28 views
in Network Analysis by
A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will

1 Answer

0 votes
by

A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will not change

Related questions

0 answers 14 views

A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled, then voltage across each resistor is  A) Halved B) Doubled C) Increases by 4 times D) Remains the same

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

As a network contains only independent current sources and resistors then if the values of all resistors are doubled then the values of the node voltages are   (A) will become half (B) will remain unchanged (C) will become double (D) cannot be determined unless the circuit configuration and the values of the resistors are known.

asked May 17, 2018 in Network Analysis by Shimroz123
1 answer 17 views

The internal resistances of an ideal current source, and an ideal voltage source are, respectively, (A) 0, ∞ (B) ∞, ∞ (C) ∞, 0 (D) 0,0

asked Apr 28, 2018 in Network Analysis by Shimroz123
1 answer 24 views

A network is said to be under resonance when the voltage and the current at the network input terminals are (A) in phase (B) out of phase (C) in phase quadrature (D) in phase, and have equal magnitudes

asked Apr 28, 2018 in Network Analysis by Shimroz123
1 answer 24 views

The power flow problem mathematical model for a linear transmission network (A) is non-linear (B) is linear (C) considers time variation of generation (D) does not consider tap-changing transformers

asked Apr 28, 2018 in Power system by Shimroz123
1 answer 15 views

An ideal voltage source has?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 14 views

An ideal voltage source should have?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 17 views

Voltage dependent resistors are used?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 12 views

Voltage dependent resistors are usually made from?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 32 views

Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

A network that consists of at least a voltage source or current source is called A) Active network B) Ideal network C) Sourced network D) Outsourced network

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

what is ideal voltage source?

asked Aug 14, 2017 in Electrical Engineering by Zeeshan
2 answers 29 views

A network which contains one or more than one source of e.m.f. is known as?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 9 views

A passive network is one which contains?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 19 views

A non-linear network does not satisfy?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 22 views

Three identical resistors are first connected in parallel and then in series. The resultant resistance of the first combination to the second will be?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 15 views

Which of the following are known as the short circuit parameters of a 2- port network? (A) Z- parameters. (B) H- parameters. (C) Y- parameters. (D) A,B,C,D, parameters.

asked Apr 28, 2018 in Network Analysis by Shimroz123
1 answer 18 views

When three resistors with unequal values are connected in parallel, _______ A) The current across the resistors is the same  B) The voltage drop across the resistors is the same C) The voltage drops across the resistors is proportional to the resistance of each resistor D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

The number of independent loops for a network with n nodes and b branches is

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 15 views

The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 22 views

What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 45 views

What are the different sources of renewable energy?

asked Dec 18, 2017 in Renewable energy sources by Quiz
1 answer 19 views

A system is linear if and only if it satisfies

asked May 3, 2018 in Control System by Shimroz123
1 answer 14 views

Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

A closed path made by several branches of the network is known as?

asked Mar 25, 2018 in Network Analysis by Shimroz123
2 answers 159 views

What is the difference between renewable and nonrenewable energy sources?

asked Dec 18, 2017 in Renewable energy sources by Quiz
1 answer 9 views

What is active and passive network?

asked Jul 4 in Network Analysis by Shimroz123
1 answer 202 views

What are the desirable characteristics of ideal switch?

asked Feb 5, 2018 in Unit 1 by Quiz
1 answer 36 views

What are the disadvantages of the linear regulator? how are they overcome in the switching regulator? What is continuous and discontinuous mode switching regulator?

asked Feb 11, 2018 in Unit 2 by Quiz
1 answer 22 views

According to Kirchhoffs voltage law, the algebraic sum of all IR drops and e.m.f. in any closed loop of a network is always?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 28 views

Consider a circuit with four 10 Ω resistors connected in parallel and the current flowing through the circuit is 5 A. What will be the current if the above 4 resistors are connected in parallel? A) 5 A B) 50 A C) 500 A D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 2 views

List any four sources of energy. 

asked Sep 8, 2018 by Shimroz123
2 answers 52 views

If resistance is 8 Ohm and current is 16 ampere then what will be the voltage and power?

asked Oct 21, 2017 in Electrical Engineering by Quiz
0 answers 17 views

What do you mean by network theory?

asked Mar 10, 2018 in Network Analysis by Quiz
0 answers 959 views

What is the difference between linear and nonlinear electrical loads?

asked Mar 10, 2018 in Power quality by Quiz
1 answer 28 views

Which of the following converts linear displacement from a mechanical reference into a proportional electrical signal containing phase and amplitude information? A) CRO B) LVDT C) RVDT D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 39 views

Compare conventional energy sources with renewable energy sources on any four points. 

asked Sep 7, 2018 by Shimroz123
1 answer 14 views

Two resistors are said to be connected in series when?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 21 views

Wire-wound resistors are unsuitable for use at high frequencies because they?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

Linear and non-linear device

asked May 16 by Shimroz123
1 answer 24 views

The gain of an ideal amplifier must be

asked Apr 26, 2018 in Control System by Shimroz123
1 answer 27 views

What should be the ideal resistance of ammeter ?

asked Mar 8, 2018 in Electronics Engineering by Quiz
0 answers 22 views

If both the number of turns and core length of an inductive coil are doubled, then its self inductance will be (a) halved (b) doubled (c) quadrupled (d) unaffected

asked May 25, 2018 in Inductance by Shimroz123
1 answer 13 views

If the secondary turns of a transformer are doubled and at the same time primary voltage is reduced to half then the secondary voltage will

asked May 15, 2018 in Transformer by Shimroz123
1 answer 50 views

 The number of loop equations required to completely analysing a network comprising of 8 independent branches and 6 nodes including the reference node shall be A) 3 B) 2 C) 4 D) 5 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

A network consists of several inductances connected in parallel. The equivalent inductance of the network is given by (A) the sum of the individual inductances. (B) the reciprocal of the sum of the individual inductances. (C) the sum of the reciprocals of individual inductances. (D) the reciprocal of the sum of reciprocals of individual inductances.

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 11 views

Is a convolution linear?

asked Mar 11, 2018 in Signals and Systems by Shimroz
0 answers 20 views

What is a non linear load?

asked Mar 10, 2018 in Power quality by Quiz

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...