22 views
in Switchgear And Protection by
In the induction type directional over current relay, when a short-circuit occurs in the circuit

(A) power flows in reverse direction

(B) power flows in normal direction

(C) directional power element does not operate

(D) over current element is not energized

1 Answer

0 votes
by

In the induction type directional over current relay, when a short-circuit occurs in the circuit power flows in reverse direction

Related questions

1 answer 19 views

Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

asked May 8, 2018 in Electrical Engineering by Zeeshan
1 answer 21 views

In which fault the maximum short circuit current occurs?

asked Mar 19, 2018 in Switchgear And Protection by Shimroz123
1 answer 10 views

State the function and shape of following parts used in induction type energy meter: i) Series magnet ii) Shunt magnet iii) Al disc iv) Brake magnet

asked Sep 6, 2018 by Shimroz123
1 answer 22 views

In induction type directional over current relay the driving torque is due to interaction of magnetic fields derived from (A) current in the potential coil (B) both voltage and current in the relay windings (C) directional element and non-directional element (D) non-directional element and the trip circuit

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

List any four errors in induction type energy meter. Give method of compensation for each.

asked Sep 5, 2018 by Shimroz123
1 answer 17 views

Draw a neat sketch of 1-ph induction type energy meter and write operating principle of it. 

asked Sep 6, 2018 by Shimroz123
1 answer 37 views

An induction type energy meter is found to run fast. Correction for this error can be made by  (A) Over-load compensation. (B) Voltage compensation. (C) Moving the brake magnet away from the centre of the disc. (D) Moving the brake magnet towards the centre of the disc.

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
3 answers 88 views

What type of meter is used to measure current?

asked Mar 10, 2018 in Electrical Measurements and Instrumentation by Quiz
1 answer 15 views

Why does induction motor have high starting current?

asked Mar 15, 2018 in Electrical Engineering by Quiz
1 answer 40 views

If the % reactance upto the fault point is 20%, then the short circuit current will be

asked May 8, 2018 in Switchgear And Protection by Shimroz123
1 answer 41 views

The purpose of the restraining coil in a biased differential relay is  (A) To reduce CT saturation during fault.  (B) To increase the sensitivity of the relay.  (C) To match the transformation ratio.  (D) To limit the spill current through the relay during heavy external fault.

asked May 8, 2018 in Switchgear And Protection by Shimroz123
1 answer 22 views

The surge impedance for over head line is taken as  (1) 10-20 ohms (2) 50-60 ohms (3) 100-200 ohms (4) 1000-2000 ohms

asked May 1, 2018 in Switchgear And Protection by Shimroz123
1 answer 48 views

What is the use of Buchholz relay in transformer?

asked Dec 17, 2017 in Switchgear And Protection by Quiz
1 answer 40 views

To prevent mal-operation of differentially connected relay while energizing a transformer, the relay restraining coil is based with  (1) second harmonic current  (2) third harmonic current  (3) fifth harmonic current  (4) seventh harmonic current

asked Apr 29, 2018 in Switchgear And Protection by Shimroz123
1 answer 45 views

What is the difference between a switch and a relay?

asked Dec 17, 2017 in Switchgear And Protection by Quiz
1 answer 29 views

If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be

asked May 8, 2018 in Switchgear And Protection by Shimroz123
1 answer 53 views

A relay used for protection of motors against overload is :  (A) Impedance relay (B) Electromagnetic attraction type (C) Thermal relay (D) Buchholz's relay

asked May 8, 2018 in Switchgear And Protection by Shimroz123
1 answer 31 views

A relay has a rating of 5 A, 2.2 sec IDMT and a relay setting of 125% TMS = 0.6. It is connected to a supply circuit through a C.T. 400/5 ratio. The fault current is 4000 A. The operating current of the relay is

asked May 3, 2018 in Switchgear And Protection by Shimroz123
1 answer 366 views

A negative sequence relay is used for protection of  (1) Generator (3) Motor (2) Transformer (4) Long Transmission lines

asked May 1, 2018 in Switchgear And Protection by Shimroz123
1 answer 13 views

A solid state relay (A) withstands voltage transients (B) does not require auxiliary dc supply (C) provide low burden on CT and P (D) does not provide earth fault protection

asked Apr 28, 2018 in Switchgear And Protection by Shimroz123
1 answer 28 views

The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole)  (A) has q -axis current only (B) has d -axis current only (C) has both d and q axis currents (D) cannot be divided between q and d axis currents

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 26 views

The operating time of instantaneous relay is

asked May 3, 2018 in Switchgear And Protection by Shimroz123
1 answer 69 views

What is the difference between relay and contactor?

asked May 2, 2018 in Switchgear And Protection by Quiz
1 answer 20 views

Buchholz relay is  (1) located in the conservator tank  (2) located in the transformer tank itself  (3) connected in the pipe connecting main tank of transformer and conservator  (4) installed in the circuit breaker

asked Apr 30, 2018 in Switchgear And Protection by Shimroz123
1 answer 25 views

Reactance relay is normally preferred for protection against

asked Apr 29, 2018 in Switchgear And Protection by Shimroz123
1 answer 59 views

How do relay works ?

asked Dec 30, 2017 in Switchgear And Protection by Quiz
1 answer 23 views

In a single-phase induction motor when the rotor is stationary and voltage is applied to the stator, then (A) the flux is constant (B) the flux first decreases and then increases in the same direction (C) the flux increases and decreases in the opposite direction with the same magnitude (D) current flows through the rotor

asked Apr 28, 2018 in Electrical Machine by Shimroz123
1 answer 18 views

30°, 60° and 90° connections are made in a directional relay to render the relay (A) Sufficient torque under fault conditions (B) Zero torque under fault conditions (C) Current grading (D) Time grading

asked May 12, 2018 in Switchgear And Protection by Shimroz123
1 answer 21 views

Which is the most common type of fault?

asked Mar 19, 2018 in Switchgear And Protection by Shimroz123
1 answer 21 views

The main advantage of AC over DC is:  (A) Conversion flexibility from one voltage level to other (B) AC can be easily converted into DC by using a rectifier (C) AC is easy to maintain & can be easily distributed at long distances (D) All of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
0 answers 13 views

Explain the significance of over modulation.

asked Mar 10, 2018 in Power Electronics by Quiz

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...