14 views
in Electronics Engineering by
The time constant of an RC circuit is defined as the time taken by the voltage across the capacitor to become_____ of its final value 

 (a) 63.2% (b) 36.8% (c) 50% (d) 100%  

1 Answer

0 votes
by

The time constant of an RC circuit is defined as the time taken by the voltage across the capacitor to become 63.2% of its final value 

Related questions

1 answer 18 views

The time constant of the capacitance circuit is defined as the time during which voltage?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

Time constant of a circuit is the time in seconds taken after the application of voltage to each?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 9 views

What is the time constant of an RC series circuit?  (A) R/C (B) C/R (C) 1/RC (D) RC

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 24 views

Circuit turn-off time of an SCR is defined as the time  (A) taken by the SCR turn to be off (B) required for the SCR current to become zero (C) for which the SCR is reverse biased by the commutation circuit (D) for which the SCR is reverse biased to reduce its current below the holding current

asked May 18, 2018 in Power Electronics by Shimroz123
1 answer 21 views

Time constant for RC circuit formula τ = RC Where, τ = time constant

asked Jul 2 in Formulas by Shimroz123
1 answer 15 views

The time constant of a series R-C circuit is given by?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

A single phase CSI has capacitor C as the load. For a constant source current, the voltage across the capacitor is   (A) square wave (B) triangular wave (C) step function (D) pulsed wave

asked May 17, 2018 in Power electronics converters by Shimroz123
0 answers 21 views

A ramp voltage V(t)=100 V is applied to an RC differentiating circuit with R=5 kΩ and C=4 μF. The maximum output voltage is  (A) 0.2 V (B) 2 V (C) 10 V (D) 50 V

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

Time constant of an inductive circuit?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 33 views

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 13 views

If the load current and flux of a DC motor are held constant, and voltage applied across its armature is increased by 10%, its speed will:  (A) Decrease by 10%. (B) Remain unchanged. (C) Increase by 10%. (D) Increase by 20%. 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

In a series RC circuit, 12 V (rms) is measured across.the resistor and 15 V (rms) is measured across the capacitor. The value of rms source voltage is: A. 3 V B. 27 V C. 19.2 V D. 1.9 V

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: (1) 30 V (2) 60 V (3) 15 V (4) 10 V

asked May 28, 2018 in Electronics Engineering by Shimroz123
1 answer 61 views

In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C?

asked May 1, 2018 in Network Analysis by Shimroz123
1 answer 6 views

These self inductance of a circuit is defined as twice the work done against the induced e.m.f. on establishing unit current in the coil. If the current to be established in the coil is doubled, the work done against the induced e.m.f. will be  1. Doubled  2. Halved  3. four times  4. Quarter times 

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

The current from the stator of an alternator is taken out to the external load circuit through: (A) slip rings (B) commutator segments (C) solid connections (D) carbon brushes

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

What is the nature of supply current in parallel RC circuit with reference to the voltage?  (A) In phase (B) Lags by 90 degree (C) Leads by 90 degree (D) Compensates and becomes zero 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 14 views

In the snubber circuit used in a thyristor to limit the peak voltage overshoot applied across it damping ratio is taken as about  A) 0.14 B) 0.21 C) 0.36 D) 0.62

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 25 views

If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

In an AC circuit, the voltage across R, L and C are 30 V, 60 V and 20 V respectively. The applied voltage is (A) 70 V (B) 50 V (C) 60 V (D) 100 V

asked May 12, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

The time constant of the servo-mechanism can be decreased by

asked Apr 26, 2018 in Control System by Shimroz123
0 answers 15 views

The upper cut off frequency of a capacitive coupled RC amplifier is decided by  A) Input Coupling capacitance B) Transistor internal capacitances C) Output coupling capacitance D) Bypass capacitance

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 5 views

The time constant for the  given circuit is A) 1/9 S B) 1/4 S C) 4S D) 9S

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 12 views

Turn-on time of an SCR in series with RL circuit can be reduced by   (a) Increasing circuit resistance R (b) Decreasing R (c) Increasing circuit inductance L (d) Decreasing L 

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 34 views

The second harmonic distortion is defined as the A) Ratio of amplitude of second harmonic component in the output to that of the fundamental frequency B) Harmonic distortion due to only second harmonic component C) Sum of distortion of first and second harmonic components in the output 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 22 views

In a series RLC circuit, the rms value of voltage across the resistor is 30 V, across the inductor is 60 V and across the capacitor is 20 V. The rms supply voltage would be (A) 110 V (B) 10 V (C) 220 V (D) 50 V

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

In a feedback series regulator circuit, the output voltage is regulated by controlling the a. Magnitude of the I/P voltage b. Gain of the feedback transistor c. Voltage drop across the series pass transistor d. Reference voltage

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 13 views

Time constant of a capacitive circuit?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
1 answer 9 views

The transconductance of a JFET is computed at constant VDS by: (1) Ratio of change in Idto change of Vgs (2) Ratio of change inVgs to change ofId (3) Product of change in Vgs to change of Id (4) Ratio of change in Vds to change of Id

asked May 29, 2018 in Electronics Engineering by Shimroz123
0 answers 13 views

Which if the following operation is the easiest in terms of time as a resource  (1) Accessing an element (2) deletion of an element (3) Insertion of an element (4) creation of Array of given size 

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 11 views

Bandwidth of an RC coupled amplifier is 100 kHz. Two such amplifiers are connected in cascade.Resultant bandwidth(in kHz) is around  A) 200 B) 100 C) 60 D) 30

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 16 views

The time taken for a surge to travel a 600 km long overhead transmission line is?

asked Mar 27, 2018 in Power system by Shimroz123
1 answer 8 views

Slew rate is defined by: (1) di/dt(max) (2) dv/dt(max) (3) di/dt(min) (4) dv/dt(min) 

asked May 29, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

In a series RLC circuit at resonance, the magnitude of the voltage developed across the capacitor  A) Is always zero B) Can never be greater than the input voltage C) Can be greater than the input voltage, however, it is 90° out of phase with the input voltage D) Can be greater than the input voltage, and is in phase with the input voltage

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 23 views

If a capacitance is charged by a square wave current source, then the voltage across the capacitor will be (a) Square wave (b) Step function (c) Triangular wave (d) Zero

asked May 25, 2018 in Capacitance by Shimroz123
2 answers 196 views

What happens to current flow in a capacitive circuit when the DC voltage across the capacitor is approximately equal to the source voltage?

asked May 29, 2018 in Capacitance by Shimroz123
1 answer 30 views

A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

asked Apr 29, 2018 in Network Analysis by Shimroz123
1 answer 22 views

What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
0 answers 33 views

In case of load flow analysis one of the system buses is taken as swing bus (a) as reference bus (b) to compensate the system losses (c) both (a) and (b) (d) to reduce the system losses 

asked May 25, 2018 in Power system by Shimroz123
1 answer 49 views

An A.C. voltage is impressed across a pure resistance of 3.5 ohms in parallel with a pure inductance of impedance of 3.5 ohms?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 19 views

A resistor connected across the gate and cathode of an SCR in a circuit increases its (A) dv/dt rating (B) Holding current (C) Noise Immunity (D) Turn-off time

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by which part of the transformer?

asked Mar 19, 2018 in Transformer by Zeeshan
1 answer 16 views

When an additional resistor is connected across an existing parallel circuit, the total resistance: A. remains the same B. decreases by the value of the added resistor C. increases by the value of the added resistor D. decreases

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 18 views

 Gauge factor of strain gauge is defined as the ratio of per unit change in the ______.

asked May 29, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

The potential transformers Nominal Ratio is defined as the ratio of:

asked May 22, 2018 in Transformer by Shimroz123
1 answer 66 views

In a biased differential relay, the bias is defined as the ratio of  A) Number of turns of restraining coil and operating coil B) Operating coil current and restraining coil current C) Faulteurrent and operating coil current D) Fault current and restraining coil current

asked May 20, 2018 in Switchgear And Protection by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...