C) Provide asynchronous tie between two systems D) Reduce the line voltage drop and the transmission loss

asked Apr 9, 2018 in High voltage engineering by Shimroz123
1 answer 15 views

The transformer works on the principle of: (A) Mutual induction (B) Mutual capacitance (C) All of the above (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

A separately excited dc motor operating in first quadrant is fed from 3-phase semi -converter free -wheeling diode is open circuited, then the motor :  (A) can be operated in first quadrant (B) can be operated in first & second quadrants (C) can be operated in first & fourth quadrants (D) cannot be operated

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
0 answers 24 views

What is the back EMF of a dc motor?

asked Mar 15, 2018 in Electrical Engineering by Quiz
1 answer 27 views

Information that a computer produces and delivers back to the user is known as ____.  a) Input b) Output c) Both (a) and (b) d) None of the above

asked May 13, 2018 in Computer Engineering by Shimroz123
0 answers 16 views

In a 6-pole wave wound dc machine the number of conductors is 70. The back pitch and commutator segments, respectively, are (A) 11and 35 (B) 12 and 34 (C) 13 and 35 (D) 14 and 34 

asked Jun 4, 2018 in Electrical Machine by Shimroz123
1 answer 55 views

Which of the following thyristors can be used for high frequency of operation? A) TRIAC B) DIAC C) SCR D) GTO 

asked Jun 18, 2018 in Thyristor by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...