Can you help by answering this question?

What are semiconductors?

12 views
in Instrumentation and control by
An amplifier has a voltage gain of 50; this gain in dB will be (A) 34 dB (B) 68 dB (C) 41 dB (D) 14 dB 

1 Answer

0 votes
by

An amplifier has a voltage gain of 50; this gain in dB will be 34 dB

Related questions

1 answer 64 views

An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

asked May 3, 2018 in Power Electronics by Shimroz123
1 answer 58 views

A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 25 views

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

asked May 29, 2018 in Amplifier by Shimroz123
0 answers 52 views

A dominant pole compensated op-amp has openloop gain of 100 dB and -3 dB bandwidth of 50 Hz. If it is connected as inverting amplifier for a gain of 20 dB the -3 dB bandwidth is about  A) 500 kHz B) 50 kHz C) 5 kHz D) 500 Hz

asked Apr 5, 2018 in Electronics Engineering by Shimroz123
1 answer 93 views

A differential amplifier has a differential gain of 20,000, CMRR : 80 dB. The common mode gain is given by

asked May 3, 2018 in Power Electronics by Shimroz123
1 answer 34 views

An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is  (1) 141 (2) 92.3 (3) 9.23 (4) 1.41

asked May 1, 2018 in Power Electronics by Shimroz123
0 answers 21 views

The RF amplifier A is having 3 dB NF & 5 dB of gain, amplifier B is having 3.5 dB NF & 15 dB . For overall noise figure of the cascaded system, the correct statement is :  a. A as first stage & B as second stage offers minimum over all NF b. B as first stage & A as second stage minimum over all NF c. Both the combination will offer same overall NF d. Over all NF will be less than 3 dB.

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 13 views

A certain common-emitter amplifier has a voltage gain of 100. If the emitter bypass capacitor is removed.  a. The circuit will become unstable b. The voltage gain will decrease  c. The voltage gain will increase d. The circuit will become stable

asked Aug 31, 2018 by Shimroz123
1 answer 28 views

An amplifier without feedback has a gain of 1000. The gain with a negative feedback of 0.009 is  A) 10 B) 100 C) 125 D) 900

asked May 20, 2018 in Amplifier by Shimroz123
0 answers 38 views

An amplifier which has almost same gain and input resistance of a CE amplifier but of higher bandwidth is  A) Cascode amplifier B) Cascade amplifier C) Darligton amplfier D) CC amplifier

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 27 views

A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 20 views

For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 14 views

With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across the diode? a) 0.3V b) 0.7V c) 0.9V d) 1.4V

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 11 views

An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

asked May 20, 2018 in Amplifier by Shimroz123
1 answer 12 views

A d.c. voltage of 230 V is imposed on an unloaded 230 V, 50 Hz transformer, it will (A) give high secondary voltage (B) burn out (C) give secondary voltage as per k (D) None of these

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

An Op-amp as a voltage follower has a voltage gain of

asked May 14, 2018 in Amplifier by Shimroz123
1 answer 12 views

Which amplifier will be preferred for highest gain?  (1) Darlington pair (2) Cascade amplifier (3) Cascode amplifier (4) Depends on the circuitry

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
2 answers 58 views

The synchronous speed of an 8 pole induction motor supplied power from a 50 Hz source will be ?

asked Dec 31, 2017 in Electrical Engineering by Quiz
1 answer 26 views

The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

asked Jun 18, 2018 in Amplifier by Shimroz123
1 answer 14 views

The gain of an FET amplifier can be changed by changing: (1) rm (2) gm (3) Rd (4) None of these

asked May 28, 2018 in Amplifier by Shimroz123
1 answer 24 views

The gain of an ideal amplifier must be

asked Apr 26, 2018 in Control System by Shimroz123
1 answer 22 views

If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

The effect of a finite gain of an operational amplifier used in an integrator is that (A) it would not integrate (B) the slope of the output will vary with time (C) the final value of the output voltage will reduce (D) there will be instability in the circuit

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
0 answers 10 views

A SCR has an anode supply of sine voltage 200V rms, 50 Hz applied through a 100Q resistor and fired at an angle of 60°. Assuming no voltage drop, the rms value of the output voltage is : (A) 89,7 V (B) 126.7 V (C) 166.7 V (D) 288.28 V

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 32 views

The eddy current loss in an AC motor is 100 watts at 50 Hz. Its losses at 100 Hz will be: (A) 25 watts (B) 59 watts (C) 100 watts (D) 400 watts

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 46 views

In a differential amplifier the differential voltage gain is 500 and the common mode voltage gain is 0.5. The CMRR in dB is (a) 80 (b) 60 (c) 30 (d) 20

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 31 views

In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the (A) applied load (B) internal compensation (C) impedance of the source (D) power dissipation in the chip

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 43 views

As we know when there is a joint in optical fiber then there will be some loss then this loss be minimized by  a. Using index matching fluid in the gap b. Making V-grooved splicing c. Both (a)and (b) d. Making carefully polishing

asked May 17, 2018 in Telecommunication Engineering by Shimroz123
1 answer 16 views

The number of poles in a phase induction motor at 50 Hz and running at 1500 rpm will be?

asked Mar 26, 2018 in Induction Machine by Shimroz123
1 answer 26 views

lf slip of an induction machine is 0.02 and the stator supply frequency is 50 Hz, what will be the frequency of the rotor induced e.m.f.? (A) 10 Hz (B) 50 Hz (C) 1 Hz (D) 2500 Hz

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

The voltage gain of a common base amplifier depends on  1. Load resistor RL 2. input resistance of transistor 3. Ac alpha 4. All the above 

asked May 13, 2018 in Amplifier by Shimroz123
1 answer 70 views

The voltage gain of a common -source JFET amplifier depends up on its  (1) Input impedance (2) Amplification factor (3) Dynamic drain resistance (4) Drain load resistance

asked Apr 30, 2018 in Power Electronics by Shimroz123
1 answer 24 views

The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is  (A) The active device itself (tube, or transistor)  (B) stray shunt capacitance Cs  (C) the grid leak resistance Rg  (D) coupling capacitor Cc

asked May 12, 2018 in Amplifier by Shimroz123
1 answer 29 views

if voltage is 230 Volts , frequency is 50 Hz and current is 1 ampere then what will be the resistance?

asked Dec 4, 2017 in Electrical Engineering by Quiz
1 answer 13 views

The gain margin of a system is 0 dB. It represents a   (a) Stable system (b) Unstable system (c) Marginally stable system (d) Conditionally stable system

asked May 13, 2018 in Control System by Shimroz123
1 answer 26 views

A unity negative feedback control system is found to have a gain margin of 20 dB. The Nyquist plot of the system (A) crosses the real axis at +0.1 (B) crosses the real axis at -0.1. (C) crosses the imaginary axis at -0.1 (D) crosses the imaginary axis at +0.1

asked Apr 28, 2018 in Control System by Shimroz123
1 answer 78 views

 If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be A) 0.98 B) 0.41 C) 59 D) 55  

asked Jun 18, 2018 in Bipolar Junction Transistor by Shimroz123
0 answers 8 views

In a second order system the value of resonant peak will be unity when the damping ratio has a value of  A) Zero B) Unity C) 0.707 D) 0.414

asked Apr 9, 2018 in Control System by Shimroz123
1 answer 20 views

The input frequency of a bridge rectifier is 50 its output frequency will be  1. 25 Hz 2.50 Hz 3.75 Hz 4. 100 Hz

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 24 views

An A.C current is given by i=100sin100. It will achieve a value of 50 A after (1) 1/600 sec (2) 1/300 sec (3) 1/1800 sec (4) 1/900 sec 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

The closed loop gain of an OPAMP is dependent upon, whether the OP AMP is used : -  a) in inverting mode b) in non -inverting mode c) is independent of the fact whether the input is connected to inverting or non -inverting terminal d) is depending upon the fact whether the input is connected to inverting or non -inverting terminal

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
1 answer 47 views

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

asked Apr 25, 2018 in Instrumentation and control by Shimroz123
1 answer 8 views

Define gain and bandwidth of an amplifier.

asked Sep 5, 2018 by Shimroz123
1 answer 34 views

If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is (a) – 13.3 (b) 200 (c) 8 (d) 10 

asked May 25, 2018 in Amplifier by Shimroz123
0 answers 12 views

With the introduction of negative feedback, the gain—bandwidth product of an amplifier  A) Becomes infinity B) Increases C) Decreases D) Remains constant

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is A) Manganin wire of 20 m Ω B) Constantan wire of 20 m Ω C) Manganin wire of 25 m Ω D) Constantan wire of 25 m Ω

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 20 views

A change of 4% in the supply voltage to an induction motor will produce a change of approximately

asked May 8, 2018 in Electrical Machine by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...