# An induction type energy meter is found to run fast. Correction for this error can be made by

36 views
An induction type energy meter is found to run fast. Correction for this error can be made by

(B) Voltage compensation.

(C) Moving the brake magnet away from the centre of the disc.

(D) Moving the brake magnet towards the centre of the disc.

An induction type energy meter is found to run fast. Correction for this error can be made by Moving the brake magnet away from the centre of the disc.

## Related questions

List any four errors in induction type energy meter. Give method of compensation for each.

State the function and shape of following parts used in induction type energy meter: i) Series magnet ii) Shunt magnet iii) Al disc iv) Brake magnet

Draw a neat sketch of 1-ph induction type energy meter and write operating principle of it.

Why energy meter is integrating type measuring instrument?

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W

For measurement of radio frequency ac signals __________ type meter is used

What type of meter is used to measure current?

State the meaning of creeping error in 1 phase energy meter.

Explain the “mitigation of power theft” and “faulty meter replacement” for energy conservation techniques to reduce commercial losses.

A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is (A) 2.5 W (B) 5 W (C) 32.5 W (D) 35 W

What is meant by energy meter constant?

Explain energy conservation technique “by improving power quality” for induction motor.

Phantom loading for testing of energy meter is used (A) to isolate the current and potential circuits (B) to increase power loss during testing (C) for meters having low current ratings (D) to test meters having a large current rating for which loads may not be available

With neat diagram explain calibration of energy meter by direct loading method.

Describe principle of operation of Doppler type ultrasonic flow meter with diagram.

Draw the diagram and explain the working of ferrodynamic type frequency meter.

With a neat sketch explain working of 1 phase dynamometer type power factor meter.

Explain working of Weston type frequency meter.

Draw a block diagram of electronic energy meter. Write function of each block.

Draw and describe working of electronic energy meter.

Write any two advantages of digital energy meter.

In the induction type directional over current relay, when a short-circuit occurs in the circuit (A) power flows in reverse direction (B) power flows in normal direction (C) directional power element does not operate (D) over current element is not energized

Energy meter runs slowly even if power is not used. This error is called (a) Speed error (b) Phase error (c) Creeping error (d) None of these

Which type of heater is cheapest to run?

In an induction type energy meter, the steady speed attained by the rotating disc is  1. Proportional to the deflecting torque. 2. Proportional to the resistance of the path of eddy currents. 3. Inversely proportional to the effective readings of disc from its axis. 4. Inversely proportional to the square of brake magnet flux.  Which of the above are correct ?

Generally, Crawling in squirrel cage induction motors is tendency to run stably at speeds as low as (A) One-third of their synchronous speed (B) One-fifth of their synchronous speed (C) One-seventh of their synchronous speed (D) One-ninth of their synchronous speed

In a household single phase induction type wattmeter, the meter can be reversed by: - a) reversing the supply terminals b) reversing the load terminal c) opening the meter connection and reversing either the potential coil terminals or current coil terminals d) opening the meter and reversing the connection of both the potential coil terminals and current coil terminals

The meter which does not have any component in it to provide control torque is (A) Electrodynamometer for current measurement (B) Electrodynamometer for voltage measurement (C) Electrodynamometer for power measurement. (D) Electrodynamometer for power factor measurement.

n-type semiconductor can be made by adding ____ to intrinsic semiconductor (A) Boron (B) Arsenic (C) Carbon (D) Germanium

In a 3-phase slip-ring induction motor, the slip at some speed is 0.05. The speed is reduced by inserting an external resistance in the rotor circuit and the slip is 0.15. If the rotor winding resistance per phase is 0.2 Ω, the external resistance is (A) 0.2 Ω (B) 0.3 Ω (C) 0.4 Ω (D) 0.5 Ω

Write how energy can be stored or generated in each of following : i) solar cell ii) geothermal energy iii) hydrogen energy in biomass.

Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be

A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

Why starter is required for starting an induction motor?