17 views
in Power Electronics by
In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is 

 (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V 

1 Answer

0 votes
by

In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is 233.91 V

Related questions

1 answer 13 views

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt

asked May 13, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 13 views

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

asked May 22, 2018 in Electrical Engineering by Shimroz123
0 answers 86 views

 When The dc converter in figure shown has a resistance load of R = 10 Ω and the input voltage is Vs 220 V the converter switch remains on, its voltage drop is Vo -2 V. The chopping frequency is fI K sW Vs If the duty cycle is 50%, determine: (a) the average output voltage V (b) the RMS output voltage Vo (c) the converter efficiency (d) the effective input resistance of the converter

asked Apr 26 by Hussein
1 answer 7 views

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

asked 6 days ago in Elements of Electronics by Shimroz123
0 answers 49 views

A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load. For a firing angle of 60° for the SCR, the average output voltage is   (a) 240/π (b) 400/π (c) 300/π (d) 200/π 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

If the input to a differentiating circuit is a saw-tooth wave, then output will be …………….. wave: A) square B) rectangular wave C) triangular wave D) rectified sine wave

asked Jun 4, 2018 in Power Electronics by Shimroz123
0 answers 20 views

The duty ratio of a step-up chopper with an output voltage of 200 V from a 80 V dc source, is (A) 0.4 (B) 0.5 (C ) 0.6 (D) 1.5 

asked Jun 4, 2018 in Power Electronics by Shimroz123
1 answer 77 views

In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: (1) 50 Hz (2) 100 Hz (3) 150 Hz (4) 200 Hz

asked May 29, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: (1) 30 V (2) 60 V (3) 15 V (4) 10 V

asked May 28, 2018 in Electronics Engineering by Shimroz123
1 answer 9 views

The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is (A) 1200 Hz (B) 600 Hz (C) 100 Hz (D) 50 Hz 

asked Apr 23, 2018 in Instrumentation and control by Shimroz123
0 answers 18 views

For an 8 bit DAC, reference voltage is 10 V. If input to DAC starting from MSB is 10111100, output (in volts) is  A) 5.8 B) 6.4 C) 7.3 D) 8.2

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 37 views

 An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 20 views

The input frequency of a bridge rectifier is 50 its output frequency will be  1. 25 Hz 2.50 Hz 3.75 Hz 4. 100 Hz

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 24 views

In a balanced 3 -phase 200 V circuit, the line current is 115.5 A. When the power is measured by two wattmeter method, one of the wattmeters reads 20 kW and the other one reads zero. What is the power factor of the load ?

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
1 answer 79 views

A 3-phase voltage source inverter operates in 180° conduction mode with a star connected resistive load. If input dc voltage is 100 V, then the peak to peak output line voltage is :

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 7 views

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

asked 6 days ago in Elements of Electronics by Shimroz123
1 answer 17 views

Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

asked Sep 5, 2018 by Shimroz123
1 answer 7 views

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 8 views

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

asked May 23, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 33 views

If the load p.f. is 0.866, then the average p.f. the v-bank is  1. 0.886  2. 0.75  3. 0.51  4. 0.65 

asked May 13, 2018 in Electrical Engineering by Shimroz123
0 answers 70 views

The power in a 3-phase load is measured by two watt meters. If one watt meter reads zero, then the load power factor is (A) Zero (B) 0.5 (C ) 0.866 (D) unity 

asked Jun 4, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 21 views

A 3-phase voltage source inverter is operated in 180o conduction mode. Which one of the following statements is true ?  (A) Both pole-voltage and line-voltage will have 3rd harmonic components (B) Pole-voltage will have 3rd harmonic component but line-voltage will be free from 3rd harmonic (C) Line-voltage will have 3rd harmonic component but pole-voltage will be free from 3rd harmonic (D) Both pole-voltage and line-voltage will be free from 3rd harmonic components

asked May 18, 2018 in Power Electronics by Shimroz123
1 answer 23 views

If a capacitance is charged by a square wave current source, then the voltage across the capacitor will be (a) Square wave (b) Step function (c) Triangular wave (d) Zero

asked May 25, 2018 in Capacitance by Shimroz123
1 answer 9 views

In a full wave rectifier the negative point in a circuit is   (A) cathode (B) anode (C) The central tap on the high voltage secondary (D) plate.

asked May 17, 2018 in Power Electronics by Shimroz123
1 answer 13 views

A 3-phase induction motor is running at slip ‘s’. If its two supply leads are interchanged, then the operating slip at that instant will be:

asked May 22, 2018 in Induction Machine by Shimroz123
1 answer 18 views

If a 3-phase, 400V, 50Hz, 4 pole induction motor is running at a slip of 5% then the relative speed of rotor field with respect to stator filed is:

asked May 22, 2018 in Induction Machine by Shimroz123
0 answers 17 views

The phase sequence of a 3 phase alternator is RBY. If the direction of rotation of field is reversed, then which of the following can be the phase sequence ? (A) RBY (B) BYR (C) BRY (D) YRB

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

If the supply frequency of a 3-phase induction motor is ‘f’, then frequency of rotor emf at motor slip ‘s’ will be   (a) sf (b) (1 – s)f (c) f/s (d) None of these 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 7 views

Ripple factor for a half wave rectifier is  a. 1.65 b. 1.45 c. 1 d. 1.21 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 45 views

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

asked Aug 12, 2018 in Basic electrical and electronics engineering by Quiz
1 answer 14 views

The average value of a 12 V peak sine wave over one complete cycle is? A.0 V B.1.27 V C.7.64 V D.6.37 V

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 54 views

If a transformer primary is energised from a square wave voltage source, its output voltage will be a:  (A) square wave (B) sine wave (C) triangular wave (D) pulse wave

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 11 views

A single-phase half-controlled rectifier is driving a separately excited dc motor. The dc motor has a back emf constant of 0.5 V/rpm. The armature current is 5 A without any ripple. The armature resistance is 2 Ohm. The converter is working from a 230 V, single-phase ac source with a firing angle of 30o . Under this operating condition, the speed of the motor will be  (A) 339 rpm (B) 359 rpm (C) 366 rpm (D) 386 rpm

asked May 18, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 48 views

The output voltage waveform of a three-phase square-wave inverter contains  (A) only even harmonics (B) both odd and even harmonic (C) only odd harmonics (D) only triple harmonics

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 17 views

A single phase full-wave half-controlled bridge converter feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode.  (A) because the converter inherently does not provide for free-wheeling (B) because the converter does not provide for free-wheeling for high ... the AC supply (D) or else if a gate pulse to one of the SCRs is missed, it will subsequently cause a high load current in the other SCR.

asked May 18, 2018 in Power electronics converters by Shimroz123
0 answers 33 views

What is the Output voltage of Op-amp for input voltage of Vi1=150 μV,Vi2=140 μV if the amplifier has differential gain of Ad=4000 and value of CMRR is 100. 

asked Apr 4, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

At a particular instant, the R-phase voltage of a balanced 3-phase system is + 30 V, and the Y-phase voltage is – 90 V. The voltage of B-phase at that instant is (A) + 120 V (B) – 120 V (C) – 60 V (D) + 60 V

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 40 views

In an induction motor if the flux density is reduced to one-half, of its normal value then the torque will  (1) reduce to one-half (2) reduce to one-fourth (3) remain unchanged (4) increase four times

asked May 1, 2018 in Electrical Machine by Shimroz123
1 answer 15 views

In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is :

asked Apr 29, 2018 in Electrical Machine by Shimroz123
0 answers 16 views

A 3 Phase, 60 Hz generator connected in Y connection, generates a line to line voltage of 23900 V. Calculate the peak line voltage.  (A) 13800 V (B) 33800 V (C) 42300 V (D) 23900 V 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?  (a) 100 VAR (b) 200 VAR (c) 300 VAR (d) 400 VAR

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
1 answer 12 views

A single phase transformer is designed to operate from 50 Hz, 1100 V supply and to have an output voltage of 240 V at no load. The core has mean area of 30 cm2 and the flux density has not to exceed 1.3T. The number of secondary turns will be (a) 1270 (b) 1017 (c) 768 (d) 277  

asked May 25, 2018 in Single phase transformer by Shimroz123
0 answers 20 views

If two 3-phase transformers with unequal voltage ratios are connected in parallel, the result is (A) circulating current on no-load (B) no circulating current on no-load (C) dead short-circuit (D) equal no-load secondary emfs 

asked Jun 4, 2018 in Electrical Machine by Shimroz123
1 answer 66 views

A single-phase voltage source square -wave inverter feeds pure inductive load. The waveform of the load current will be

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 10 views
0 answers 14 views

An average reading digital multimeter reads 10 V when fed with a triangular wave, symmetric about the time axis. For the same input the r.m.s. reading meter will read

asked May 25, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 22 views

In an amplitude modulated wave. the value of V is max 10V and Vmin is 5V, then % modulation is : (A) 25% (B) 33.3% (C) 50% (D) 100%

asked Apr 14, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...