The self inductance of a coil can be measured using

18 views
The self inductance of a coil can be measured using

(A) Wien’s Bridge (B) Schering Bridge

(C) Anderson’s Bridge (D) Wheatstone Bridge

The self inductance of a coil can be measured using Anderson’s Bridge

Related questions

The inductance of a coil can be increased by?

lt the length, number of turns and area of a coil are  doubled, the inductance of the coil

The initial rate of rise of current through a coil of inductance 10 H when suddenly connected to a D.C. supply of 200 V is_______Vs.

Self inductance formula

Self induced voltage across an inductance

Inductance of a coil Varies?

Inductance of coil?

When the voltage across a battery is measured using a D.C potentiometer, the reading shows 1.08 V. But when the same voltage is measured using a Permanent Magnet Moving Coil (PMMC) voltmeter, the voltmeter reading shows 0.99 V. If the resistance of the voltmeter is 1100 Ohm , the internal resistance of the battery, in Ohm , is (A) 150 (B) 100 (C) 50 (D) 200

A synchronous motor can be made self starting by providing?

When both the inductance and resistance of a coil are doubled the value of?

A suspension type insulator has 2 units with self capacitance C and ground capacitance of 0.2 C. Each unit can withstand for a maximum voltage of 11 kV. Its string efficiency is  (A) 78% (B) 82% (C) 80% (D) 84%

Dielectric loss in a capacitor is best measured by (A) Wien Bridge (B) Schering Bridge (C) Anderson Bridge (D) Heaviside-Campbell Equal Ratio Bridge

Liquid flow rate is measured using (A) a pirani gauge (B) a pyrometer (C) an orifice plate (D) a bourdon tube

True value has been 50 whereas measured value is 40 then the percentage error in the reading will be ______.  (A) 20% (B) 40% (C) 50% (D) 30%

A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is (A) 1 Ω (B) 1.001 Ω (C) 0.5 Ω (D) 10 Ω

A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned in a uniform radial flux density of 200 mT. The coil carrier current capacity is 50 mA. The torque on the coil is

For 11kV line the inductance per km per phase will be of the order of:  (A) 1 H (B) 0.1 H (C) 1 mH (D) 0.1 mH

The load of a consumer is generally measured in terms of : (A) Volts (B) Amperes (C) Ampere hour (D) kW

The bridge method commonly used for finding mutual inductance is (A) Heaviside Campbell bridge (B) Schering bridge (C) De Sauty bridge (D) Wien bridge

Explain the term self induced EMF with a neat diagram.

In a battery, the difference between the no-load voltage and the measured voltage output is called ________ A) Internal voltage B) Internal resistance C) External resistance D) All the above

The power consumed by a balanced 3-ph load is measured by two-wattmeter method. The meter readings are 8 kW and 4 kW. The power factor of the load is (A) zero (B) 0.5 (C) between zero and 0.5 (D) between 0.5 and unity

How is a three phase cage induction motor self starting?

What is self biasing of transistor?

The self GMD method is used to evaluate

If both the number of turns and core length of an inductive coil are doubled, then its self inductance will be (a) halved (b) doubled (c) quadrupled (d) unaffected

Permanent magnet moving coil instruments are used for

The purpose of the restraining coil in a biased differential relay is  (A) To reduce CT saturation during fault.  (B) To increase the sensitivity of the relay.  (C) To match the transformation ratio.  (D) To limit the spill current through the relay during heavy external fault.

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%