Can you help by answering this question?

An FET is a ....

29 views
in Electrical Engineering by
An OP amp has an open loop gain of 1,00,000. If the feedback fraction is 0.02, the approximate closed loop gain is (a) 1 (b) 1,00,000 (c) 50 (d) 0.02

1 Answer

0 votes
by
The closed loop gain Ag = G/(1+G*f)

Where G is the open loop gain and f is the feedback fraction 

So Ag = 49.975

Related questions

1 answer 19 views

The closed loop gain of an OPAMP is dependent upon, whether the OP AMP is used : -  a) in inverting mode b) in non -inverting mode c) is independent of the fact whether the input is connected to inverting or non -inverting terminal d) is depending upon the fact whether the input is connected to inverting or non -inverting terminal

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 11 views

An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

asked May 20, 2018 in Amplifier by Shimroz123
1 answer 34 views

An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave amplitude is (a) 8V (b) 4.82 V (c) 2.02 V (d) 1.592 V

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 34 views

If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is (a) – 13.3 (b) 200 (c) 8 (d) 10 

asked May 25, 2018 in Amplifier by Shimroz123
1 answer 21 views

For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 11 views

An Op-amp as a voltage follower has a voltage gain of

asked May 14, 2018 in Amplifier by Shimroz123
0 answers 14 views

An electromechanical closed –loop control system has the transfer function C(s)/R(s) = k/s (s2 + s +1) (s+ 4) +k. Which one of the following is correct?  (A) The system is stable for all positive values of k (B) The system is unstable for all values of k (C) The system is stable for values of k between zero and 3.36 (D) The system is stable for values of k between 1.6 and 2.45 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 28 views

An amplifier without feedback has a gain of 1000. The gain with a negative feedback of 0.009 is  A) 10 B) 100 C) 125 D) 900

asked May 20, 2018 in Amplifier by Shimroz123
1 answer 19 views

In closed loop control system, with positive value of feedback gain the overall gain of the system will

asked Mar 27, 2018 in Control System by Shimroz123
1 answer 37 views

If the characteristics equation of a closed loop system is s2+2s+2=0, then the system is  (A) Over damped (B) Critically damped (C) Under damped (D) Undamped 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 22 views

An open-loop system is better than a closed-loop system in terms of   (a) Accuracy (b) Stability (c) Noise reduction (d) Sensitivity  

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

The characteristic equation for a closed loop system with forward gain K is s4 + 4s3 + 8s2 + 6s + K = 0. The critical gain value Kc for stability should not exceed  (a) 3.25 (b) 9.75 (c) 13.0 (d) 23.3

asked May 15, 2018 in Control System by Shimroz123
0 answers 15 views

What is the gain of an op amp?

asked Mar 10, 2018 in Analog electronics circuits by Quiz
0 answers 54 views

A moving coli ammeter has a fixed shunt of 0.02 Ω with a coil circuit resistance of R=1 kΩ and needs potential of 0.5 V across it for full scale deflection. Calculate the value of shunt to give full scale deflection when the total current is 10 A. (1) 0.05 Ω (2) 0.005 Ω (3) 0.5 Ω (4) 0.0005 Ω

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 36 views

What will happen to the gain margin if the gain of the open loop system is doubled? A) Doubled B) Becomes half C) Is not affected D) Becomes one-fourth 

asked Jun 18, 2018 in Control System by Shimroz123
1 answer 44 views

If the gain of the open loop system is doubled, the gain margin  (1) Is not affected (2) Gets doubled (3) Becomes half (4) Becomes one -forth

asked Apr 30, 2018 in Control System by Shimroz123
0 answers 52 views

A dominant pole compensated op-amp has openloop gain of 100 dB and -3 dB bandwidth of 50 Hz. If it is connected as inverting amplifier for a gain of 20 dB the -3 dB bandwidth is about  A) 500 kHz B) 50 kHz C) 5 kHz D) 500 Hz

asked Apr 5, 2018 in Electronics Engineering by Shimroz123
0 answers 16 views

As compared to a closed loop system an open loop system is  (a) more stable as well as more accurate (b) less stable as well as less accurate (c) more stable but less accurate (d) less stable but more accurate

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 33 views

What is the Output voltage of Op-amp for input voltage of Vi1=150 μV,Vi2=140 μV if the amplifier has differential gain of Ad=4000 and value of CMRR is 100. 

asked Apr 4, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

lf slip of an induction machine is 0.02 and the stator supply frequency is 50 Hz, what will be the frequency of the rotor induced e.m.f.? (A) 10 Hz (B) 50 Hz (C) 1 Hz (D) 2500 Hz

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 34 views

An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is  (1) 141 (2) 92.3 (3) 9.23 (4) 1.41

asked May 1, 2018 in Power Electronics by Shimroz123
0 answers 17 views

DC ammeter has a resistance of 0.1 Ω and its current range is 0-100 A. If the range is to be extended to 0-300 A, what shunt resistance need to be connected?  A) 0.025 Ω B) 0.05 Ω C) 0.015 Ω D) 0.03 Ω

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

Order of the open loop transfer function is _____ to order of closed loop transfer function   (a) not equal (b) equal (c) less than (d) greater than 

asked May 13, 2018 in Control System by Shimroz123
1 answer 95 views

A differential amplifier has a differential gain of 20,000, CMRR : 80 dB. The common mode gain is given by

asked May 3, 2018 in Power Electronics by Shimroz123
0 answers 17 views

A diesel power station spends 0.25 kg/kWh fuel. If the calorific value is 10,000 kcal/kg then overall efficiency of the power station will be   (a) 25% (b) 30% (c) 34.4% (d) 100% 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 70 views

An op-amp having a slew rate of 62.8 V/msec, is connected in a voltage follower configuration. If the maximum amplitude of the sinusoidal input is 10 V, then the minimum frequency at which the slew rate limited distortion would set in at the output is  (A) 1 MHz (B) 6.28 MHz (C) 10 MHz (D) 62.8 MHz

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 15 views

The sensitivity of a closed loop system to gain changes and load disturbances depends upon (a) forward gain (b) loop gain (c) frequency (d) all the above 

asked May 25, 2018 in Control System by Shimroz123
1 answer 20 views

After drawing the Root-Locus, the closed-loop poles corresponding to a specified value of gain K can be determined from which of the following criterion ? (A) Magnitude criterion alone (B) Angle criterion alone (C) Both Magnitude and Angle criteria (D) Angle of departure and angle of arrival.

asked Apr 28, 2018 in Control System by Shimroz123
0 answers 9 views

An ideal Op Amp has  (a) infinite input and output impedance (b) very low input and output impedance (c) low input impedance and very high output impedance (d) infinite input impedance and zero output impedance

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 32 views

Which of the following is an example of an open loop system ? (A) Household refrigerator (B) Respiratory system of an animal (C) Stabilisation of air pressure entering into a mask (D) Execution of a program by a computer

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
0 answers 30 views

A system function has a pole at s=0 and a zero at s= -1. The constant multiplier is unity. For an excitation cos(t), What is the steady-state response?  (A) √2sin(t+450) (B) √2sin(t-450) (C) sin(t-450) (D) Sin(t) 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

A system has 14 poles and 2 zeros in its open -loop transfer function. The slope of its highest frequency asymptote in its magnitude plot is (a) - 40 dB/dec (b) - 240 dB/dec (c) + 40 dB/dec (d) + 240 dB/dec

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 11 views

Addition of a pole to the open loop transfer function has the effect of (A) Pulling the root locus to the left (B) Pulling the root locus to the right (C) Either (A) or (B) (D) Does not have any effect on the root locus

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

asked May 29, 2018 in Amplifier by Shimroz123
1 answer 8 views

The input impedance of an op-amp is • High • Low • Medium • None of the above

asked May 14, 2018 in Amplifier by Shimroz123
1 answer 11 views

In the ideal closed loop operational amplifier, the gain depends on (A) value of the series component (B) value of the feedback component (C) on the operational amplifier itself (D) both A and B

asked May 12, 2018 in Electronics communication by Shimroz123
1 answer 15 views

Negative feedback in a closed-loop control system DOES NOT (A) reduce the overall gain (B) reduce bandwidth (C) improve disturbance rejection (D) reduce sensitivity to parameter variation

asked Apr 26, 2018 in Control System by Shimroz123
0 answers 15 views

With the introduction of negative feedback, the gain—bandwidth product of an amplifier  A) Becomes infinity B) Increases C) Decreases D) Remains constant

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is

asked Apr 1, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

Output of an op-amp is a square wave of 4 V peak to peak with a rise time of 5 microsecond and fall time of 4 microsecond.Maximum frequency (in kHz)of undistorted sine wave output of 2 V peak to peak is about  A) 100 B) 150 C) 200 D) 250

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

The input voltage to an OP AMP is a large voltage step. The output is an exponential waveform that changes to 0.25 V in 0.1µs (microsecond). The slew rate of the OP AMP is : -  a) 5V/µs b) 2.5 V/ µs c) 3V/µs d) 4.5V/ µs

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
0 answers 126 views

An electron having an energy of 20 eV enters a magnetic field of 0.02 webers/sqm at an angle of 30degrees to the field. The time of travel (in nS)of the electron for one revolution is about  A) 1.78 B) 4.21 C) 7.82 D) 10.24 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

In root locus plot, a point on the real axis lies on the locus, if the number of open loop poles plus zeros on real axis to the a) left of the point is odd b) left of the point is even . c) right of the pointis odd d) right of the point is even

asked May 23, 2018 in Control System by Shimroz123
1 answer 3 views

State any two characteristics of an ideal Op-amp.

asked Sep 13, 2018 by Shimroz123
1 answer 22 views

 In an electronic ohmmeter an op -amp is used as a: -  a) sommer b) multiplier c) buffer amplifier d) integrator

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 81 views

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,085 users

...