43 views
in Electrical Engineering by
For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

1 Answer

0 votes
by

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is 0.707 lead

Related questions

1 answer 41 views

what is mean by short transmission line ?

asked Aug 18, 2017 in Electrical Engineering by Zeeshan
1 answer 95 views

A transmission line has 1 P.0 impedance on a base of 11 KV, 100 MVA. On a base of 55 KV. it will have a P.0 impedance of

asked May 3, 2018 in Electric Power Transmission by Shimroz123
1 answer 123 views

A 50Ω transmission line is terminated in an impedance of 20-j50. What will be the reflection coefficient? A) 0.69 B) 1.69 C) 6.9 D) 16.9 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 115 views

In a transmission line if booster transformers are to be used, preferred location will be  (A) At the receiving end (B) At the sending end (C) At the intermediate point (D) Anywhere in the line 

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 24 views

Transmission efficiency of a transmission line increases with the

asked Apr 26, 2018 in Switchgear And Protection by Shimroz123
1 answer 27 views

The sag of a transmission line is least affected by (A) Self weight of the conductor. (B) Temperature of the surrounding air. (C) Current through the conductor. (D) Ice deposited on the conductor.

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

A transmission line of 200 km has a certain A, B, C and D parameters. If the length is reduced to 60 km

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

Stability of a transmission line can be increased by

asked May 8, 2018 in Electric Power Transmission by Shimroz123
2 answers 95 views

The sending end and receiving end voltages of a three-phase transmission line are 10 kV/ph and 9.5 kV/ph, respectively. If the resistance drop is 150 V/ph and receiving end power factor is 0.8, the sending end power factor is (A) 0.745 lagging (B) 0.775 lagging (C) 0.8 lagging (D) 0.85 lagging

asked Apr 28, 2018 in Power system by Shimroz123
1 answer 43 views

what is mean by medium transmission line ?

asked Aug 18, 2017 in Electrical Engineering by Zeeshan
1 answer 41 views

what is mean by long transmission line ?

asked Aug 18, 2017 in Electrical Engineering by Zeeshan
0 answers 14 views

What are the losses in a transmission line?

asked Mar 10, 2018 in High voltage engineering by Quiz
1 answer 27 views

Series capacitive compensation in EHV transmission line is used to

asked Apr 29, 2018 in Power system by Shimroz123
1 answer 51 views

If 3000 kW power is to be transmitted over a distance of 30 km, the desirable transmission voltage will be.  (A) 11 kV (B) 33 kV (C) 66 kV (D) 132 kV

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 36 views

For a 500 Hz frequency excitation, a 50 km long power line will be modeled as

asked Apr 29, 2018 in Power system by Shimroz123
1 answer 12 views

The standing wave ratio of a 75 Ω transmission line used to feed a 300 Ω resistive load will be _____.

asked May 29, 2018 in Electrical Engineering by Shimroz123
1 answer 42 views

If the % reactance upto the fault point is 20%, then the short circuit current will be

asked May 8, 2018 in Switchgear And Protection by Shimroz123
0 answers 19 views

A three phase transmission line delivers a load of 5 MW at 0.8 power factor lagging. Resistance of each conductor is 0.5 ohm / km. Receiving end voltage is 33 kV. If the line loss is not to exceed 10%, determine the length of the line.  (A) 7 km (B) 27.9 km (C) 56.8 km (D) 13.9 km

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 24 views

For 11kV line the inductance per km per phase will be of the order of:  (A) 1 H (B) 0.1 H (C) 1 mH (D) 0.1 mH

asked May 8, 2018 in Electric Power Transmission by Shimroz123
2 answers 38 views

Pure inductive circuit takes power from the A.C. line when?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 3 views

Define load and line regulation.

asked Sep 5, 2018 by Shimroz123
0 answers 38 views

A balanced Delta connected load supplied with 440 V 50 Hz three phase AC supply has R=10 Ohm and L=0.6 mH in is each arm. Calculate line and phase current, active power.

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 20 views

In a transformer the voltage regulation will be zero when it operates at (A) unity p.f. (B) leading p.f. (C) lagging p.f. D) zero p.f. leading.

asked May 22, 2018 in Transformer by Shimroz123
1 answer 24 views

The unit circle of the Nyquist plot transforms into unity or 0 dB line of the amplitude plot of the Bode diagram for

asked Apr 26, 2018 in Control System by Shimroz123
0 answers 16 views

For a resonant circuit with resonant frequency of 1 MHz a, 0 = 50 and R = 400, find the value of C (A) 250 pF (B) 1000 pF (C) 1.25 pF (D) 500 pF

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 24 views

The power flow problem mathematical model for a linear transmission network (A) is non-linear (B) is linear (C) considers time variation of generation (D) does not consider tap-changing transformers

asked Apr 28, 2018 in Power system by Shimroz123
1 answer 21 views

Minimum voltage regulation occurs when the power factor of the load is?

asked Mar 19, 2018 in Transformer by Shimroz123
0 answers 45 views

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 5 views

What will be the efficiency when the transformer operates at unity power factor and 60% of full load 

asked Sep 1, 2018 by Shimroz123
1 answer 27 views

A transformer has negative voltage regulation when its load power factor is   (1) Zero (2) Unity (3) Leading (4) Lagging

asked Apr 30, 2018 in Power system by Shimroz123
0 answers 18 views

If the transmission line is loaded with leading reactive volt amperes, there will be rise of voltage at the receiving end and this (a) increases (b) decreases (c) remains same with the increase in the length of line (d) none of these

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 40 views

When 7/0.029 V.I.R cable is carrying 20 A, a drop of 1 V occurs every 12 m. The voltage drop in a 100 m run of this cable when it is carrying 10 A is nearly  (a) 4.2 V (b) 3.2 V (c) 1.2 V (d) 0.42 V

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 73 views

The X:R ratio of 220 kV line as compared to 400 kV line is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 106 views

If a 5-bus test system contains 6 transmission lines and one transformer, how many non-zero elements are there in the system Y-bus ? (A) 25 (B) 12 (C) 11 (D) 19

asked Apr 28, 2018 in Power system by Shimroz123
1 answer 55 views

How many insulator disc used for 33 kV transmission voltage line?

asked Dec 5, 2017 in Electric Power Transmission by Quiz
1 answer 28 views

The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole)  (A) has q -axis current only (B) has d -axis current only (C) has both d and q axis currents (D) cannot be divided between q and d axis currents

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 15 views

Which of the following are known as the short circuit parameters of a 2- port network? (A) Z- parameters. (B) H- parameters. (C) Y- parameters. (D) A,B,C,D, parameters.

asked Apr 28, 2018 in Network Analysis by Shimroz123
1 answer 16 views

The line current in a balanced delta system is 30 A. The load current is (A) 30√3 A (B) 30/√3 A (C) 10 A (D) 30/√2 A

asked Apr 28, 2018 in Network Analysis by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,471 questions

7,069 answers

134 comments

3,088 users

...