25 views
in Power Electronic Controlled Drives by
A DC chopper is used for regenerative braking of a separately excited DC motor. The DC supply voltage is 400V. The armature current during regenerative braking is kept constant at 300 A with negligible ripple. For a duty cycle of 60% the power return to the DC supply is 

(a) 78 kW (b) 58 kW (c) 38 kW (d) 48 kW

1 Answer

0 votes
by

A DC chopper is used for regenerative braking of a separately excited DC motor. The DC supply voltage is 400V. The armature current during regenerative braking is kept constant at 300 A with negligible ripple. For a duty cycle of 60% the power return to the DC supply is  48 kW

Related questions

0 answers 24 views

A separately excited dc motor is required to be controlled, from a 3-phase supply, for its operation in the first quadrant only. The most preferred converter would be  (a) 3-phase fully controlled converter (b) 3-phase fully controlled converter with free wheel diode (c) 3-phase dual converter (d) 3-phase half wave converter 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 56 views

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) inversely proportional to α and Φ (C) directly proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 19 views

The supply both to field and armature circuits are disconnected simultaneously in a separately excited dc motor and it comes to a standstill in 5 sec. If the armature circuit of this motor is disconnected from supply with field circuit remaining energized, the motor would come to rest in (1) 5 sec (2) 7 sec (3) 4 sec (4) A very long time  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 11 views

A single-phase half-controlled rectifier is driving a separately excited dc motor. The dc motor has a back emf constant of 0.5 V/rpm. The armature current is 5 A without any ripple. The armature resistance is 2 Ohm. The converter is working from a 230 V, single-phase ac source with a firing angle of 30o . Under this operating condition, the speed of the motor will be  (A) 339 rpm (B) 359 rpm (C) 366 rpm (D) 386 rpm

asked May 18, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 16 views

A separately excited dc motor operating in first quadrant is fed from 3-phase semi -converter free -wheeling diode is open circuited, then the motor :  (A) can be operated in first quadrant (B) can be operated in first & second quadrants (C) can be operated in first & fourth quadrants (D) cannot be operated

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and armature resistance are 100 volt and 0.5Ω respectively. With the magnitude control ratio 0.6, the quadrant of operation DC motor is  (a) First (b) Second (c) Third (d) Fourth

asked May 15, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 35 views
2 answers 140 views

Separately Excited DC motor

asked Aug 9, 2017 in Electrical Machine by Zeeshan
1 answer 26 views

Explain regenerative braking for D.C. series motor.

asked Oct 12, 2018 in Industry Electrical Systems-II by Shimroz123
0 answers 8 views

A separately excited dc generator is running at rated speed and at no load. If its field winding is suddenly connected to a dc source then rise in armature generated voltage is governed by (1) Armature time constant (2) Field time constant (3) Both (a) and (b) (4) Mechanical time constant

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

In a regenerative braking, which of the following is generally true?  (a) Back e.m.f. in the motor exceeds the applied voltage (b) Back e.m.f. is less than the applied voltage (c) Kinetic energy of the motor is dissipated in a resistance (d) Kinetic energy of the motor is dissipated through free wheeling diode across the motor 

asked May 15, 2018 in Electrical Machine by Shimroz123
0 answers 19 views

A separately excited d.c. motor fed from single phase full converter with firing angle 60° runs at 1000 r.p.m. If motor is connected to single phase semiconverter with the same firing angle of 60°, it would run at (a) 2000 rpm (b) 1850 rpm (c) 1500 rpm (d) 1000 rpm 

asked May 25, 2018 in DC motor by Shimroz123
1 answer 20 views

what is separately excited motor ?

asked Aug 15, 2017 in Electrical Machine by Zeeshan
0 answers 18 views

The method of speed control used for increasing the speed of a dc shunt motor above its rated speed is  1) armature resistance control 2) field control (3) armature voltage control (4) series parallel control 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 11 views

Regenerative breaking of ac-dc converter fed dc motor is possible when firing delay angle of SCRs is (A) 30° (B) 60° (C ) 90° (D) 120°

asked Jun 4, 2018 in Electrical Machine by Shimroz123
1 answer 28 views

A separately excited d.c. machine is coupled to a 50 Hz, three-phase, 4-pole induction machine as shown in the figure. The Dc machine is energized first and the machines rotate at 1 600 1pm. Subsequently the induction machine is also connected to a 50 Hz, three phase source, the phase sequence being consistent with the direction of rotation. In steady state

asked May 20, 2018 in DC machine by Shimroz123
1 answer 46 views
0 answers 9 views

Two wattmeter method can be used in a three phase system excited with balanced three phase supply  A) To measure real power and power factor in a balanced load B) To measure reactive power in a balanced load C) To measure real power in an unbalanced load D) All of the above 

asked Apr 9, 2018 in Electrical Engineering by Zeeshan
0 answers 20 views

The duty ratio of a step-up chopper with an output voltage of 200 V from a 80 V dc source, is (A) 0.4 (B) 0.5 (C ) 0.6 (D) 1.5 

asked Jun 4, 2018 in Power Electronics by Shimroz123
1 answer 39 views

A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while the chopper feeds an RL load. The per unit current ripple would  (1) increase progressively  (2) decrease progressively  (3) decrease to a minimum value at α = 0.5 and then increase  (4) increase to a maximum value at α = 0.5 and then decrease

asked Apr 30, 2018 in Power Electronics by Shimroz123
1 answer 27 views

For using regenerative breaking, the most suitable motor is :  (A) DC series motor  (B) Slip ring induction motor  (C) Squirrel cage induction motor  (D) Synchronous motor

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 23 views

The slight curvature at the lower end of the O.C.C. of a self-excited dc generator is due to  1. residual pole flux 2. high armature speed 3.magnetic inertia 4. high field circuit resistance

asked May 13, 2018 in DC generator by Shimroz123
1 answer 8 views

Regenerative braking can: (A) be used for stopping a motor (B) not be easily applied to DC series motors (C) be easily applied to DC shunt motors (D) not be used for heavy duty -cycle motors

asked Apr 11, 2018 in Computer Engineering by Shimroz123
0 answers 18 views

The dc motor used for intermittent high torque loads is  (1) dc series motor (2) dc shunt motor (3) differential compound motor (4) cumulative compound motor

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

asked May 23, 2018 in Power Electronic Controlled Drives by Shimroz123
0 answers 21 views

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 30 views

Aluminium is not used as winding wire for the armature of a dc machine because  (1) aluminium has low resistivity (2) a large winding space is taken by aluminium conductors and creates jointing problems (3) the thermal conductivity of aluminium is low (4) aluminium has low conductivity as compared to copper

asked Apr 29, 2018 in Electrical Machine by Shimroz123
1 answer 22 views

The stator of a 415V, 50 Hz, 4-pole slip ring Induction Motor is excited by rated frequency with slip rings open circuited. The rotor is made to rotate at a speed of 600 rpm in the opposite direction to the normal direction, The frequency of induced voltage across slip ring is A) 30 Hz B) 70 Hz C) 20 Hz D) 35 Hz

asked Jun 17, 2018 in Induction Machine by Shimroz123
0 answers 41 views

A 0.5 Hp, 6 pole wound rotor induction motor is excited by a 3 phase 60 Hz source. Calculate the frequency of the rotor current at standstill.  (A) 50 Hz (B) 30 Hz (C) 60 Hz (D) 120 Hz 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 97 views

"DC series motor is used for traction purpose." Justify your answer with any six characteristics.

asked Oct 12, 2018 in Industry Electrical Systems-II by Shimroz123
0 answers 28 views

Why DC motor is used for traction?

asked Mar 11, 2018 in Utilization of electrical energy by Quiz
1 answer 18 views

A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the losses, the power factor of the ac mains at half the rated speed is  (A) 0.354 (B) 0.372 (C) 0.90 (D) 0.955

asked May 18, 2018 in Power electronics converters by Shimroz123
0 answers 26 views

To Charge a 120 V battery from a 600 V DC source using a DC chopper, The average battery current should be 20 A, with a peak to peak ripple of 2 A. If the chopper frequency is 200 Hz, calculate the duty cycle.  (A) 0.2 (B) 0.1 (C) 0.5 (D) 0.6 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

A dc series motor when connected across an AC supply will (1) Develop torque in same direction (2) Not develop any torque (3) Draw dangerously high current (4) Develop a pulsating torque 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

for the voltage built-up a self-excited D.C. generator, which of the following is not an essential condition.  1.there must be some residual flux  2.field winding mmf must aid the residual flux  3.total field circuit resistance must be less than t critical value  4.armature speed must be very high

asked May 13, 2018 in DC generator by Shimroz123
0 answers 24 views

Which type of starter is used to start the DC motor?

asked Mar 15, 2018 in Electrical Engineering by Quiz
1 answer 80 views

Consider a circuit with three parallel branches connected across a DC supply. What is the ratio of the branch currents I1 : I2 : I3 if the branch resistances are in the ratio of 2 : 3 : 4 respectively? A) 2 : 3 : 4 B) 6 : 4 : 3 C) 4 : 3 : 2 D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

In a 4-pole wave winding connected dc motor, the cross-magnetizing AT/pole for a brush shift of θ radians (A) Armature amp-conductors × (θ/360o) (B) Armature amp-turns × (θ/360o) (C) Armature amp-conductors × (1/4 - θ/360o) (D) Armature amp-conductors × (1/8 - θ/360o)

asked Apr 28, 2018 in Electrical Engineering by Shimroz123
0 answers 58 views

To enable dc series motor work satisfactory with an AC supply, the following modifications should be done (1) The yoke and poles should be completely laminated (2) The poles should be made of laminated steel (3) The air gap between stator and rotor be reduced (4) Compensating poles should be introduced  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

The direction of rotation of an inverter fed 3-phase ac motor is reversed by (A) a mechanical reversing switch (B) reversing the input dc link voltage (C) operating the inverter as a rectifier (D) changing the sequence of switching

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
0 answers 9 views

 Which of the following generators is used for DC arc welding application ? (A) Series generator (B) Shunt generator (C) Differential compound generator (D) Over -compound generator

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 52 views

In electric traction for a trapezoidal speed-time curve, the time period is (A) free running speed period = constant speed period (B) free running period = coasting period (C) free running period + coasting period = constant speed period (D) average speed period = scheduled speed period

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 28 views

If the load of the normally excited synchronous motor is increased the power factor will?

asked Mar 18, 2018 in Synchronous machine by Shimroz123
1 answer 22 views

If the field of synchronous motor is under excited, power factor will be?

asked Mar 18, 2018 in Synchronous machine by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,084 users

...