# Torque/weight ratio of an instrument indicates

9 views
Torque/weight ratio of an instrument indicates

(a) Selectivity (b) Accuracy (c) Fidelity (d) Sensitivity

Torque/weight ratio of an instrument indicates Sensitivity

## Related questions

The ratio of the primary to secondary voltage of a transformer is 2:1. The saving in the turns of weight of copper required if an autotransformer is used instead of two winding transformer is (1) 50% (2) 33.33% (3) 66.67% (4) 97%

A Voltage Controlled Oscillator (VCO) is an instrument : - a) whose frequency is dependent upon the amplitude of input signal b) whose frequency is independent upon the amplitude of input signal c) whose frequency is dependent upon the frequency of input signal d) none of the above

An overhead transmission line has a span of 260 m. The weight of the conductor is 0.68 kg/m. The maximum allowable tension in the line is 1550 kg. Maximum sag of the line should be (a) 5.8 m (b) 4.6 m (c) 2.7 m (d) 3.7 m

The weight of an aluminium conductor as compared to a copper conductor of identical cross-section, for the same electrical resistance, is?

Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

State the function of controlling torque in electrical measuring instrument.

The effect of stray magnetic fields on the actuating torque of a portable instrument is maximum when the operating field of the instrument and the stray fields are  A) Perpendicular B) Parallel C) Inclined at 60" D) Inclined at 30°

The deflecting torque of a moving coil instrument depends on (a) supply frequency (c) flux in the coil (b) inverse of area of coil (d) square of the voltage

Which of the following factors limit the deflection of the pointer of a PMMC instrument of about 90o?  1. Its damping mechanism  2. Linearity of magnetic field in which the coil moves  3. Control spring arrangement  4. Shape of pole shoe for the horse shoe magnet   Select the correct answer using the code given below:   (a) Only 1 and 3 (b) Only 2 and 4 (c) Only 2 and 3 (d) Only 1 and 4

Pointer of an analog ohmmeter reading close to zero, indicates the resistor being measured is: A. overheated B. shorted C. open D. reversed

In an AC. circuit, a low value of kVAR compared with kW indicates?

In the time response analysis of control system, Damping Ratio is given by - a) Actual damping / Critical damping b) Critical damping /Actual damping c) ( Sum of the Actual damping and critical damping) /Actual damping d)( Difference of the Actual damping and critical damping) / critical damping

Name the different torque and their function in measuring instrument.

In a portable instrument, the controlling torque is provided by  A) Spring B) gravity C) eddy currents D) all of the above

In a ratio detector: -  a) the linearity is worse than in a phase discriminator b) stabilization against signal strength variation is provided c) the output is twice that obtainable from a similar phase discriminator d) the circuit is the same as in a discriminator, except that the diode are reversed

Damping torque used in energy meter is : - a) Electrostatic b) Electro magnetic c) Eddy Current d) None

Which of the following instrument can be used for measuring speed of an aeroplane ? (A) orifice plate (B) hot wire anemometer (C) rotameter (D) pitot tube

The moving system of an indicating type of electrical instrument is subjected to (a) a deflecting torque (b) a controlling torque (c) a damping torque (d) All of the above

In the case of an instrument reading of 8.3 V with a 0 to 150 voltmeter having a guaranteed accuracy of 1% full scale reading, the percentage limiting error is   (A) 1.810% (B) 0.181% (C)12.45% (D) 0.0018%

An analog voltmeter has a sensitivity of 10kΩ/volt. The galvanometer used in constructing the instrument will produce a full scale deflection when the current passed through it is  (a) 10 mA (b) 20 mA (c) 50 mA (d) 100 μA

A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is (A) 1 Ω (B) 1.001 Ω (C) 0.5 Ω (D) 10 Ω

The percentage limiting error, in the case of an instrument reading of 8.3V with a 0 to 150V voltmeter having a guaranteed accuracy of 1% full-scale reading is

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

The duty ratio of a step-up chopper with an output voltage of 200 V from a 80 V dc source, is (A) 0.4 (B) 0.5 (C ) 0.6 (D) 1.5

The ratio of rotor output to rotor input in an induction motor is 0.96. The slip of the motor is (a) 0.04% (b) 4% (c) 6% (d) 12%

An auto transformer having a transformation ratio of 0.8 supplies a load of 10 kW. The power transferred inductively from the primary to secondary is (a) 2 kW (b) 4 kW (c) 8 kW (d) 10 kW

Specific energy consumption of an electric train is the ratio between (A) Specific energy output at driving wheels and efficiency of the traction motor (B) Specific energy output at driving wheels and efficiency of the transmission gear (C) Specific energy output of driving motor and efficiency of the driving wheels (D) Specific energy output at driving wheels and efficiency of the (motor + transmission gear)