# The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the

29 views
The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating anode voltage is reduced to half of its previous value. Then, the vertical deflection of the beam on the screen would become

(A) 64 mm (B) 32 mm (C) 8 mm (D) 1 mm

The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating anode voltage is reduced to half of its previous value. Then, the vertical deflection of the beam on the screen would become 32 mm

## Related questions

The Lissajous pattern on the screen of a CRO is an ellipse with major axis in quadrant 2 and quadrant 4. Then the phase difference between two signals Can be :  (A) 270° (B) 210° (C) 180° (D) 300°

lf the wire which is vertical to this page has electron flow downwards the conductor will have

On the ladder resting on the ground and leaning against a smooth vertical wall, the force of friction will be?

On a ladder resting on smooth ground and leaning against vertical wall, the force of friction will be?

A heavy ladder resting on floor and against a vertical wall may not be in equilibrium, if?

What is the charge and mass of an electron?

The ratio of mass of proton to that of electron is nearly?

Define : i) Diffuse radiation ii) Beam radiation ii) Insolation iv) Solar constant

List any four measure knobs on front panel on CRO.

In a metal conductor, what is a free electron?

What is vertical sag?

Deflection of electron beam in a CRT is  A) Inversly proportional to length of deflecting plates B) Directly proportional to distance between plates C) Inversly proportional to deflecting potential D) Inversly proportional to accelerating potential

The time base signal in Cathode Ray Oscilloscope (CRO) is  (1) A square wave signal (2) A sawtooth signal (3) A triangular wave signal (4) A sinusoidal signal

The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is 2 sin ωt, the Y–plate input is (1) 2 sin ωt (2) 2 sin (ωt + 45°) (3) 2 sin (ωt – 45°) (4) 22 sin ωt + 45°)

List any two applications of CRO.

Draw block diagram of CRO. Write function of each block.

The trace on an oscilloscope continually moves to the right of the screen when  (a) the sweep is triggered. (b) the sweep period is larger than the signal period. (c) the sweep period is smaller than the signal period. (d) there is no weep.

The charge on an electron is known to be 1.6 x 10-19 coulomb. In a circuit the current flowing is 1 A. How many electrons will be flowing through the circuit in a second?

In a Traveling-wave Tube, the velocity of electron beam with respect to the axial velocity of RF field is kept...  A) Lower B) Higher C) Equal D) Any of these

If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of deflection plates is 2 cm, the distance between the plates is 1 cm and accelerating voltage is 500 V, deflection sensitivity is   (a) 33.2 V/cm (b) 0.03 cm/V (c) 66.4 V/cm (d) 0.015 cm/V

Lissajous pattern obtained on a CRO screen is a circle. Frequency of two signals are   (a) Equal (b) Unequal (c) Zero (d) Infinity

In a CRO, the quantity to be measured is applied across  (1) focusing electrodes (2) cathode (3) Y-plates (4) X-plates

Lissajons figures asppear on CRO screen (a) when two sine waves of same frequency input signals. (b) depend on amplitude of two input signals. (c) depend on phase of two input signals. (d) used to measure harmonics.

A Lissajous pattern on an oscilloscope has 5 horizontal tangencies and 2 vertical tangencies. The frequency of the horizontal input is 1000 Hz. What is the frequency of the vertical input?  (A) 400 Hz (B) 5000 Hz (C) 4000 Hz (D) 2500 Hz

In a CRO which of the following is not a part of electron gun: (1) Cathode (2) Grid (3) Accelerating anode (4) X–Y plates

The two inputs of a CRO are fed with two stationary periodic signals. In the X-Y mode, the screen shows a figure Which changes from ellipse to circle and back to ellipse with its major axis changing orientation slowly and repeatedly. The following inference can be made from this  A) The signals are not sinusoidal ... but not equal C) The signals are sinusoidal with their frequencies very close but not equal D) There is a constant but small phase difference between the signals

Number of comparators required for an 8 bit flash ADC is: (1) 8 (2) 16 (3) 255 (4) 256

Velocity of an electron (in km/S) starting at rest and travelling to a point 100 V above the starting potential is around  A) 3600 B) 4000 C) 5100 D) 6000

In a weighted-resistor digital-to-analog converter with 8-bit input, if the resistance corresponding to the MSB is 2K, what will be the resistance corresponding to the LSB?  (a) 250 Ω (d) 512 KΩ (c) 256 KΩ (d) 25.5 Ω

Consider the following statements with regard to Lissajous pattern on a CRO :  1. It is a stationary pattern on the CRO.  2. It is used for precise measurement of frequency of a voltage signal.  3. The ratio between frequencies of vertical and longitudinal voltage signals should be an integer to have a steady Lissajous pattern.  Which of the above statements is/are correct ?  (a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3

An 8 pole lap wound DC shunt generator is supplying 295A to a load. The field current of the generator is 5A. The current per parallel path is: -  a) 300A b) 200A c) 150A d) 37.5A

The synchronous speed of an 8 pole induction motor supplied power from a 50 Hz source will be ?

The inductance of a long solenoid of length 1000 mm wound uniformly with 3000 turns on a cylindrical paper tube of 60 mm diameter is  (A) 3.2 µH (B) 3.2 mH (C) 32.0 mH (D) 3.2 H

Horizontal deflection plates of CRO are placed generally   (a) Horizontal (b) Vertical (c) Diagonal (d) (a) or (b)

The power delivered to a 3-phase load can be measured by the use of two wattmeters only when the  (a) load is unbalanced (b) load is balanced (c) three phase load is connected to the source through three wires (d) three phase load is connected to the source through four wires

The power delivered to a three-phase load can be measured by the use of 2 wattmeter only when the A. Load is balanced B. 3 -phase load is connected to the source through 3 wires C. Load is unbalanced D. 3 -phase load is connected to the source through 4 wires

An 8 pole wound rotor induction motor operating on 60 Hz supply is driven at 1800 r.p.m. by a prime mover in the opposite direction of revolving magnetic field. The frequency of the rotor current is (a) 30 Hz (b) 60 Hz (c) 120 Hz (d) 180 Hz

An aquadog is used in a 'CRO' to collect -  a) Secondary emission electrons b) Primary emission electrons c) Both Primary and Secondary emission electrons d) None of the above

In the case of an instrument reading of 8.3 V with a 0 to 150 voltmeter having a guaranteed accuracy of 1% full scale reading, the percentage limiting error is   (A) 1.810% (B) 0.181% (C)12.45% (D) 0.0018%

An 1.8° step, 4 -phase stepper motor has 40 teeth on 8 poles of the stator. The number of rotor teeth for their rotor will be: (A) 40 (B) 50 (C) 100 (D) 80

Without any additional circuitry, an 8:1 MUX can be used to obtain:  (1) Some but not all Boolean functions of 3 variables (2) All function of 3 variables but none of 4 variables (3) All functions of 3 variables and some but not all of 4 variables (4) All functions of 4 variables

Y –axis in a CRO normally represents

A power system is represented by its system matrix ZBUS (m × m). Now an element is added in power system network without creating a new node. The dimension of the new impedance matrix will be (a) m × m (b) (m + 1) × (m + 1) (c) (m – 1) × (m – 1) (d) (m + 2) × (m + 2)