Can you help by answering this question?

Write any six important requirements of a traction motor

23 views
in Electrical Engineering by
We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

1 Answer

0 votes
by

We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be 2.4 kOhm

Related questions

1 answer 17 views

A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be:

asked May 22, 2018 in Electrical Engineering by Shimroz123
1 answer 48 views

Two 100W, 200V lamps are connected in series across a 200V supply. The total power consumed by each lamp will be in Watts

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 80 views

Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 29 views

The effective resistance of an iron-cored choke working on ordinary supply frequency is more than its true resistance because of?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

What will happen if the primary of a transformer is connected to D.C. supply?  (A) Transformer will operate with low efficiency (B) Transformer will operate with high efficiency (C) No effect (D) Transformer may start to smoke and burn 

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 31 views

A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 15 views

In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is :

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 2 views

State the use of shunt and series resistance used in extension of meter.

asked Sep 6, 2018 by Shimroz123
0 answers 22 views

Why a dc series motor has a high starting torque?

asked Mar 15, 2018 in Electrical Engineering by Quiz
0 answers 50 views

What are the advantages of DC series motor?

asked Mar 15, 2018 in Electrical Engineering by Quiz
0 answers 536 views

Why dc series motor should not be started at no load?

asked Mar 15, 2018 in Electrical Engineering by Quiz
1 answer 32 views

Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

An inductor is connected in series with SCR to protect it from A) Excessive high voltage B) Excessive high dv/dt C) Excessive high di/dt D) Excessive large forward current 

asked Jun 18, 2018 in Inductor by Shimroz123
1 answer 34 views

Two coils connected in series have resistance of 600 ohm and 300 ohm and temperature coefficients of 0.1% and 0.4% respectively.The resistance of the combination at 50oC will be 

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 51 views

Describe the reason of using dc series motor for electric trains.

asked Sep 18, 2018 in Electrical Machine by Shimroz123
1 answer 36 views

A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

asked May 3, 2018 in Electrical Machine by Shimroz123
1 answer 72 views

 An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

A 200 V DC machine supplies 20 A at 200 V as a generator. The armature resistance is 0.2 Ohm. If the machine is now operated as a motor at same terminal voltage and current but with the flux increased by 10%, the ratio of motor speed to generator speed is

asked May 8, 2018 in Electrical Machine by Shimroz123
1 answer 23 views

Why does a transformer only work with an AC supply?

asked Mar 14, 2018 in Electrical Engineering by Quiz
1 answer 20 views

A change of 4% in the supply voltage to an induction motor will produce a change of approximately

asked May 8, 2018 in Electrical Machine by Shimroz123
1 answer 23 views

While keeping the excitation constant, if the steam supply of an alternator running in parallel with another identical alternator is increased, then (A) It would over-run the other alternator (B) Its rotor will fall back in phase with respect to the other machine (C) Its portion of share in load will increase (D) Its power factor would be decreased.

asked Apr 28, 2018 in Electrical Machine by Shimroz123
1 answer 30 views

A 40 W bulb is connected in series with a room heater. If now 40 W bulb is replaced by 100 W bulb, the heater output will?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 14 views
1 answer 34 views

Cells are connected in series in order to?

asked Mar 16, 2018 in Electrical Engineering by Quiz
1 answer 25 views

If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 39 views

The normal value of the armature resistance of a d.c. motor is?

asked Mar 26, 2018 in DC motor by Shimroz123
1 answer 37 views

 An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 25 views

In a three-phase supply floating neutral is undesirable because it way give rise to?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

asked Mar 20, 2018 in Induction Machine by Shimroz123
1 answer 37 views

If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 16 views

Two resistors are said to be connected in series when?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 14 views

In a series R-C circuit, with the increase in frequency, current (A) Reduces (B) Increases (C) Does not change (D) Becomes zero

asked May 8, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,085 users

...