# With the knowledge of the state variable representation of a plant the transfer function of the plant

19 views
With the knowledge of the state variable representation of a plant the transfer function of the plant

With the knowledge of the state variable representation of a plant the transfer function of the plant can be determined completely

## Related questions

A transfer function has a second order denominator and constant gain in the numerator

Draw a labeled block diagram of sine wave generator and state function of each block.

Draw block diagram of microprocessor and state the function of each block.

Write function of control rods in nuclear power plant.

State function of i) Ceiling rose ii) Conduit

The state equations in the phase variable canonical form can be obtained from the transfer function by (a) Cascade decomposition (b) Direct decomposition (c) Inverse decomposition (d) Parallel decomposition

The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque  (1) Decreases (2) Increases (3) Remains constant (4) None of the above

State maximum power transfer theorem for DC circuit.

In a self-controlled synchronous motor fed from a variable frequency inverter  (1) the rotor poles invariably have damper windings  (2) there are stability problems  (3) the speed of the rotor decides stator frequency  (4) the frequency of the stator decides the rotor speed

Advantages of Variable Frequency Drive (VFD)

The reactive power transfer over a line mainly depends on

The steady state error of the system can be minimized by

State the different types of engines in diesel power plant.

The transfer of energy for reaction turbines is based on _______ A) Newton’s first law B) Newton’s second law C) Newton’s third law D) All the above

For maximum transfer of power, internal resistance of the source should be?

For high efficiency of transfer of power, internal resistance of the source should be?

Explain following techniques related to energy conservation in transmission and distribution system. (i) By balancing phase currents (ii) Variable technical losses (I2R losses).

State the function of cooling tower and condenser in thermal power station.

State the function of superheater and economizer.

State the location and function of i) Economizer ii) Feed water heater.

State the function of former and control spring in PMMC instrument.

State the function of controlling torque in electrical measuring instrument.

State the function of controlling torque. Write two types of it.

In order to regulate steady state error to zero, in a negative feedback control system, one employs

State why nuclear power plants are used as base load plants and diesel power plants as a peak load plant.

State any four advantages and four disadvantages of diesel electric power plant.

State any four factors for selection of hydro power plant site.

State any four factors for selection of site of wind power plant.

State any four factors for selecting location of nuclear power plant.

_______ electric power is the most common method used by electrical grids to transfer power.  (A) One-phase (B) Two-phase (C) Three-phase (D) None of the above

State function of starter and ELCB. (Earth Leakage Circuit Breaker)

State function of Busbar and which material is used for busbar?

Knowledge of Transfer Function is necessary for the calculation of: - a) The Time Constant b) The output for a given input c) The steady state gain d) The order of the system

Transfer switch

Maximum Power Transfer Theorem 1

Explain data transfer mechanism in I2C protocol. Compare it with CAN and USB protocol based on bit rate and area of applications.

The capital cost of a power plant depends on  (1) Total installed capacity only. (2) Total number of units only. (3) Total installed capacity and number of units as well. (4) Neither the installed capacity nor number of units

Compare base load plant with peak load plant on any two points.

The function of a brush and commutator arrangement in a dc motor is to  (1) produce unidirectional torque (2) produce unidirectional current in the armature (3) help in changing the direction of rotation of the armature (4) reduce sparking

The necessary and sufficient condition for a rational function of, T(s) to be driving point impedance of an RC network is that all poles and zeros should be

The function of a surge tank is to  (1) produce surge in the pipeline (2) relieve water hammer pressure in the penstock (3) supply water at constant pressure (4) none of above