21 views
in Electrical Engineering by
A network that consists of at least a voltage source or current source is called

A) Active network B) Ideal network

C) Sourced network D) Outsourced network

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

1 Answer

0 votes
by

A network that consists of at least a voltage source or current source is called Active network

Related questions

1 answer 24 views

A network is said to be under resonance when the voltage and the current at the network input terminals are (A) in phase (B) out of phase (C) in phase quadrature (D) in phase, and have equal magnitudes

asked Apr 28, 2018 in Network Analysis by Shimroz123
1 answer 30 views

Which of the following theorems enables a number of voltage (or current) source to be combined directly into a single voltage (or current) source. (1) compensation theorem (2) reciprocity theorem (3) superposition theorem (4) Millman's theorem

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 26 views

A current controlled voltage source is equivalent to :  (A) series voltage feed -back amplifier (B) shunt current feed -back amplifier (C) shunt voltage feed -back amplifier (D) series current feed -back amplifier

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

The internal resistances of an ideal current source, and an ideal voltage source are, respectively, (A) 0, ∞ (B) ∞, ∞ (C) ∞, 0 (D) 0,0

asked Apr 28, 2018 in Network Analysis by Shimroz123
1 answer 19 views

Which of the following is the least expensive protection for over current in low voltage system?  (A) Rewireable fuse (B) Isolator (C) Oil Circuit breaker (D) Air break circuit breaker

asked May 8, 2018 in Electrical Engineering by Zeeshan
1 answer 69 views

A single-phase voltage source square -wave inverter feeds pure inductive load. The waveform of the load current will be

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 271 views

Justify. Power MOSFET is operated at high enough gate source voltage to minimize the conduction losses. 

asked Dec 7, 2017 in Unit 1 by Quiz
1 answer 28 views

A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 73 views

 An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 79 views

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 32 views

Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

what is ideal voltage source?

asked Aug 14, 2017 in Electrical Engineering by Zeeshan
2 answers 32 views

A network which contains one or more than one source of e.m.f. is known as?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 22 views

A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______ A) DC voltage restorer B) Clamping circuit C) Both A and B D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 94 views

A voltage source inverter is normally employed when  (1) source inductance is large and load inductance is small (2) source inductance is small and load inductance is large (3) both source and load inductance are small (4) both source and load inductance are large

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 31 views

A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 10 views

A network consists of several inductances connected in parallel. The equivalent inductance of the network is given by (A) the sum of the individual inductances. (B) the reciprocal of the sum of the individual inductances. (C) the sum of the reciprocals of individual inductances. (D) the reciprocal of the sum of reciprocals of individual inductances.

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 60 views

Give the circuit analysis of current source inverter with resistive load. What are the main difference between voltage source inverter and current source inverter?

asked Feb 18, 2018 in Unit 4 by Quiz
1 answer 71 views

A voltage source inverter will have better performance if its  (1) load inductance is small and source inductance is large.  (2) both load and source inductance are small.  (3) both load and source inductances are large.  (4) load inductance is large and source inductance is small. 

asked Apr 30, 2018 in Power Electronics by Shimroz123
1 answer 17 views

For a voltage source?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 36 views

In voltage source converter based HVDC transmission system the active power is controlled by changing (A) phase angle of the converter ac input voltage (B) supply frequency of the converter ac input voltage (C) magnitude of the converter ac input voltage (D) DC voltage at the inverter terminals

asked Apr 28, 2018 in High voltage engineering by Shimroz123
1 answer 68 views

What is Voltage Source Inverter (VSI) ?

asked Aug 9, 2017 in Unit 2 by Zeeshan
1 answer 15 views

An ideal voltage source has?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 14 views

An ideal voltage source should have?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 20 views

Electrical shock happens for voltage/current?

asked Oct 30, 2017 in Electrical Engineering by Niloy
1 answer 27 views

A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

asked Jun 18, 2018 in Diode by Shimroz123
1 answer 36 views

Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 106 views

Why does increase in current mean a decrease in voltage?

asked Mar 10, 2018 in High voltage engineering by Quiz
1 answer 67 views

Define: 1) voltage ratio, 2) current ratio, 3) transformation ratio of transformer.

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 25 views

A sine wave voltage is applied across an inductor. When the frequency of the voltage is decreased, the current decreases.

asked Nov 23, 2017 in Electrical Engineering by James
1 answer 56 views

Why inductor current lags inductor voltage ?

asked May 24 by Shimroz123
1 answer 7 views

Explain lagging quantity and leading quantity, explain this concept with voltage and current waveform

asked Sep 7, 2018 by Shimroz123
2 answers 50 views

Write the relation between phase and line current, phase and line voltage for Star connection.

asked Aug 11, 2018 in Basic electrical and electronics engineering by Quiz
2 answers 51 views

When a voltage of one volt is applied, a circuit allows one micro ampere current to flow through it. The conductance of the circuit is?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 76 views

Norton’s theorem states that a complex network connected to a load can be replaced with an equivalent impedance (A) in series with a current source (B) in parallel with a voltage source (C) in series with a voltage source (D) in parallel with a current source

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 16 views

Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 52 views

 The number of loop equations required to completely analysing a network comprising of 8 independent branches and 6 nodes including the reference node shall be A) 3 B) 2 C) 4 D) 5 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

A Two-Port Network is said to be symmetrical when the following equalities hold good (A) Z11 = Z22 and Z12 = Z21 (B) Z11 = Z22 (C) Y12 = Y21 (D) Y11 = Y22 and Y12 = Y21

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
2 answers 38 views

The inrush current of a transformer at no load is maximum if the supply voltage is switched on  (1) at peak voltage value (2) at zero voltage value (3) at half voltage value (4) at 0.866 time voltage value

asked Apr 30, 2018 in Switchgear And Protection by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

The number of independent loops for a network with n nodes and b branches is

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 22 views

A closed path made by several branches of the network is known as?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 10 views

A passive network

asked Apr 26, 2018 in Electrical Engineering by Shimroz123
2 answers 40 views

Is current from a battery AC or DC?

asked Mar 14, 2018 in Electrical Engineering by Quiz
1 answer 24 views

In a battery, the difference between the no-load voltage and the measured voltage output is called ________ A) Internal voltage B) Internal resistance C) External resistance D) All the above

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of______degrees.

asked Mar 24, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

Which of the following are known as the short circuit parameters of a 2- port network? (A) Z- parameters. (B) H- parameters. (C) Y- parameters. (D) A,B,C,D, parameters.

asked Apr 28, 2018 in Network Analysis by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

133 comments

3,086 users

...