Can you help by answering this question?

The resistivity of a semiconductor material increases as :

8 views
in Instrumentation and control by
Converter is a device for transforming (A) ac to dc (B) dc to dc (C) dc to ac (D) ac to ac

1 Answer

0 votes
by

Converter is a device for transforming ac to ac

Related questions

1 answer 8 views

Which of these is not a photoelectric device ?  a) Photoconductive cells Photoemissive cells c) Photoresistive cells d) Photovoltaic cells

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 22 views

A digital voltmeter uses an A/D converter which needs a start pulse, uses an analog comparator and has a relatively fixed conversion time independent of the applied voltage. The A/D converter is : -  a) Successive Approximation Converter .b) Digital Ramp Converter c) Digital Slope Converter d) All the above

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 5 views

Which semiconductor device acts like a diode and two transistor : -  a) SCR b) Triac c) UJT d) Diac

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 30 views

A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the input code 1010:  (1) 0.3125 V (2) 3.125 V (3) 0.78125 V (4) –3.125 V

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 38 views

 Which of the following is a negative-resistance microwave device for oscillator applications? A) IMPATT Diode B) Gunn Diode C) Snap diode D) Schottky Diode 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 55 views

SiN is used in semiconductor industry such as a diffusion mask during device processing, a dielectric for memory devices because it offers a (a) High breakdown field strength and a low fixed interface charge density. (b) Low breakdown field strength and a high fixed interface charge density. (c) High breakdown field strength and a high fixed interface charge density. (d) Low breakdown field strength and a low fixed interface charge density.

asked Apr 14, 2018 in Electrical Engineering by Zeeshan
0 answers 17 views

For measuring the frequency of an unknown A.C. source. Which of the following device is necessary to obtain a standard waveform?  (A) Operational amplifier (B) Astable multivibrator (C) Schmitt trigger (D) Monostable multivibrator

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 71 views

 The term absolute Pressure is used for a pressure measured relative to: - a) vacuum pressure b) some fixed pressure c) atmospheric d) all the above

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 9 views

The Kirchoff's law for a.c. is applicable upon consideration of -  a) Phasor sum b) Algebraic sum c) Progression sum d) Linear sum

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
0 answers 21 views

Describe the gate circuit for a single phase full converter.

asked Mar 11, 2018 in Power Electronics by Quiz
1 answer 50 views

Which of the following device is used for coupling microwave energy?  A) Resonator B) Waveguide C) Loop D) Antenna

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 18 views

The most common device used for detection in radio receivers is   (A)amplifier (B) triode (C) diode (D) transistor

asked May 17, 2018 in Electronics communication by Shimroz123
1 answer 10 views

The device used for voltage regulator is

asked May 14, 2018 in Electronics Engineering by Shimroz123
0 answers 12 views

The device complexity is highest for memory  A) Flash B) EEPROM C) PROM D) EPROM

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 23 views

Thermocouple instruments can be used for a frequency range upto   (a) 100Hz (b) 5000 Hz (c) 1 MHz (d) 50 MHz and above 

asked May 13, 2018 in Instrumentation and control by Shimroz123
1 answer 10 views

 A Wheatstone bridge cannot be used for precision measurements because errors are introduced into on account of: - a) Resistance of the connecting lead b) Thermoelectric EMFs c) Contact resistance d) all the above

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 40 views

Which amongst the following has a negative coefficient of temperature for resistance?  a) Copper b) Lead c) Carbon d) Aluminium

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 11 views

Superposition theorem stays valid for a : -  a) LTI system b) Discrete system c) LT systems d) None of these

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 17 views

Which one of the following frequency meter is suitable for measuring radio frequency?   (a) Vibrating reed frequency meter (b) Weston frequency meter (c) Electrical resonance frequency meter (d) Heterodyne frequency meter 

asked May 13, 2018 in Instrumentation and control by Shimroz123
1 answer 9 views

Knowledge of Transfer Function is necessary for the calculation of: - a) The Time Constant b) The output for a given input c) The steady state gain d) The order of the system

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 9 views

Transfer function is defined for: - a) Linear and time invariant System b) Linear and time variant system c) Non -Linear time invariant system d) Non -Linear and time variant system

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 9 views

 Maxwell's inductance - capacitance bridge is used for measurement of Inductance of: -  a) Low Q coils b) Medium Q coils c) High Q coils d) Low and medium Q coils

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
0 answers 90 views

 When The dc converter in figure shown has a resistance load of R = 10 Ω and the input voltage is Vs 220 V the converter switch remains on, its voltage drop is Vo -2 V. The chopping frequency is fI K sW Vs If the duty cycle is 50%, determine: (a) the average output voltage V (b) the RMS output voltage Vo (c) the converter efficiency (d) the effective input resistance of the converter

asked Apr 26 by Hussein
1 answer 25 views

A DC reactor is connected in series with each pole of a converter station in order to: A) prevent commutation failures in the inverter B) supply reactive power to the converter C) improve system stability D) increase the power transfer capability

asked Jun 4, 2018 in Power system by Shimroz123
1 answer 390 views

The number of comparators required in a 3-bit comparator type analog to digital converter is  A) 2 B) 3 C) 7 D) 8 

asked May 20, 2018 in Digital Electronics by Shimroz123
1 answer 7 views

The ripple content of load current of a converter feeding RL load is decided by  A) Load resistance alone B) Load inductance alone C) Both load resistance and load inductance D) Neither resistance nor inductance

asked May 20, 2018 in Power electronics converters by Shimroz123
1 answer 7 views

In a thyistorised converter a free wheeling diode is used to  A) Add to the conduction current ofthe thyristor B) Oppose the thyristor conduction C) Conduct current during the off period of the thyristor D) Protect the thyristor by providing a shunt path

asked May 20, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 18 views

A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high load inductance. The input displacement factor (IDF) and the input power factor (IPF) of the converter will be  (A) IDF IPF = = 0.867; 0.828 (B) IDF IPF = = 0.867; 0.552 (C) IDF IPF = = 0.5; 0.478 (D) IDF IPF = = 0.5; 0.318 

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 20 views

A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is  (A) 119.05 A (B) 79.37 A (C) 68.73 A (D) 39.68 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 15 views

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is  (A) 0.78 (B) 0.827 (C) 0.866 (D) 0.9

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 16 views

A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component of input current will respectively be  (A) 31% and 6.8 A (B) 31% and 7.8 A (C) 66% and 6.8 A (D) 66% and 7.8 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 16 views

In D/A converter, the resolution required is 50mv and the total maximum input is 10v. The number of bits required is   (A) 7 (B) 8 (C) 9 (D) 200

asked May 17, 2018 in Digital Instrumentation by Shimroz123
1 answer 16 views

A converter which can operate in both 3 pulse and 6 pulse mode is a  (A) 1 phase full converter (B) 3 phase half wave converter (C) 3 phase semi converter (D) 3 phase full converter.

asked May 17, 2018 in Power electronics converters by Shimroz123
1 answer 18 views

In an R-2R ladder D/A converter, the input resistance is  1. Not same for all digital inputs 2. R for each input 3. 2R for each input 4. 3R for each input 

asked May 13, 2018 in Electronics Engineering by Shimroz123
1 answer 6 views

In a single-phase full converter, the number of SCRs conducting during overlap is   (a) 1 (b) 2 (c) 3 (d) 4 

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 50 views

The percent resolution of an 8 -bit D/A converter is

asked May 3, 2018 in Power Electronics by Shimroz123
1 answer 16 views

A separately excited dc motor operating in first quadrant is fed from 3-phase semi -converter free -wheeling diode is open circuited, then the motor :  (A) can be operated in first quadrant (B) can be operated in first & second quadrants (C) can be operated in first & fourth quadrants (D) cannot be operated

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 41 views

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 36 views

A Unified Power Flow Controller (FACTS controller) is a voltage source converter based (A) Inter-phase power controller (B) Static Compensator (C) Combination of series and shunt compensators (D) Solid-state series compensator

asked Apr 28, 2018 in High voltage engineering by Shimroz123
1 answer 33 views

In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in (A) voltage notching (B) harmonic distortion (C) voltage sag (D) voltage swell

asked Apr 28, 2018 in Electronics Engineering by Shimroz123
0 answers 21 views

A single phase fully controlled thyristor bridge ac -dc converter is operating at a firing angle of 25 degree and an overlap angle 10 degree with constant dc output current of 20A. The fundamental power factor (displacement factor) at input ac mains is : (A) 0.78 (B) 0.827 (C) 0.866 (0) 0.9

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 57 views

A cyclo converter is a   (a) naturally commutated device (b) forced commutated device (c) can be commutated in both manner (d) None of the above 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 24 views

A thyristor power converter is said to be in discontinuous when:  (A) The load current is zero even though the load voltage is present. (B) Both load voltage and load current are zero simultaneously. (C) The load current is present even though load voltage is zero. (D) When load current is ripple free. 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...