# A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum

446 views
A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is

(A) 28.2 mm (B) 26.4 mm

(C) 24.4 mm (D) 22.0 mm

A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is 22.0 mm

by

## Related questions

A single core lead sheathed cable with two dielectrics of permittivity 4 and 3, respectively, are subjected to same maximum stress. If the conductor diameter is 1.5 cm, the outer diameter of the first dielectric is (A) 1.125 cm (B) 1.5 cm (C ) 2 cm (D) 8 cm

write short notes on single phase system.

What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be?

How does a single phase induction motor work?

A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

What is line voltage and phase voltage? Draw balanced three phase star connected system. Show all the voltages and currents.

A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he

For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is

Describe the gate circuit for a single phase full converter.

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W

Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

When a V-V three phase transformer system is converted into a Δ-Δ system, increase in capacity of the system is (A) 86.6% (B) 50% (C) 57.7% (D) 73.2%

three phase to single phase cycloconverter

What are the five types of single phase motors used in the industry?

explain the working of single phase induction motor.

Phase margin is the amount of angle to make the system  (1) Oscillatory (2) Stable (3) Unstable (4) Exponential

State any four advantages of three phase over single phase.

An unexcited single phase synchronous motor is ?

Explain the principle of ON-OFF control and phase control of AC voltage controller with suitable circuit and waveforms.

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

Explain power in single phase AC circuit.

single phase full converter

Single Phase Induction Motor

The permissible voltage variation in transmission and distribution system is:  (A) ± 0.1% (B) ± 1% (C) ±10% (D) ± 25%

Write the relation between phase and line current, phase and line voltage for Star connection.

Explain following techniques related to energy conservation in transmission and distribution system. (i) By balancing phase currents (ii) Variable technical losses (I2R losses).

In an alternator at lagging power factor the generated voltage per phase as compared to that at unity power factor?

What is the difference between a line voltage and low voltage control system?