# In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR

33 views
In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in

(A) voltage notching (B) harmonic distortion

(C) voltage sag (D) voltage swell

In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in voltage notching

## Related questions

A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

The SCR would be turned OFF by voltage reversal of applied anode-cathode ac supply frequency of A) 10 kHz B) 10 Hz C) 5 kHz D) 5 Hz

Describe the gate circuit for a single phase full converter.

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) inversely proportional to α and Φ (C) directly proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole)  (A) has q -axis current only (B) has d -axis current only (C) has both d and q axis currents (D) cannot be divided between q and d axis currents

single phase full converter

List any two methods of reactive power measurement in 3 phase circuit.

How is the GTO turned off? A) By using a commutation circuit B) By applying reverse gate pulse C) By using a latch-up circuit D) By reverse anode current pulse

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

A 100-watt light bulb turned on for 8 hours uses :  (A) 800 Wh (B) 0.8 kWh (C) 8 kWh (D) None of the above

Define phase sequence of three phase supply with waveforms. What is normal phase sequence? Which 3 standard colours are used to denote the phase sequence?

An inductor is connected in series with SCR to protect it from A) Excessive high voltage B) Excessive high dv/dt C) Excessive high di/dt D) Excessive large forward current

Damper winding is provided in 3 phase synchronous motors to :

Define balanced and unbalanced load in three phase circuit.

Explain power relations in three phase circuit.

Explain power in single phase AC circuit.

In a thyristor D.C. chopper, which type of commutation results in best performance ?

The direction of rotation of an inverter fed 3-phase ac motor is reversed by (A) a mechanical reversing switch (B) reversing the input dc link voltage (C) operating the inverter as a rectifier (D) changing the sequence of switching

Explain the principle of ON-OFF control and phase control of AC voltage controller with suitable circuit and waveforms.

The sequence components of current of a single-phase load connected to a 3-phase system are (A) equal positive and negative sequence components (B) equal positive, negative and zero sequence components (C) vector sum of sequence currents is zero (D) algebraic sum of sequence currents is zero

Circuit turn-off time of an SCR is defined as the time  (A) taken by the SCR turn to be off (B) required for the SCR current to become zero (C) for which the SCR is reverse biased by the commutation circuit (D) for which the SCR is reverse biased to reduce its current below the holding current

How do you test an SCR?

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

State any four applications of three phase circuits.

What is Analog to Digital Converter (ADC) ?

What is the difference between a thyristor and an SCR?

The percent resolution of an 8 -bit D/A converter is

Digital to Analog Converter (DAC)

The power consumed in a circuit element will be least when the phase difference between the current and voltage is?

Two 3-phase transformers cannot be operated in parallel, if their :  (A) kVAs are different (B) phase sequences are different (C) % impedances are different (D) voltage ratios are different

Turn-on time of an SCR in series with RL circuit can be reduced by   (a) Increasing circuit resistance R (b) Decreasing R (c) Increasing circuit inductance L (d) Decreasing L

Which of the following 3-phase connection of a transformer causes interference with the neighbouring communication lines:  (A) Delta-Star (B) Star-Delta (C) Delta-Delta (D) Star-Star

The speed of a 2-pole, 3-phase stepper motor operated by 1200 pulses/min (A) 100 rpm (B) 200 rpm (C) 400 rpm (D) 800 rpm

Sparking occurs when a load is switched off because the circuit has high?

An SCR without any external connections is considered as (A) two diodes in series (B) three diodes in series (C) two n-p-n transistors in series (D) two p-n-p transistors in series

During 3-phase short circuit on a unloaded alternator, the dc component may be zero in (1) One phase only (2) Any two phases (3) All three phases (4) None of the above

To turn a conducting SCR to off state, it is necessary to make : -  a) anode current less than holding current b)gate current zero  c) anode voltage less than break over voltage  d) gate voltage zero