29 views
in Power system by
If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then 

(A) zero sequence currents are present on both sides of the transformer 

(B) zero sequence currents are absent on both sides of the transformer 

(C) zero sequence currents are present on the secondary side but not on the primary side 

(D) zero sequence currents are present on the primary side but not on the secondary side

1 Answer

0 votes
by

If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then zero sequence currents are absent on both sides of the transformer 

Related questions

3 answers 269 views
1 answer 79 views
1 answer 16 views

The line current in a balanced delta system is 30 A. The load current is (A) 30√3 A (B) 30/√3 A (C) 10 A (D) 30/√2 A

asked Apr 28, 2018 in Network Analysis by Shimroz123
2 answers 50 views

Write the relation between phase and line current, phase and line voltage for Star connection.

asked Aug 11, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 84 views

To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ?

asked Apr 27, 2018 in Switchgear And Protection by Shimroz123
1 answer 22 views

In the case of an unsymmetrical alternating current the average value must always be taken over?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 38 views

Increasing the number of turns of wire on the secondary of a transformer will  (A) Decrease the secondary current (B) Increase the primary current (C) Have no effect on the secondary current (D) Increase the secondary current

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

The secondary of a current transformer is always short-circuited under operating conditions because it?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 31 views

When secondary of a current transformer is open-circuited its iron core will be?

asked Mar 19, 2018 in Transformer by Shimroz123
1 answer 25 views

A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

In a transformer the resistance between its primary and secondary should be?

asked Mar 19, 2018 in Transformer by Shimroz123
0 answers 50 views

What is line voltage and phase voltage? Draw balanced three phase star connected system. Show all the voltages and currents.

asked Aug 11, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 14 views

If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be

asked Apr 29, 2018 in Power system by Shimroz123
0 answers 27 views

A star circuit has element of resistance R/2. The equivalent delta elements will be?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 24 views

A network is said to be under resonance when the voltage and the current at the network input terminals are (A) in phase (B) out of phase (C) in phase quadrature (D) in phase, and have equal magnitudes

asked Apr 28, 2018 in Network Analysis by Shimroz123
1 answer 21 views

In which fault the maximum short circuit current occurs?

asked Mar 19, 2018 in Switchgear And Protection by Shimroz123
1 answer 30 views

The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be?

asked Mar 20, 2018 in Induction Machine by Shimroz123
1 answer 34 views

The severity of line to ground and three phase faults at the terminals of an unloaded synchronous generator is to be same. If the terminal voltage is 1.0 pu, Z1=Z2=j0.1 p.u. and Z0= j0.05 p.u. for the alternator, then the required inductive reactance for neutral grounding is   (a) 0.05 p.u. (b) 0.0166 p.u. (c) 0.1 p.u. (d) 0.15 p.u.

asked May 13, 2018 in Electrical Engineering by Shimroz123
0 answers 26 views

When a line -to -ground fault occurs, the current in a faulted phase is 100A. The negative sequence current in this case will be : (A) Zero (B) 33.3 A (C) 66.6 A (D) 100 A

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 40 views

A 4000 kVA, 11 kV/132 kV delta-star connected 3-phase transformer has reactance, x1 = 0.12 p.u. The actual value of x1 referred to the low voltage side is (A) 0.85 Ω (B) 3.63 Ω (C) 36.3 Ω (D) 252 Ω

asked Apr 28, 2018 in Power system by Shimroz123
0 answers 38 views

A balanced Delta connected load supplied with 440 V 50 Hz three phase AC supply has R=10 Ohm and L=0.6 mH in is each arm. Calculate line and phase current, active power.

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 22 views

A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :  (A) less than 66 kV (B) lie between 66 kV and 110 kV (C) more than 165 kV (D) lie between 110 kV and 165 kV

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be

asked May 8, 2018 in Switchgear And Protection by Shimroz123
1 answer 21 views

A shunt fault is characterized by (A) Increase in current, frequency and pf (B) Increase in current, reduction in frequency and pf (C) Increase in current and frequency, reduction in pf (D) Decrease in current and frequency

asked Apr 28, 2018 in Power system by Shimroz123
0 answers 20 views

The zero sequence current of a generator for line to ground fault is j 2.4 p.u. The current through the neutral during the fault is (a) j 0.8 p.u (b) j 2.4 p.u. (c) j 0.24 p.u. (d) j 7.2 p.u. 

asked May 25, 2018 in Power system by Shimroz123
1 answer 79 views

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 27 views

On the ladder resting on the ground and leaning against a smooth vertical wall, the force of friction will be?

asked Mar 22, 2018 in Engineering Mechanics by Shimroz123
1 answer 28 views

On a ladder resting on smooth ground and leaning against vertical wall, the force of friction will be?

asked Mar 22, 2018 in Engineering Mechanics by Shimroz123
1 answer 40 views

If the % reactance upto the fault point is 20%, then the short circuit current will be

asked May 8, 2018 in Switchgear And Protection by Shimroz123
1 answer 134 views

Shunt compensation in an EHV line is used to (A) Improve stability. (B) Improve the voltage profile. (C) Reduce the fault level. (D) Substitute for synchronous phase modifier.

asked May 8, 2018 in Power system by Shimroz123
1 answer 19 views

A transmission line of 200 km has a certain A, B, C and D parameters. If the length is reduced to 60 km

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
2 answers 38 views
1 answer 28 views

What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased? A) It increases B) It decreases C) It remains the same D) Cannot say unless the actual percentage increase in the frequency is known

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 36 views

With fault clearing time, the transient stability of a power system

asked Apr 27, 2018 in Switchgear And Protection by Shimroz123
1 answer 21 views

The number of terminals present in IGBT is A) 2 B) 3 C) 4 D) 5

asked Jun 18, 2018 in IGBT by Shimroz123
3 answers 45 views

A MOSFET has how many terminals?

asked Mar 19, 2018 in MOSFET by Shimroz123
2 answers 95 views

The sending end and receiving end voltages of a three-phase transmission line are 10 kV/ph and 9.5 kV/ph, respectively. If the resistance drop is 150 V/ph and receiving end power factor is 0.8, the sending end power factor is (A) 0.745 lagging (B) 0.775 lagging (C) 0.8 lagging (D) 0.85 lagging

asked Apr 28, 2018 in Power system by Shimroz123
2 answers 18 views

Why CT is never operated with an open secondary ?

asked Sep 6, 2018 by Shimroz123
1 answer 21 views

Which is the most common type of fault?

asked Mar 19, 2018 in Switchgear And Protection by Shimroz123
1 answer 115 views

In a transmission line if booster transformers are to be used, preferred location will be  (A) At the receiving end (B) At the sending end (C) At the intermediate point (D) Anywhere in the line 

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 13 views

The ALE line of an 8085 microprocessor is used to (A) latch the output of an I/O instruction into an external latch. (B) deactivate the chip-select signal from memory devices. (C) find the interrupt enable states of the TRAP interrupt. (D) latch the 8 bits of address lines AD7-AD0 into an external latch.

asked Apr 28, 2018 in Digital Electronics by Shimroz123
0 answers 15 views
0 answers 28 views

Draw the Delta connected three phase system showing all the voltages and currents. Write the power equation.

asked Aug 11, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 27 views

Series capacitive compensation in EHV transmission line is used to

asked Apr 29, 2018 in Power system by Shimroz123
1 answer 4 views

State the meaning of secondary instrument. Classify secondary instruments.

asked Sep 6, 2018 by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...