44 views
in Electrical Measurements and Instrumentation by
The meter which does not have any component in it to provide control torque is

(A) Electrodynamometer for current measurement

(B) Electrodynamometer for voltage measurement

(C) Electrodynamometer for power measurement.

(D) Electrodynamometer for power factor measurement.

1 Answer

0 votes
by

The meter which does not have any component in it to provide control torque is Electrodynamometer for power factor measurement.

Related questions

1 answer 26 views

Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

asked Sep 6, 2018 by Shimroz123
1 answer 17 views

A differentiator is not usually used in control system, because it : - (A) reduces damping  (B) increases error  (C) reduces gain margin  (D) increases input noise

asked Apr 30, 2018 in Control System by Shimroz123
1 answer 15 views

Negative feedback in a closed-loop control system DOES NOT (A) reduce the overall gain (B) reduce bandwidth (C) improve disturbance rejection (D) reduce sensitivity to parameter variation

asked Apr 26, 2018 in Control System by Shimroz123
1 answer 74 views

The torque produced in wattmeter is proportional to

asked Apr 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 30 views

The maximum torque which a synchronous motor will develop at rest for any angular position of the rotor, at rated stator supply voltage and frequency, is known as?

asked Mar 20, 2018 in Synchronous machine by Shimroz123
1 answer 26 views

A moving coil of meter has 100 turns, and a length and depth of 10mm and 20mm respectively. It is positioned in a uniform radial flux density of 200 mT. The coil carrier current capacity is 50 mA. The torque on the coil is

asked Apr 29, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 26 views

A unity negative feedback control system is found to have a gain margin of 20 dB. The Nyquist plot of the system (A) crosses the real axis at +0.1 (B) crosses the real axis at -0.1. (C) crosses the imaginary axis at -0.1 (D) crosses the imaginary axis at +0.1

asked Apr 28, 2018 in Control System by Shimroz123
1 answer 116 views

The torque developed by any 3-phase induction motor at 0.8 p.u. slip is (A) Full-load torque (B) unstable torque (C) starting torque (D) break down

asked Apr 28, 2018 in Electrical Machine by Shimroz123
0 answers 18 views

In a particular meter, the deflecting torque is directly proportional to the current flowing through it, the type of meter is (a) moving coil (b) moving iron (c) induction (d) electro-static  

asked May 26, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 37 views

An induction type energy meter is found to run fast. Correction for this error can be made by  (A) Over-load compensation. (B) Voltage compensation. (C) Moving the brake magnet away from the centre of the disc. (D) Moving the brake magnet towards the centre of the disc.

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
3 answers 88 views

What type of meter is used to measure current?

asked Mar 10, 2018 in Electrical Measurements and Instrumentation by Quiz
1 answer 5 views

State the function of controlling torque. Write two types of it.

asked Sep 6, 2018 by Shimroz123
1 answer 15 views

List any four errors in induction type energy meter. Give method of compensation for each.

asked Sep 5, 2018 by Shimroz123
1 answer 19 views

A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is (A) 2.5 W (B) 5 W (C) 32.5 W (D) 35 W

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 32 views

Ideally, the damping torque should be  (1) Proportional to velocity of the moving system and operating current.  (2) Proportional to the velocity of the moving system but independent of operating current.  (3) Independent of the velocity of the moving system and proportional to the operating current.  (4) Independent of the velocity of the moving system and operating current.

asked Apr 30, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 21 views

Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be

asked Apr 29, 2018 in Electrical Machine by Shimroz123
0 answers 15 views

What does an electric meter measure?

asked Mar 10, 2018 in Power quality by Quiz
1 answer 28 views

The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as?

asked Mar 20, 2018 in Synchronous machine by Shimroz123
1 answer 53 views
1 answer 38 views

What is the maximum value of torque angle in synchronous motor?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 9 views

Write any two advantages of digital energy meter.

asked Sep 5, 2018 by Shimroz123
1 answer 17 views

Draw a neat sketch of 1-ph induction type energy meter and write operating principle of it. 

asked Sep 6, 2018 by Shimroz123
1 answer 10 views

List the different methods to produce damping torque.

asked Sep 6, 2018 by Shimroz123
1 answer 24 views

A control system having unit damping factor will give  (1) Oscillatory response (2) Undamped response (3) Critically damped response (4) No response

asked May 1, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 22 views

In a double squirrel cage induction motor, good starting torque is produced as (A) Large current flows through the outer high resistance winding. (B) Large current flows through the inner high resistance winding. (C) Small current flows through the outer high resistance winding. (D) Large current flows through the inner low resistance winding.

asked May 8, 2018 in Electrical Machine by Shimroz123
1 answer 25 views

The standard for long distance analog signal transmission in process control industry is (A) 4-20 mV (B) 0-20 mA (C) 4-20 mA (D) 0-5 V

asked Apr 26, 2018 in Control System by Shimroz123
1 answer 20 views

kWh meter is the electric meter that measures the amount of electrical _________ in kWh that was consumed in the house.  (A) Energy (B) Current (C) Voltage (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W

asked Apr 25, 2018 in Instrumentation and control by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...