24 views
in Power Electronics by
A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is

(A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

1 Answer

0 votes
by

A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

Related questions

1 answer 38 views

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

asked Apr 28, 2018 in Power Electronics by Shimroz123
1 answer 56 views

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) inversely proportional to α and Φ (C) directly proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 41 views

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 33 views

In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in (A) voltage notching (B) harmonic distortion (C) voltage sag (D) voltage swell

asked Apr 28, 2018 in Electronics Engineering by Shimroz123
1 answer 25 views

When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

asked Apr 29, 2018 in Power Electronics by Shimroz123
0 answers 21 views

Describe the gate circuit for a single phase full converter.

asked Mar 11, 2018 in Power Electronics by Quiz
1 answer 22 views

single phase full converter

asked Nov 16, 2017 in Power Electronics by Quiz
1 answer 63 views

Explain the operation of full bridge converters with their different operating modes. State its advantages and disadvantages.

asked Feb 12, 2018 in Unit 2 by Quiz
1 answer 36 views

In voltage source converter based HVDC transmission system the active power is controlled by changing (A) phase angle of the converter ac input voltage (B) supply frequency of the converter ac input voltage (C) magnitude of the converter ac input voltage (D) DC voltage at the inverter terminals

asked Apr 28, 2018 in High voltage engineering by Shimroz123
1 answer 18 views

A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high load inductance. The input displacement factor (IDF) and the input power factor (IPF) of the converter will be  (A) IDF IPF = = 0.867; 0.828 (B) IDF IPF = = 0.867; 0.552 (C) IDF IPF = = 0.5; 0.478 (D) IDF IPF = = 0.5; 0.318 

asked May 18, 2018 in Power electronics converters by Shimroz123
0 answers 24 views

A single phase 230 V/ 150 V , 1 kVA, 50 Hz transformer is supplied by 230 V AC supply. Find the full load primary and secondary current. 

asked Sep 1, 2018 by Quiz
1 answer 23 views

A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current, if the triggering angle is 30o, the input power factor will be  (A) 0.65 (B) 0.78 (C) 0.85 (D) 0.866

asked May 18, 2018 in Power Electronics by Shimroz123
1 answer 18 views

A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the losses, the power factor of the ac mains at half the rated speed is  (A) 0.354 (B) 0.372 (C) 0.90 (D) 0.955

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 41 views

A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is (A) 216 V (B) 226 V (C) 234 V (D) 236 V

asked Apr 28, 2018 in Electrical Engineering by Shimroz123
1 answer 44 views

Explain three phase bridge inverter.

asked Feb 19, 2018 in Unit 4 by Quiz
1 answer 80 views

The locked rotor current in a 3-phase, star connected 15 , kW 4 , pole 230 V , 50 Hz induction motor at rated conditions is 50 A. Neglecting losses and magnetizing current, the approximate locked rotor line current drawn when the motor is connected to a 236 , V 57 Hz supply is  (A) 58.5 A (B) 45.0 A (C) 42.7 A (D) 55.6 A

asked May 17, 2018 in Electrical Machine by Shimroz123
1 answer 17 views

A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode.  (A) because the converter inherently does not provide for free-wheeling (B) because the converter does not provide for free-wheeling for high ... the AC supply (D) or else if a gate pulse to one of the SCRs is missed, it will subsequently cause a high load current in the other SCR.

asked May 18, 2018 in Power electronics converters by Shimroz123
0 answers 13 views

 A single phase full -wave half controlled bridge converter feeds an inductive load: The two SCRs in the converter are connected to a common DC bus. The converter has to have a free wheeling diode (A) Because the converter inherently does not provide for free wheeling (B) Because the converter does not provide for free wheeling for high ... the AC supply (D) Or else if a gate pulse to one of the SCRs is missed, it will subsequently cause a high load current in the other SCR

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 7 views

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 14 views

A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the dc current at 20 A. If the solar cell resistance is 0.5 Ohm ,then each thyristor will be reverse biased for a period of  (A) 125o (B) 120o (C) 60o (D) 55o

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 15 views

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is  (A) 0.78 (B) 0.827 (C) 0.866 (D) 0.9

asked May 18, 2018 in Power electronics converters by Shimroz123
0 answers 21 views

A single phase fully controlled thyristor bridge ac -dc converter is operating at a firing angle of 25 degree and an overlap angle 10 degree with constant dc output current of 20A. The fundamental power factor (displacement factor) at input ac mains is : (A) 0.78 (B) 0.827 (C) 0.866 (0) 0.9

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

A 400 V, 15 kW, 4-pole, 50 Hz, Y-connected induction motor has full load slip of 4%. The output torque of the machine at full load is  (A) 1.66 Nm (B) 95.50 Nm (C) 99.47 Nm (D) 624.73 Nm

asked May 17, 2018 in Induction Machine by Shimroz123
1 answer 153 views

For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is

asked Apr 27, 2018 in Switchgear And Protection by Shimroz123
1 answer 66 views

A single-phase voltage source square -wave inverter feeds pure inductive load. The waveform of the load current will be

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 16 views

A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component of input current will respectively be  (A) 31% and 6.8 A (B) 31% and 7.8 A (C) 66% and 6.8 A (D) 66% and 7.8 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 21 views

a single phase full wave midpoint thyristor converter uses a 230/200V transformer with centre tap on the secondary side. The P.I.V per thyristor is   (A) 100V (B)141.4V (C)200V (D)282.8V

asked May 17, 2018 in Power electronics converters by Shimroz123
1 answer 20 views

A three-phase, fully controlled thyristor bridge converter is used as line commutated inverter to feed 50 kW power 420 V dc to a three-phase, 415 V(line), 50 Hz ac mains. Consider dc link current to be constant. The rms current of the thyristor is  (A) 119.05 A (B) 79.37 A (C) 68.73 A (D) 39.68 A

asked May 18, 2018 in Power electronics converters by Shimroz123
0 answers 14 views

A single phase motor draws a current of 5 A from a 120 V, 60 Hz line. The power factor of the motor is 65%. Calculate the active power absorbed by the motor.  (A) 600 W (B) 390 W (C) 456 W (D) 650 W 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

The low voltage winding of a 400/230 V, 1-phase, 50 Hz transformer is to be connected to a 25 Hz, the supply voltage should be

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 15 views

The meter constant of a single-phase 230 V induction watt hour meter is 400 revolutions per kWh. The speed of the meter disc for a current of 10 A of 0.9 pf lagging will be

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

An additional condition for parallel operation of three-phase transformers over single-phase transformers is that

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 104 views

What is the difference between a thyristor and an SCR?

asked Dec 9, 2017 in Power Electronics by Quiz
1 answer 50 views

The percent resolution of an 8 -bit D/A converter is

asked May 3, 2018 in Power Electronics by Shimroz123
1 answer 29 views

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W

asked Apr 25, 2018 in Instrumentation and control by Shimroz123
0 answers 22 views

A three phase diode bridge rectifier is fed from a 400 V rms, 50 Hz, three phase a.c. source. For the purely resistive load, the peak instantaneous output voltage is 

asked May 25, 2018 in Diode by Shimroz123
1 answer 118 views

Why the power factor of semiconverter is better than full converter?

asked Mar 8, 2018 in Unit 6 by Quiz
0 answers 94 views

The SCR would be turned OFF by voltage reversal of applied anode-cathode ac supply frequency of A) 10 kHz B) 10 Hz C) 5 kHz D) 5 Hz 

asked Jun 18, 2018 in Power Electronics by Shimroz123
1 answer 21 views

SCR is more utilized as compared to Triac because it is

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 21 views

An SCR without any external connections is considered as (A) two diodes in series (B) three diodes in series (C) two n-p-n transistors in series (D) two p-n-p transistors in series

asked Apr 28, 2018 in Power Electronics by Shimroz123
1 answer 16 views
1 answer 40 views

What is the use of SCR?

asked Dec 9, 2017 in Power Electronics by Quiz
1 answer 32 views

A 400 V, 50 Hz three-phase induction motor rotates at 1440 rpm on full -load. The motor is wound for

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 38 views

The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque  (1) Decreases (2) Increases (3) Remains constant (4) None of the above

asked May 1, 2018 in Electrical Machine by Shimroz123
1 answer 6 views

In a single-phase full converter, the number of SCRs conducting during overlap is   (a) 1 (b) 2 (c) 3 (d) 4 

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 33 views

A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be

asked May 8, 2018 in Electrical Machine by Shimroz123
1 answer 24 views

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
0 answers 24 views

A 750 Hp, 250 V, 1200 r/min DC motor is connected to a 208 V, 3 phase, 60 Hz, line using a 3 phase bridge converter. The full load armature current is 2500 A and the armature resistance is 4 m ohm. Calculate the required firing angle under rated full load conditions.  (A) 45 deg (B) 208 deg (C) 27 deg (D) 32 deg 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...