# When two alternators are operating in parallel, the cause for circulating current is

11 views
When two alternators are operating in parallel, the cause for circulating current is

(A) increase in the excitation of one machine

(B) increase in the driving torque of one machine

(C) reduction in angular velocity of one machine

(D) identical speed/load characteristics of both machines

When two alternators are operating in parallel, the cause for circulating current is

(A) increase in the excitation of one machine

(B) increase in the driving torque of one machine

(C) reduction in angular velocity of one machine

(D) identical speed/load characteristics of both machines

## Related questions

When two alternators A and B are operating in parallel, the increase in steam supply to alternator A will cause the active power output of (1) Alternator A to be decreased and alternator B to be increased (2) Alternators A and B is not affected (3) Alternators A and B is increased (4) Alternator A to be increased and alternator B to be decreased

If the excitation of an alternator operating in parallel with other alternators decreased, its: (1) Power factor becomes more leading (2) Output Kw will change (3) Power factor becomes more lagging (4) Power factor becomes unity

When two 100 kΩ resistors are connected in parallel, net resistance is

Two parallel conductors are separated by a distance, d carrying a current, I in the same direction. The magnetic field along a line running parallel to the conductors and midway between them is (A) zero (B) proportional to I (C) proportional to d (D) proportional to the permeability of the medium.

Two synchronous generators G1, G2 are operating in parallel and are equally sharing KVAR (Lag) component of load. To shift part of KVAR from G2 to G1, while keeping terminal voltage fixed, the following action must be done

When two synchronous machines are connected in parallel the synchronizing power tends to (A) accelerate the faster machine (B) retard the faster machine (C) retards the slower machine (D) pull the faster machine out of step

How will the total capacitance change, when two capacitors are connected in parallel?

When two transformer of different kVA rating are connected in parallel they share the load in proportion to their respective kVA rating only when their:

A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :  (A) less than 66 kV (B) lie between 66 kV and 110 kV (C) more than 165 kV (D) lie between 110 kV and 165 kV

In a dual converter, the circulating current   (a) allows smooth reversal of load current but increases the response time. (b) allows smooth reversal of load current with improved speed of response. (c) does not allow smooth reversal of load current but reduces response time. (d) flows only if there is no interconnecting conductor.

the division of active power amongst alternators running in parallel depends upon (1) speed-load characteristics of prime mover (2) V-I characteristics of alternator (3) Excitation voltages of alternators (4) Both (b) and (c)

When ‘n’ resistances each of value ‘r’ are connected in parallel, then the resultant resistance is ‘x’. When these ‘n’ resistances are connected in series, total resistance is  (A) n2X (B) X/n (C) n2/X (D) nX2

Two transformers operating in parallel will share the load depending upon their

Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, respectively. Then the system frequency is (A) 50 Hz (B) 51 Hz (C) 51.25 Hz (D) 51.5 Hz

In a balanced 3 -phase 200 V circuit, the line current is 115.5 A. When the power is measured by two wattmeter method, one of the wattmeters reads 20 kW and the other one reads zero. What is the power factor of the load ?

A large transformer operating at no load draws an exciting current Io of 5A, when the primary is connected to a 120 V, 60 Hz source. From a wattmeter test, it is known that iron losses are equal to 180 W. Calculate the reactive power absorbed by the core.  (A) 600 var (B) 572 var (C) 180 var (D) 360 var

Two heater wires of equal length are connected first in series and then in parallel. The ratio of heat generated from series to parallel connection will be (a) 4 : 1 (b) 2 : 1 (c) 1 : 2 (d) 1 : 4

Three lamps are connected in parallel across a 120 Volt source. If one lamp burns out, the remaining two will be: A. Glow dimmer B. Glow brighter C. Not light D. Glow with the same brightness as before

Two 3-phase, Y-connected alternators are to be paralleled to a set of common busbars. The armature has a per phase synchronous reactance of 1.7 Ohm and negligible armature resistance. The line voltage of the first machine is adjusted to 3300 V and that of the second machine is adjusted to 3200 V. The machine voltages are in phase at the ... are paralleled. Under this condition, the synchronizing current per phase will be  (A) 16.98 A (B) 29.41 A (C) 33.96 A (D) 58.82 A

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

In a three-phase system, when the loads are perfectly balanced, the value of neutral current is equal to: A. Zero B. One-third of the maximum value C. Two -third of the maximum value D. The maximum value

If two 3-phase transformers with unequal voltage ratios are connected in parallel, the result is (A) circulating current on no-load (B) no circulating current on no-load (C) dead short-circuit (D) equal no-load secondary emfs

The major cause for creeping in energy—meter is:  (1) Over compensation for friction (2) Vibrations (3) Stray magnetic fields (4) Excessive voltage across the potential coil

When four resistances of 2W 1W; 5W 2W; 10W 5W and 15W 10 W are connected in parallel, the greatest power is absorbed by • 2 W, 1 W • 5 W, 2 W • 10 W, 5W • 15 W, 10 W

When three resistors with unequal values are connected in parallel, _______ A) The current across the resistors is the same  B) The voltage drop across the resistors is the same C) The voltage drops across the resistors is proportional to the resistance of each resistor D) None of these

When n resistances each of value r are connected in parallel, then resultant resistance is x. When these n resistances are connected in series, total resistance is

In a series parallel circuit, any two resistances in the same current path must be in?

In a series RLC circuit that is operating above the resonant frequency, the current : -  a) lags the applied voltage b) leads the applied voltage c) is in phase with the applied voltage d) is zero

When the phase difference between two sinusoidal quantities is 90° they are said to be ______ A) Phase right angle B) Phase quadrature C) Phase sinuright D) None of these

Two transformers with identical voltage ratings are working in parallel to supply common load. The percentage impedance of one transformer is higher compared to that of other. The load sharing between the two transformer will: (1) Be proportional to their percentage impedance (2) Be independent of their percentage impedance (3) Be inversely proportional of their respective impedance (4) Depend on the resistance to leakage reactance ratio of each transformer

A 3-phase induction motor is running at slip ‘s’. If its two supply leads are interchanged, then the operating slip at that instant will be:

When one leg of parallel circuit is opened out the total current will?

“In all cases of electromagnetic induction, an induced voltage will cause a current to flow in a closed circuit in such a direction that the magnetic field which is caused by that current will oppose the change that produces the current” is the original statement of

Consider a circuit with four 10 Ω resistors connected in parallel and the current flowing through the circuit is 5 A. What will be the current if the above 4 resistors are connected in parallel? A) 5 A B) 50 A C) 500 A D) None of these

What is the nature of supply current in parallel RC circuit with reference to the voltage?  (A) In phase (B) Lags by 90 degree (C) Leads by 90 degree (D) Compensates and becomes zero

For a CE amplifier, operating current is 1mA, load resistance is 5 kOhm.The forward bias capacitance is 50 nF and reverse bias capacitance is 10 nF. Total input capacitance in nF is around  A) 40 B) 60 C) 500 D) 2000

Which rotor is use for high speed in turbo alternators?

The condition for parallel operation of two inverters is • Amplitude of voltages should be same. • Frequency of voltages should be same. • Both the voltages should be in same phase. • All the three above.

Transformer voltage is maximum when two coils are (1) Normal to each other (2) Aligned along the same axis (3) 600 away from each other (4) 2700 away from each other

Two transformers are to be operated in parallel such that they share load in proportion to their kVA ratings. The rating of the first transformer is 500 kVA ratings. The rating of the first transformer is 500 kVA and its pu leakage impedance is 0.05 pu. If the rating of second transformer is 250 kVA, its pu leakage impedance is  (A) 0.20 (B) 0.10 (C) 0.05 (D) 0.025