18 views
in Electrical Engineering by
If the transmission line is loaded with leading reactive volt amperes, there will be rise of voltage at the receiving end and this (a) increases (b) decreases (c) remains same with the increase in the length of line (d) none of these

Related questions

1 answer 46 views

A 100 km long transmission line is loaded at 110 kV.if the loss of line is 5 MW and the load is 150 MVA, the resistance of the line is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 43 views

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

For a short line if the receiving end voltage is equal to the sending end voltage under loaded conditions: a) the sending end power factor is unity b) the receiving -end power factor is unity c) the sending-end power factor is leading d) the receiving end power factor is leading

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

What type of insulator will be used if the direction of the transmission line is to be changed?

asked May 22, 2018 in Electric Power Transmission by Shimroz123
1 answer 49 views

If voltage at the two ends of a transmission line is 132 kV and its reactance is 40 Ohms, the capacity of the line will be: (A) 435.6 MW (B) 217.8 MW(C) 251.5 MW (D) 500 MW

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 21 views

An 800 kV transmission line has a maximum power transfer capacity of P. If it is operated at 400 kV with the series reactance unchanged, the new maximum power transfer capacity is approximately (A) P (B) 2P (C) P / 2 (D) P / 4

asked May 25, 2018 in Power system by Shimroz123
1 answer 50 views

If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.  (A) 11 kV (B) 33 kV (C) 66 kV (D) 132 kV

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 122 views

A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient? A) 0.69 B) 1.69 C) 6.9 D) 16.9 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 47 views

For a given base voltage and base volt-amperes, the per unit impedance value is x. For the doubled base values of both voltage and volt-amperes, the per unit impedance will be (a) 2x (b) 0.25x (c) 0.5x (d) no change 

asked May 25, 2018 in Battery by Shimroz123
1 answer 13 views

A transmission line is operating with a Phase shift of 80° between two ends. If the load is suddenly increased A) The phase displacement will increase B) The phase displacement will decrease C) The phase displacement will not change D) The surge impedance will increase

asked May 24, 2018 in Electrical Engineering by Shimroz123
0 answers 10 views

In CRO, Lissajous pattern will be a straight line, if the two signals are of same frequency with a phase difference of (a) 0° (b) 180° (c) 360° (d) All of these 

asked May 25, 2018 in Oscilloscope by Shimroz123
1 answer 13 views

For a transmission line with negligible losses, the lagging reactive power (VAR) delivered at The receiving end, for a given receiving end voltage, is directly proportional to the?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 13 views

The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to :

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

asked May 29, 2018 in Electrical Engineering by Shimroz123
1 answer 115 views

In a transmission line if booster transformers are to be used, preferred location will be  (A) At the receiving end (B) At the sending end (C) At the intermediate point (D) Anywhere in the line 

asked May 8, 2018 in Electric Power Transmission by Shimroz123
0 answers 20 views

If the supply frequency of a 3-phase induction motor is ‘f’, then frequency of rotor emf at motor slip ‘s’ will be   (a) sf (b) (1 – s)f (c) f/s (d) None of these 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 66 views

In a Y -connected circuit, between each line -voltage and the nearest phase - voltage, there is a phase -angle of: A. 0° B. 30° C. 60° D. 120°

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 33 views

In an AC transmission line difference in phase of voltage at two ends of the line is due to (a) System voltage (b) Insulators (c) Resistance of line (d) Reactance of line

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 27 views

A 12 -pole, 440 V, 50 Hz, 3 -phase synchronous motor takes a line current of 100 A at 0.8 pf leading. Neglecting losses, the torque developed will be

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

Consider the following statements : If a high Q parallel resonant circuit is loaded with a resistance  1. The circuit impedance reduces.  2. The resonant frequency remains the same.  3. The bandwidth reduces.  Which of the above statements is/are correct ?

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

A motor which can conveniently be operated at lagging as well as leading power factors is the:   (A) squirrel cage induction motor (C) synchronous motor (B) wound rotor induction motor (D) DC shunt motor

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

In a d.c. series motor, the torque developed is 20 Nm at 10A. If the load current is doubled, the new torque will be : -  a) 60 Nm b) 45 Nm c) 80 Nm d) 100 Nm

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 15 views

A series RLC circuit resonate at 200 Hz. If the capacitance is increased to four times, the circuit will be in resonance at   (a) 100 Hz (b) 200 Hz (c) 400 Hz (d) 800 Hz  

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 185 views

For a 66 kV line having span of 200 meters between towers the approximate sag will be 2 m. If the span is double the sag will be:  (A) 1 m (B) 2 m (C) 4m (D) 8m

asked May 8, 2018 in Electric Power Distribution by Shimroz123
1 answer 16 views

If Voltage Standing Wave Ratio, (VSWR) of a wave is 2, its reflection coefficient will be _____.

asked May 29, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

if voltage is 230 Volts , frequency is 50 Hz and current is 1 ampere then what will be the resistance?

asked Dec 4, 2017 in Electrical Engineering by Quiz
2 answers 52 views

If resistance is 8 Ohm and current is 16 ampere then what will be the voltage and power?

asked Oct 21, 2017 in Electrical Engineering by Quiz
0 answers 44 views

If a four pole synchronous generator driven at 1500 rpm feeds a 6-pole induction motor, which is loaded to run at a slip of 5%, then speed of the motor will be   (a) 1000 rpm (b) 950 rpm (c) 1500 rpm (d) 1450 rpm

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be :  (A) 34.64 kVA (B) 75 kVA (C) 20 kVA (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 380 views

The main consideration for operating transmission line at high voltage is (a) to increase efficiency only. (b) to reduce power loss only. (c) to increase power transmission capability only. (d) All of the above

asked May 26, 2018 in Electric Power Transmission by Shimroz123
2 answers 26 views

Three lamps are connected in parallel across a 120 Volt source. If one lamp burns out, the remaining two will be: A. Glow dimmer B. Glow brighter C. Not light D. Glow with the same brightness as before

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 42 views

If 5000 kW power is transmitted at 220 kV in place of 11 kV, reduction in the value of electric current will be (a) 90% (b) 95% (c) 5% (d) 10% 

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 15 views

When the north poles of two bar magnets are brought close together, there will be: A. no force B. a downward force C. a force of attraction D. a force of repulsion

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

If a transformer is continuously operated the maximum temperature rise will occur in?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 19 views

A transmission line of 200 km has a certain A, B, C and D parameters. If the length is reduced to 60 km

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 62 views

The corona loss of a 3-phase transmission line is 100 kW at 60 kV/phase and 25 kW at 50 kV/phase. The disruptive critical voltage is (A) 40 kV (B) 43.6 kV (C) 49.6 kV (D) 50 kV

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 54 views

If a transformer primary is energised from a square wave voltage source, its output voltage will be a:  (A) square wave (B) sine wave (C) triangular wave (D) pulse wave

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 24 views

Precise control of reactive current flow entering the transmission and distribution systems can be minimized by using (A) synchronous condenser (B) static VAR capacitor (C) capacitor bank (D) thyristor switched reactor in parallel with capacitor

asked Apr 28, 2018 in Power system by Shimroz123
1 answer 15 views

A three-phase cage induction motor is started by direct-on-line (DOL) switching at the rated voltage. If the starting current drawn is 6 times the full load current, and the full load slip is 4%, then ratio of the starting developed torque to the full load torque is approximately equal to (A) 0.24 (B) 1.44 (C) 2.40 (D) 6.00

asked May 17, 2018 in Induction Machine by Shimroz123
1 answer 22 views

Suggest the energy conservation techniques in following cases : (i) Motor is running with 70% loaded condition. (ii) Motor is continuously loaded at 50%. (iii) Motor runs with 30% loaded condition but sometimes rises to 50% loading condition. (iv) Motor runs continuously under no-load condition.

asked Oct 3, 2018 in Energy Conservation And Audit by Shimroz123
0 answers 28 views

 A DC shunt motor having unsaturated magnetic circuit runs at 1000 rpm with rated voltage If the applied voltage is reduced to half of the rated voltage, the motor will run at (A) 2000 rpm (B) 1000 rpm (C) 750 rpm (D) 500 rpm

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 40 views

 If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be A) Large in amplitude B) Small in amplitude C) Distorted D) Distortion less

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 23 views

If a capacitance is charged by a square wave current source, then the voltage across the capacitor will be (a) Square wave (b) Step function (c) Triangular wave (d) Zero

asked May 25, 2018 in Capacitance by Shimroz123
0 answers 24 views

The sending and receiving end voltages of a three phase transmission line at 100 MW load are equal at 230 KV. The phase line impedance is j14 ohm. Calculate the maximum steady state power that can be transmitted over the line.  (A) 3778.5 MW (B) 2234.56 MW (C) 1784.19 MW (D) 512.37 MW

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

The output of a 2-input NAND gate with high at both the inputs will be • High • Low • High & low • None of the above.

asked May 14, 2018 in Digital Electronics by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...