Can you help by answering this question?

Ferranti effect on long overhead lines is experienced when

17 views
in Bipolar Junction Transistor by
In BJT, the common emitter gain β is

(A) desired to have large value (B) desired to have small value

(C) desired to have moderate value (D) the value need not be controlled

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

2 Answers

0 votes
by

In BJT, the common emitter gain β is desired to have large value

0 votes
by

In BJT, the common emitter gain β is desired to have large value. 

β is the Current gain factor also called transport factor. 

Related questions

1 answer 78 views

 If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be A) 0.98 B) 0.41 C) 59 D) 55  

asked Jun 18, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 20 views

In BJT circuits, bulk of the gain is provided by (A) CE configuration (B) CB configuration (C) CC configuration (D) It is not certain

asked May 12, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 18 views

In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the base current is: (1) 10 µA (2) 100 µA (3) 1 A (4) 10 A 

asked May 29, 2018 in Electronics Engineering by Shimroz123
2 answers 17 views

For the active mode BJT operation (A) Emitter Base Junction is Forward Biased and Collector Base Junction is Forward Biased (B) Emitter Base Junction is Reverse Biased and Collector Base Junction is Reverse Biased (C) Emitter Base Junction is Forward Biased and Collector Base Junction is Reverse Biased (D) Emitter Base Junction is Reverse Biased and Collector Base Junction is Forward Biased

asked May 12, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 14 views

What is an emitter follower BJT circuit ? (A) Common Collector Amplifier (B) Common Emitter Amplifier (C) Common Base Amplifier (D) None of the above

asked May 12, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 14 views

A certain common-emitter amplifier has a voltage gain of 100. If the emitter bypass capacitor is removed.  a. The circuit will become unstable b. The voltage gain will decrease  c. The voltage gain will increase d. The circuit will become stable

asked Aug 31, 2018 by Shimroz123
1 answer 10 views

Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

asked Sep 2, 2018 by Shimroz123
1 answer 15 views

In a BJT circuit a pnp transistor is replaced by npn transistor. To analyse the new circuit (1) All calculations done earlier have to be repeated (2) Replace all calculated voltages by reverse values (3) Replace all calculated currents by reverse values (4) Replace all calculated voltages and currents by reverse values 

asked May 28, 2018 in Bipolar Junction Transistor by Shimroz123
2 answers 20 views

A bipolar junction transistor (BJT) is used as a power control switch by biasing it in the cut-off region (OFF state) or in the saturation region (ON state). In the ON state, for the BJT  (A) both the base-emitter and base-collector junctions are reverse biased (B) the base-emitter junction is reverse ... (C) the base-emitter junction is forward biased, and the base-collector junction is reverse biased (D) both the base-emitter and base-collector junctions are forward biased

asked May 18, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 19 views

The ac bypassing of RF by CF in a common emitter configuration :  (A) increases ac signal across emitter -base junction (B) decreases ac signal across emitter -base junction (C) decreases voltage amplification (D) stabilizes the Q -point

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 46 views

In a differential amplifier the differential voltage gain is 500 and the common mode voltage gain is 0.5. The CMRR in dB is (a) 80 (b) 60 (c) 30 (d) 20

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 71 views

What is the difference between BJT and FET?

asked Mar 19, 2018 in Bipolar Junction Transistor by Zeeshan
1 answer 11 views

Draw output characteristics of common emitter [CE] configuration and explain active, saturation and cut-off regions in detail. 

asked Jul 10 in Elements of Electronics by Shimroz123
0 answers 32 views

What is a BJT amplifier?

asked Mar 19, 2018 in Bipolar Junction Transistor by Zeeshan
1 answer 23 views

The current gain of emitter follower is: A) less than one B) more than one C) zero D) unpredictable

asked Jun 4, 2018 in Power Electronics by Shimroz123
1 answer 111 views

Why common emitter configuration is commonly used?

asked Sep 4, 2018 by Shimroz123
1 answer 60 views

A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 98 views

A differential amplifier has a differential gain of 20,000, CMRR : 80 dB. The common mode gain is given by

asked May 3, 2018 in Power Electronics by Shimroz123
1 answer 52 views

As compared to power MOSFET, a BJT has  (a) Lower switching losses but higher conduction losses (b) Higher switching losses and higher conduction losses (c) Higher switching losses but lower conduction losses (d) Lower switching losses and lower conduction losses. 

asked May 13, 2018 in Bipolar Junction Transistor by Shimroz123
0 answers 24 views

How can BJT be used as an amplifier?

asked Mar 19, 2018 in Bipolar Junction Transistor by Zeeshan
1 answer 23 views

The voltage gain of a common base amplifier depends on  1. Load resistor RL 2. input resistance of transistor 3. Ac alpha 4. All the above 

asked May 13, 2018 in Amplifier by Shimroz123
1 answer 72 views

The voltage gain of a common -source JFET amplifier depends up on its  (1) Input impedance (2) Amplification factor (3) Dynamic drain resistance (4) Drain load resistance

asked Apr 30, 2018 in Power Electronics by Shimroz123
1 answer 128 views

Explain open emitter BJT drive circuit.

asked Feb 19, 2018 in Unit 5 by Quiz
0 answers 9 views

In a synchronous motor, if β is impedance angle and δ is torque angle, then the maximum developed mechanical power is obtained when (a) δ = 180 – 2β (b) δ = 2β (c) δ = 180 – β (d) δ = β  

asked May 25, 2018 in Synchronous machine by Shimroz123
0 answers 39 views

For a symmetrical emitter coupled differential amplifier using transistors of current gain 100, constant current source of 2 mA and with Vcc=10 V, differential input resistance in kOhm is about  A) 2.5 B) 5 C) 10 D) 50

asked Apr 5, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

Identify type of BJT configuration having following features : (i) BJT configuration having the least current gain. (ii) KIT configuration called as voltage follower. (iii) BJT configuration having current gain less than one. (iv) BJT configuration suitable for impedance matching. (v) BIT configuration suitable for voltage amplification. (vi) BJT configuration having the least output impedance.  

asked Jul 10 in Elements of Electronics by Shimroz123
1 answer 18 views

A transistor has a typical value of β = 200 , If the collector current is 15 mA, then base current will be

asked May 14, 2018 in Electronics Engineering by Shimroz123
0 answers 15 views

If the emitter resistance ‘Re ’ in a transistor amplifier is removed, then (a) base to emitter junction will be less forward biased. (b) gain of amplifier decreases. (c) Q-point becomes unstable. (d) All of these 

asked May 25, 2018 in Amplifier by Shimroz123
1 answer 21 views

The most common device used for detection in radio receivers is   (A)amplifier (B) triode (C) diode (D) transistor

asked May 17, 2018 in Electronics communication by Shimroz123
0 answers 47 views

In IC fabrication, the common form of PNP transistor is  A) Vertical PNP B) Lateral PNP C) Triple diffusion PNP D) Substrate PNP

asked Apr 5, 2018 in Electronics Engineering by Shimroz123
1 answer 9 views

Define α & β and derive the relation between (α) &) (β) of transistor.

asked Sep 5, 2018 by Shimroz123
1 answer 22 views

An emitter follower circuit is widely used in electronic instruments because  (A) Its voltage gain is less than unity  (B) its output impedance is high and input impedance is low  (C) its output impedance is low and input impedance is high  (D) none of the above

asked May 12, 2018 in Electronics Engineering by Shimroz123
0 answers 11 views

An emitter resistor is included in CE amplifier to increase  A) Gain B) Bandwidth C) S/N D) Stability

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 30 views

What is the value of Beta in power BJT?

asked Sep 20, 2017 in Electrical Engineering by Quiz
1 answer 45 views

In the emitter characteristic of UJT, the negative resistance portion.  1.lies in the cut-off region 2.continues up to peak point 3.lasts until the valley point is reached 4.does not exist 

asked May 13, 2018 in Power Electronics by Shimroz123
0 answers 46 views

A BJT’s voltage stand-off capability when the base current is zero (A) collector-emitter breakdown voltage (B) minimum collector-emitter voltage (C) collector-base breakdown voltage (D) emitter-base voltage

asked Jun 4, 2018 in Bipolar Junction Transistor by Shimroz123
0 answers 11 views

A single-phase half-controlled rectifier is driving a separately excited dc motor. The dc motor has a back emf constant of 0.5 V/rpm. The armature current is 5 A without any ripple. The armature resistance is 2 Ohm. The converter is working from a 230 V, single-phase ac source with a firing angle of 30o . Under this operating condition, the speed of the motor will be  (A) 339 rpm (B) 359 rpm (C) 366 rpm (D) 386 rpm

asked May 18, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 13 views

The effect of a finite gain of an operational amplifier used in an integrator is that (A) it would not integrate (B) the slope of the output will vary with time (C) the final value of the output voltage will reduce (D) there will be instability in the circuit

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
0 answers 125 views

In a bipolar transistor when in saturation, the dc current gain is (a) less than (3 (b) greater than (3 (c) equal to 13 (d) zero

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

Two transformers with identical voltage ratings are working in parallel to supply common load. The percentage impedance of one transformer is higher compared to that of other. The load sharing between the two transformer will: (1) Be proportional to their percentage impedance (2) Be independent of their percentage impedance (3) Be inversely proportional of their respective impedance (4) Depend on the resistance to leakage reactance ratio of each transformer

asked May 22, 2018 in Transformer by Shimroz123
1 answer 23 views

Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, respectively. Then the system frequency is (A) 50 Hz (B) 51 Hz (C) 51.25 Hz (D) 51.5 Hz

asked Apr 28, 2018 in Electrical Machine by Shimroz123
1 answer 9 views

When an NPN transistor is properly biased then most of the electrons from the emitter   (A) recombine with holes in the base (B) recombine in the emitter itself (C) pass through the base to the collector (D) are stopped by the junction barrier

asked May 17, 2018 in Power Electronics by Shimroz123
1 answer 372 views

Which phenomenon is present in thyristors but absent in BJT, MOSFET and IGBT ? (A) forward conduction (B) latching (C) forward blocking (D) reverse breakdown

asked Apr 28, 2018 in Power Electronics by Shimroz123
0 answers 129 views

FET is advantageous in comparison with BJT because of  A) High input impedance B) High noise C) High gain bandwidth product D) Its current controlled behavior

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 51 views
0 answers 30 views

The second break down in power BJT occurs due to (a) The first break down and the formation of hot spot inside (b) excessive collector current and low collector emitter voltage (c) excessive base current and high collector emitter voltage (d) none of thee above

asked Apr 14, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,530 questions

7,129 answers

135 comments

3,090 users

...