# In a single phase induction energy meter, in order to obtain true value of energy, the shunt

9 views

In a single phase induction energy meter, in order to obtain true value of energy, the shunt magnetic flux should lag behind the applied voltage by

(a) 90o (b) 0o (c) 45o (d) 60o

In a single phase induction energy meter, in order to obtain true value of energy, the shunt magnetic flux should lag behind the applied voltage by 90o

## Related questions

The disc of a single phase Induction-type energy meter makes 60 revolutions in 6 minutes. Meter Constant is 1200 rev/kWh. Power consumption in the load is (A) 1.2 kW (B) 1 kW (C) 600 W (D) 500 W

In a household single phase induction type wattmeter, the meter can be reversed by: - a) reversing the supply terminals b) reversing the load terminal c) opening the meter connection and reversing either the potential coil terminals or current coil terminals d) opening the meter and reversing the connection of both the potential coil terminals and current coil terminals

State the function and shape of following parts used in induction type energy meter: i) Series magnet ii) Shunt magnet iii) Al disc iv) Brake magnet

The current coil of a single-phase energy meter is wound on (a) One limb of the laminated core (b) Both the limbs of the laminated core with same number of turns (c) Both the limbs of the laminated core with different number of turns (d) The centre of the limb on the laminated core

The meter constant of a single-phase 230 V induction watt hour meter is 400 revolutions per kWh. The speed of the meter disc for a current of 10 A of 0.9 pf lagging will be

The meter constant of a single phase 240 V induction watt hour meter is 400 revolutions per KWhr. The speed of the meter disc for a current of 10 A of 0.8 pf, lagging will be  (A) 12.8 rpm (B) 16.02 rpm (C) 18.2 rpm (D) 21.1 rpm

A true rms reading voltmeter uses two thermocouple in order: -  a) to increase sensitivity b) that a second thermocouple cancels out the no linear effect of the first thermocouple c) to prevent drift in the dic. Amplifier d) all of the above

A single phase energy meter has a constant of 1200 revolution/kWh. When a load of 200 W is connected, the disc rotates at 4.2 revolutions per min. If the load is on for 10 hours, the meter records an excess of   (a) 0.1 kWh (b) 0.2 kWh (c) 1.0 kWh (d) 2.0 kWh

One single-phase energy meter operating on 230 V and 5 A for 5 hours makes 1940 revolutions. Meter constant is 400 rev/kWh. The power factor of the load is

In a single phase induction motor driving a fan load, the reason for having a high resistance rotor is to achieve (A) low starting torque (B) quick acceleration (C) high efficiency (D) reduced size

In a single-phase induction motor when the rotor is stationary and voltage is applied to the stator, then (A) the flux is constant (B) the flux first decreases and then increases in the same direction (C) the flux increases and decreases in the opposite direction with the same magnitude (D) current flows through the rotor

In order to have a lower cost of electrical energy generation the load factor  (1) and the diversity factor should be low (2) should be low but the diversity factor should be high (3) should be high but the diversity factor should be low (4) and the diversity factor both should be high

Starting torque can be obtained in the case of a single phase induction motor with identical main and auxiliary windings by connecting:  (1) A capacitor across the mains (2) A capacitor in series with the machine (3) A capacitor is series with the auxiliary winding (4) Equal value capacitors in series with the main and the auxiliary windings

If an energy meter disc makes 10 revolutions in 100 seconds when a load of 450W is connected to it, the meter constant in revolutions per kWh is  A) 1000 B) 500 C) 1600 D) 800

State the meaning of creeping error in 1 phase energy meter.

What is the value of form factor in connection with single phase alternating supply systems ? (A) 1.01 (B) 1.11 (C) 1.21 (0) 1.31

List any four errors in induction type energy meter. Give method of compensation for each.

In an induction type energy meter, the steady speed attained by the rotating disc is  1. Proportional to the deflecting torque. 2. Proportional to the resistance of the path of eddy currents. 3. Inversely proportional to the effective readings of disc from its axis. 4. Inversely proportional to the square of brake magnet flux.  Which of the above are correct ?

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

Damping torque used in energy meter is : - a) Electrostatic b) Electro magnetic c) Eddy Current d) None

In a single-phase induction motor, the operating direction is determined by the ________ A) Rotor B) Stator C) Starting circuit D) None of these

In a capacitor start single-phase induction motor, the capacitor is connected in:  (A) series with the main winding (B) series with the auxiliary winding (C) series with both the windings (D) parallel with the auxiliary winding .

Draw a neat sketch of 1-ph induction type energy meter and write operating principle of it.

An induction type energy meter is found to run fast. Correction for this error can be made by  (A) Over-load compensation. (B) Voltage compensation. (C) Moving the brake magnet away from the centre of the disc. (D) Moving the brake magnet towards the centre of the disc.

A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

For a single phase capacitor start induction motor, which of the following statements is valid?  A) The capacitor is used for power factor improvement B) The direction of rotation can be changed by reversing the main winding terminals C) The direction of rotation cannot be changed D) The direction of rotation can be changed by interchanging the supply terminals

The no~load current of a single phase induction motor is around _____% of full load current.  (1) 10 (2) 20 (3) 40 (4) 80

In a three-phase system, when the loads are perfectly balanced, the value of neutral current is equal to: A. Zero B. One-third of the maximum value C. Two -third of the maximum value D. The maximum value

In a second order system the value of resonant peak will be unity when the damping ratio has a value of  A) Zero B) Unity C) 0.707 D) 0.414

What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

A single-phase transformer has a turns ratio of 1 :2 and is connected to a purely resistive load as shown in the figure. The magnetizing current drawn is 1A, and the secondary current is 1A. Ifcore losses and leakage reactances are neglected, the primary current is  A)1.41A B)2A C) 2.24A D)3A

A single transistor can be used to build which of the following digital logic gates : - a) AND gates b) OR gates c) NOT gates d) NAND gates

In slip-energy recovery scheme of converter-fed 3-phase induction motor, super synchronous speeds are possible by (A) injecting voltage into the stator (B) injecting voltage into the rotor (C) extracting voltage from the stator (D) extracting voltage from the rotor.

In the capacitor-start, capacitor-run single-phase induction motor (A) two capacitors are connected across the main winding (B) when the centrifugal switch opens, the permanent capacitor is left in the auxiliary winding circuit (C) when the centrifugal switch opens, the permanent capacitor is left in the main winding circuit (D) two capacitors are connected across the auxiliary winding.

In an induction motor if the flux density is reduced to one-half, of its normal value then the torque will  (1) reduce to one-half (2) reduce to one-fourth (3) remain unchanged (4) increase four times

A single-phase induction motor with only the main winding excited would exhibit the following response at synchronous speed  (A) Rotor current is zero (B) Rotor current is non-zero and is at slip frequency (C) Forward and backward rotating fields are equal (D) Forward rotating field is more than the backward rotating field