Can you help by answering this question?

What does file format GIF stands for

19 views
in Electrical Engineering by
A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively

(A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

1 Answer

0 votes
by

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively 20, 50 Hz

Related questions

1 answer 16 views

A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be:

asked May 22, 2018 in Electrical Engineering by Shimroz123
0 answers 37 views

A balanced Delta connected load supplied with 440 V 50 Hz three phase AC supply has R=10 Ohm and L=0.6 mH in is each arm. Calculate line and phase current, active power.

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
0 answers 18 views

A parallel combination of capacitance C and resistance R is connected in series with inductance L and small resistance r. Under what condition will the circuit be non-reactive?  (A) C=LR (B) C=LR2 (C) C=L/R2 (D) C=L/R

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

The coefficient of coupling between two coils is 0.45. The first coil has an inductance of 75 mH and the second coil has an inductance of 105 mH. What is the mutual inductance between the coils?  (1) 3.54 mH (2) 7.88 mH (3) 39.9 mH (4) 189.3 mH

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 5 views

As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is A) 25 A B) 50 A C) 100 A D) 200A

asked May 20, 2018 in Network Analysis by Shimroz123
0 answers 11 views

Series resistance required to read 0-250 V with a moving coil instrument of internal resistance 2 ohm and full scale deflection of 50 mA is (a) 49998 Ω (b) 4998 Ω (c) 498 Ω (d) 49.8 Ω

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 25 views

A choke coil having resistance RΩ and of inductance L Henry is shunted by a capacitor of C farads. The dynamic impedance of the resonant circuit would be:  (A) R/LC (B) C/RL (C) L/RC (D) 1/RLC 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

The power consumed by a coil is 300 W when connected to a 30 V dc source and 108 W when connected to a 30 V ac source. The reactance of the coil is

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
1 answer 14 views

A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 83 views

There resistors of 3Ω, 10Ω, and 15Ω are connected in parallel to a 30 V circuit the current that will flow through the 3Ω resistor is 

asked Mar 29, 2018 in Electronics Engineering by Shimroz123
0 answers 22 views

In a series RLC circuit, the rms value of voltage across the resistor is 30 V, across the inductor is 60 V and across the capacitor is 20 V. The rms supply voltage would be (A) 110 V (B) 10 V (C) 220 V (D) 50 V

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 33 views

Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply. The potential difference across 60 watt lamp will be: A) 195 volt B) 220 volt C) 245 volt D) 440 volt

asked Jun 4, 2018 in Electrical Engineering by Shimroz123
0 answers 33 views

A carrier signal of 600 V rms with 75% amplitude modulation is applied to 75 ohm antenna. The total side band power (in watts) is  A) 4800 B) 450 C) 950 D) 1350 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 22 views

What is the charge on each capacitor when a 150 V is applied across two capacitors with values 5 μF and 10 μF, connected in series? A) 500 μC B) 0.5 μC C) 0.5 C D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across the diode? a) 0.3V b) 0.7V c) 0.9V d) 1.4V

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 18 views

A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is (A) 9997 Ω (B) 10000 Ω (C) 997 Ω (D) 10003 Ω

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 47 views

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

asked Apr 25, 2018 in Instrumentation and control by Shimroz123
0 answers 13 views

A switch is connected in between a 12V battery and an uncharged capacitor and a 1 K Ohm resistor. At the time instant when the switch is closed, the voltage across the capacitor is :  A) 6V B) 12v C) 0V D) 24V

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 80 views

Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

In an AC circuit, the voltage across R, L and C are 30 V, 60 V and 20 V respectively. The applied voltage is (A) 70 V (B) 50 V (C) 60 V (D) 100 V

asked May 12, 2018 in Electrical Engineering by Shimroz123
1 answer 28 views

Two light bulbs are connected in series across a 120 V battery. Bulb 1 uses 40 W of power and Bulb 2 uses 20 W of power. If bulb 1 alone is connected to the 120 V source, then it will consume (A) 90 W (B) 80 W (C) 60 W (D) 180 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

A dynamometer type wattmeter with its voltage coil connected across the load side of instrument reads 250 W. If the load voltage be 200 V, what power is being taken by load? The voltage coil has resistance of 2000 Ω. (1) 200 W (2) 215W (3) 230 W /(4) 245 W

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

The induced voltage across a coil with 250 turns that is located in a magnetic field and is changing at a rate of 8 Wb/s is A. 1,000 V B. 2,000 V C.31.25 V D. 3,125 V

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 52 views

A 220 kV, 3 phase transmission line is 60 km long. The resistance is 0.15 ohm / km and the inductance is 1.4 mH / km. Use the short line model to find the power at the sending end when the line is supplying a three phase load of 300 MVA at 0.8 pf lagging at 220 kV.  (A) 5.58MW (B) 80MW (C) 85.58MW (D) 74.42 MW 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

A network consists of several inductances connected in parallel. The equivalent inductance of the network is given by (A) the sum of the individual inductances. (B) the reciprocal of the sum of the individual inductances. (C) the sum of the reciprocals of individual inductances. (D) the reciprocal of the sum of reciprocals of individual inductances.

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

A 100 turn coil has an inductance of 6 mH. If the number of turns is increased to 200, all other quantities remaining the same, the inductance will be:

asked May 22, 2018 in Inductance by Shimroz123
1 answer 10 views

A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is

asked May 15, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

A capacitor and coil in parallel is called

asked May 14, 2018 in Electronics Engineering by Shimroz123
1 answer 24 views

When both the inductance and resistance of a coil are doubled the value of?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 440 views

A 220 V, 200 W bulb and a 220 V, 100 W bulb are connected in series across a 220 V supply, the power consumed by them will be (a) 33.3 W (b) 66.6 W (c) 100 W (d) 300 W

asked May 25, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

A resistance of 3.3 M ohms is connected across a 500 V source. The resulting current is approximately? A.15.1 μA B.151 μA C.66 mA D.660 mA

asked May 15, 2018 in Basic concepts by Zeeshan
1 answer 16 views

When an additional resistor is connected across an existing parallel circuit, the total resistance: A. remains the same B. decreases by the value of the added resistor C. increases by the value of the added resistor D. decreases

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 49 views

An A.C. voltage is impressed across a pure resistance of 3.5 ohms in parallel with a pure inductance of impedance of 3.5 ohms?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

Four inductors each of inductance 1mH are connected in parallel and this combination is connected in series with two inductors each of inductance 1mH. Calculate the equivalent inductance?

asked May 15, 2018 in Inductor by Shimroz123
1 answer 34 views

Two coils connected in series have resistance of 600 ohm and 300 ohm and temperature coefficients of 0.1% and 0.4% respectively.The resistance of the combination at 50oC will be 

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: A. 0 V B. 1.2V C. 6V D. 0.6V

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 28 views

Consider a circuit with four 10 Ω resistors connected in parallel and the current flowing through the circuit is 5 A. What will be the current if the above 4 resistors are connected in parallel? A) 5 A B) 50 A C) 500 A D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 4 views

What is the value of Inductance of a coil that induces 20 V when the current through the coil changes from 12 to 20 A in 2 seconds? A. 2 H B. 3 H C. 4 H D. 5 H 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

A diode D, resistor R and inductor L and a switch S are connected in series.When a voltage V is applied across the circuit and switch is put on, the voltage across L changes as  A) V(1-exp(-t R/L)) B) Vexp(-t R/L) C) Ldi/dt +Ri D) V(1-t R/L)

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 17 views

What is the equivalent resistance of a network having 5 resistors of each 10ohm connected in parallel?  (A) 10 Ohms (B) 50 Ohms (C) 500 Ohms (D) 2 Ohms 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is:

asked May 22, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 10 views

When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly   (A) 0.19 (B) 0.81 (C) 0.97 (D) 1.19

asked May 17, 2018 in Electronics communication by Shimroz123
0 answers 27 views

A Reactor having an inductive reactance of 4 ohm is connected to the terminals of a 120 V AC generator. Calculate the power associated with the reactor.  (A) 3.6 kvar (B) 30 kvar (C) 7.2 kvar (D) 4.16 kvar 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current? A. 30 A/s B. 20 A/s C. 10 A/s D. none of these

asked Apr 12, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...