When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially

26 views
When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially short circuited because

(A) Cables have a low value of capacitance which draws a high value of charging current

(B) Cables have a low value of initial resistance

(C) Cables have a high value of capacitance which draws a high value of charging current

(D) Cables have a low value of capacitance and initial resistance

When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially short circuited because Cables have a high value of capacitance which draws a high value of charging current

Related questions

Name the method used to measure following resistances:- (i) Low resistance (ii) Medium resistance (iii) Insulation resistance (iv) Earth resistance.

While testing cables the galvanometer used should be initially short-circuited in order to protect it from sudden initial inrush currents as the cable have:

If the insulation resistance of a cable of length 10 km is 1 mega ohm, its insulation resistance for 50 km length will be

What is the lowest acceptable insulation resistance for a cable?

What is an insulation resistance test?

For maximum transfer of power, internal resistance of the source should be?

Give the classification of the errors used in measuring instrument & state the reason for their occurrence.

What should be the ideal resistance of ammeter ?

The normal value of the armature resistance of a d.c. motor is?

List out any four effects of electric current used in measuring instruments & write name of meter working on it.

In a transformer the resistance between its primary and secondary should be?

The thickness of insulation provided on the conductor depends on?

Define the following terms as referred to battery. a) E.M.F b) Internal resistance c) Ah efficiency d) WAh efficiency

The insulation on a current carrying conductor is provided?

State the function of controlling torque in electrical measuring instrument.

What do you mean by insulation coordination?

What is double or reinforced insulation?

What is basic insulation level?

When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a low resistance initially and then slowly came to infinity position. This shows that capacitor is ?

When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But when the same voltage is measured using a Permanent Magnet Moving Coil (PMMC) voltmeter, the voltmeter reading shows 0.99 V. If the resistance of the voltmeter is 1100 Ohm , the internal resistance of the battery, in Ohm , is (A) 150 (B) 100 (C) 50 (D) 200

Resistance grounding is normally used for :  (A) high voltage long over head transmission lines  (B) low voltage short over head transmission lines  (C) extra high voltage long over head transmission lines  (D) all the above

State two purposes of calibration of measuring instruments.

List three types of errors in measuring instruments. Give reasons of occurring for any one of them.

Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

Explain the essential toques in analog type measuring instruments.

Name the different torque and their function in measuring instrument.

What arc the errors occurring in measuring devices due to stray magnetic field and temp '? Explain how to compensate them.

The insulation resistance of earth of an installation should be nearly: -  a) 0.1 M ohm b) 0.2 M ohm c) 0.5 M ohm d) 1 M ohm.

A megger is to measure insulation resistance of a cable. The cable should be connected to   (a) Battery (b) DC supply (c) AC supply (d) No supply

What happens to the resistance of a wire when its length as well as the cross-sectional area are doubled? A) It doubles B) It becomes 4 times C) It becomes 2π times D) It remains the same

When both the inductance and resistance of a coil are doubled the value of?

A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is (A) 1 Ω (B) 1.001 Ω (C) 0.5 Ω (D) 10 Ω

The transducer with negative temperature co-efficient of resistance is (A) Thermistor (B) Resistance Thermometer (C) Strain Gauge (D) Thermocouple

Define following terms related to measuring instruments: i) Sensitivity ii) Selectivity.

Explain magnetic effect employed in measuring instrument.

Describe systematic errors in measuring instruments.