# Generally in a power system network, the load is represented as a :

26 views
Generally in a power system network, the load is represented as a :

(A) Constant power in both load flow study and in stability study

(B) Constant power in load flow study and constant impedance in stability study

(C) Constant power in stability study and constant impedance in load flow study

(D) Constant impedance in both load flow study and in stability study

Generally in a power system network, the load is represented as a : Constant power in load flow study and constant impedance in stability study

## Related questions

The power flow problem mathematical model for a linear transmission network (A) is non-linear (B) is linear (C) considers time variation of generation (D) does not consider tap-changing transformers

The sequence components of current of a single-phase load connected to a 3-phase system are (A) equal positive and negative sequence components (B) equal positive, negative and zero sequence components (C) vector sum of sequence currents is zero (D) algebraic sum of sequence currents is zero

The benefit of power factor correction in a power system is (A) lower power consumption (B) increased demand charge (C) reduced load carrying capabilities in existing lines (D) reduced voltage profile

Load compensation in power systems is a process to :  (A) Maintain better voltage profile (B) Increase short circuit capacity of the system (C) Generate required harmonics for loads like arc furnaces (D) Compensate for the line reactance

A transformer has negative voltage regulation when its load power factor is   (1) Zero (2) Unity (3) Leading (4) Lagging

The stability of the power system is not affected by  (1) generator reactance (2) line reactance (3) line losses (4) output torque

State why nuclear power plants are used as base load plants and diesel power plants as a peak load plant.

If non-linear loads are connected to the power system, then (A) displacement power factor is same as the total power factor (B) displacement power factor is not equal to the total power factor (C) displacement power factor is due to harmonic currents (D) total power factor is due to fundamental component of current

Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW then annual energy production is  (1) 122.8 GWh (2) 198.55 GWh (3) 128.2 GWh (4) 188.82 GWh

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

The power consumed by a balanced 3-ph load is measured by two-wattmeter method. The meter readings are 8 kW and 4 kW. The power factor of the load is (A) zero (B) 0.5 (C) between zero and 0.5 (D) between 0.5 and unity

The maximum load that a power transformer can carry is limited by its?

A lightening arrester connected between the line and earth in a power system  (1) protects the terminal equipment against travelling surges (2) protects the transmission line against direct lightening strokes (3) suppresses high frequency oscillations in the line (4) reflects back the travelling wave approaching it

In a synchronous generator delivering lagging power factor load  (1) the excitation emf leads terminal voltage by the power angle (2) the excitation emf lags terminal voltage by the power angle (3) excitation emf leads the terminal voltage by the power factor angle (4) excitation emf lags the terminal voltage by the power factor angle

What is the choice of size and number of generator units in interconnected power system?

In voltage source converter based HVDC transmission system the active power is controlled by changing (A) phase angle of the converter ac input voltage (B) supply frequency of the converter ac input voltage (C) magnitude of the converter ac input voltage (D) DC voltage at the inverter terminals

For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is

Minimum voltage regulation occurs when the power factor of the load is?

If the load of the normally excited synchronous motor is increased the power factor will?

The synchronous motor which works on leading power factor and does not drive any mechanical load is called?

The synchronous motor will develop maximum power when the load angle is?

What is sag in power system?

What is meant by feeder in power system?

What is microgrid in power system?

In tuned power lines, on load :  (A) the receiving end voltage is numerically equal to the sending end voltage  (B) the receiving end current is numerically equal to the sending end current  (C) there is no voltage drop  (D) all the above

steady-state stability of a power system is improved by

State the functions of fuel system and exhaust system of a diesel power station.

With fault clearing time, the transient stability of a power system

What are the components of a power system?

In load flow Study, a PV bus is treated as a PQ bus when

Power factor of the system is kept high?

Explain starting system in diesel electric power plant.

Explain fuel system and air intake system in diesel electric power plant.

A closed path made by several branches of the network is known as?

What is power system planning?

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

A network which contains one or more than one source of e.m.f. is known as?