34 views
in Electrical Engineering by
An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave amplitude is (a) 8V (b) 4.82 V (c) 2.02 V (d) 1.592 V

1 Answer

0 votes
by
Slew rate = 2πfv

where v is the amplitude

V=(1/2π*0.1) = 1.592V

Related questions

0 answers 70 views

An op-amp having a slew rate of 62.8 V/msec, is connected in a voltage follower configuration. If the maximum amplitude of the sinusoidal input is 10 V, then the minimum frequency at which the slew rate limited distortion would set in at the output is  (A) 1 MHz (B) 6.28 MHz (C) 10 MHz (D) 62.8 MHz

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

An OP amp has an open loop gain of 1,00,000. If the feedback fraction is 0.02, the approximate closed loop gain is (a) 1 (b) 1,00,000 (c) 50 (d) 0.02

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: (1) Has no offset (2) Approaches to triangular waveshape (3) Is pure sinusoidal (4) Is square wave 

asked May 29, 2018 in Amplifier by Shimroz123
1 answer 13 views

A sine wave of 15 kHz is changing at a faster rate than a sine wave with a frequency of? B.12 kHz C.18 kHz D.1.3 MHz

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 11 views

A 100 pF capacitor has a maximum charging current of 150 μA.What is the slew rate ? (A) 1.5 V/μs (B) 1.05 V/μs (C) 0.15mV/s (D) 10.5 mV/s

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 31 views

A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 29 views

The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - a) 225 MHz b) 1.06 MHz c) 10 KHz d) 10 MHz

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
0 answers 16 views

For a resonant circuit with resonant frequency of 1 MHz a, 0 = 50 and R = 400, find the value of C (A) 250 pF (B) 1000 pF (C) 1.25 pF (D) 500 pF

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

Output of an op-amp is a square wave of 4 V peak to peak with a rise time of 5 microsecond and fall time of 4 microsecond.Maximum frequency (in kHz)of undistorted sine wave output of 2 V peak to peak is about  A) 100 B) 150 C) 200 D) 250

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 31 views

In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the (A) applied load (B) internal compensation (C) impedance of the source (D) power dissipation in the chip

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
0 answers 29 views

A system function has a pole at s=0 and a zero at s= -1. The constant multiplier is unity. For an excitation cos(t), What is the steady-state response?  (A) √2sin(t+450) (B) √2sin(t-450) (C) sin(t-450) (D) Sin(t) 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 11 views

A peak reading voltmeter has been calibrated with a sine wave signal and scaled in rms volts. If a square wave signal ± 1V peak is applied, the meter reading will be (a) 0.555 V (b) 0.707 V (c) 1 V (d) 1.75 V

asked May 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 8 views

One sine wave has a positive - going zero crossing at 15° and another sine wave has a positive - going zero crossing at 55°. The angle between the two waveforms is -  a) 0° b) 45° c) 40° d) None of the above

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

When a sine wave has a frequency of 100 Hz in 12 s it goes through? A.1/100 cycle B.12 cycles C.120 cycles D.1,200 cycles

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 11 views

An Op-amp as a voltage follower has a voltage gain of

asked May 14, 2018 in Amplifier by Shimroz123
0 answers 10 views

A SCR has an anode supply of sine voltage 200V rms, 50 Hz applied through a 100Q resistor and fired at an angle of 60°. Assuming no voltage drop, the rms value of the output voltage is : (A) 89,7 V (B) 126.7 V (C) 166.7 V (D) 288.28 V

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current? A. 30 A/s B. 20 A/s C. 10 A/s D. none of these

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 9 views

An ideal Op Amp has  (a) infinite input and output impedance (b) very low input and output impedance (c) low input impedance and very high output impedance (d) infinite input impedance and zero output impedance

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 22 views

An overhead transmission line has a span of 260 m. The weight of the conductor is 0.68 kg/m. The maximum allowable tension in the line is 1550 kg. Maximum sag of the line should be (a) 5.8 m (b) 4.6 m (c) 2.7 m (d) 3.7 m 

asked May 25, 2018 in Electric Power Transmission by Shimroz123
0 answers 52 views

A dominant pole compensated op-amp has openloop gain of 100 dB and -3 dB bandwidth of 50 Hz. If it is connected as inverting amplifier for a gain of 20 dB the -3 dB bandwidth is about  A) 500 kHz B) 50 kHz C) 5 kHz D) 500 Hz

asked Apr 5, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 21 views

An 800 kV transmission line has a maximum power transfer capacity of P. If it is operated at 400 kV with the series reactance unchanged, the new maximum power transfer capacity is approximately (A) P (B) 2P (C) P / 2 (D) P / 4

asked May 25, 2018 in Power system by Shimroz123
1 answer 15 views

The input voltage to an OP AMP is a large voltage step. The output is an exponential waveform that changes to 0.25 V in 0.1µs (microsecond). The slew rate of the OP AMP is : -  a) 5V/µs b) 2.5 V/ µs c) 3V/µs d) 4.5V/ µs

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 48 views

A step voltage E is applied to a series R-L circuit. The rate of change of current is maximum at t = _:  (1) Zero (2) Infinity (3) L/R (4) R/L 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 12 views

In a PCM system the number of quantization level are 16 and the maximum signal frequency is 4 KHz the transmission bit rate is

asked May 23, 2018 in Electronics communication by Shimroz123
1 answer 18 views

The rate of rise of current through an inductive coil is maximum?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

The input impedance of an op-amp is • High • Low • Medium • None of the above

asked May 14, 2018 in Amplifier by Shimroz123
1 answer 19 views

The closed loop gain of an OPAMP is dependent upon, whether the OP AMP is used : -  a) in inverting mode b) in non -inverting mode c) is independent of the fact whether the input is connected to inverting or non -inverting terminal d) is depending upon the fact whether the input is connected to inverting or non -inverting terminal

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
0 answers 15 views

What is the gain of an op amp?

asked Mar 10, 2018 in Analog electronics circuits by Quiz
1 answer 40 views

 If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be A) Large in amplitude B) Small in amplitude C) Distorted D) Distortion less

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 17 views

DC ammeter has a resistance of 0.1 Ω and its current range is 0-100 A. If the range is to be extended to 0-300 A, what shunt resistance need to be connected?  A) 0.025 Ω B) 0.05 Ω C) 0.015 Ω D) 0.03 Ω

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

An accelerometer has input range of 0 to 10g, natural frequency 30 Hz and mass 0.001 kg. The range of the secondary displacement transducer in mm required to cover the input range is (A) 0 to 2.76 (B) 0 to 9.81 (C) 0 to 11.20 (D) 0 to 52.10

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
0 answers 21 views

To generate 1 MHz signal, the most suitable circuit is (a) Wein bridge oscillator (b) Phase shift oscillator (c) Colpitts oscillator (d) None of these  

asked May 25, 2018 in Electronics Engineering by Shimroz123
1 answer 60 views

A pulse compression radar transmits an encoded pulse having a frequency chirp from 990 MHz to 1010 MHz centred around 1 GHz. The range resolution capability of this radar is A) 7.5 m B) 7.5 Km C) 75 m D) 750 m 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 28 views

 A transformer has maximum efficiency at 3/4 full load. The ratio of its iron losses and full load copper loss is : -  a) 16/9 b) 4 / 3 c) 3/4 d) 9 /16

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

 In an electronic ohmmeter an op -amp is used as a: -  a) sommer b) multiplier c) buffer amplifier d) integrator

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
0 answers 22 views

On chip oscillator of 8051 has a nominal frequency (in MHz) of  A) 2 B) 8 C) 10 D) 12

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 10 views

What is the average value of a perfect sine wave over a complete cycle ? (A) Zero (B) Peak value (C) rms value (D) None of the above

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
2 answers 238 views

The equation of 50 Hz current sine wave having r.m.s. value of 60 A is?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 3 views

State any two characteristics of an ideal Op-amp.

asked Sep 13, 2018 by Shimroz123
1 answer 18 views

The maximum reluctance power of a salient-pole synchronous motor having direct-axis reactance, 1.0 pu and quadrature-axis reactance, 0.5 pu, and input voltage, 1.0 pu is (A) 0.25 pu (B) 0.5 pu (C) 1.0 pu (D) 1.5 pu

asked Apr 28, 2018 in Electrical Machine by Shimroz123
0 answers 33 views

What is the Output voltage of Op-amp for input voltage of Vi1=150 μV,Vi2=140 μV if the amplifier has differential gain of Ad=4000 and value of CMRR is 100. 

asked Apr 4, 2018 in Electrical Engineering by Shimroz123
1 answer 47 views

 A pulse radar has a pulse repetition frequency (PRF) of 3 KHz. If the radar is emitting at 10 GHz, what is the maximum unambiguous range for this radar? A) 5 Km B) 5 m C) 50 Km D) 15 m 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
0 answers 50 views

A moving coli ammeter has a fixed shunt of 0.02 Ω with a coil circuit resistance of R=1 kΩ and needs potential of 0.5 V across it for full scale deflection. Calculate the value of shunt to give full scale deflection when the total current is 10 A. (1) 0.05 Ω (2) 0.005 Ω (3) 0.5 Ω (4) 0.0005 Ω

asked Apr 11, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...