Can you help by answering this question?

Principle of "locality" is used in context of ...

8 views
in Power Electronic Controlled Drives by
The ripple factor of a bridge rectifier is 

1.0.48 2.0.812 3. 1.11 4. 1.21 

1 Answer

0 votes
by

The ripple factor of a bridge rectifier is 0.48

Related questions

1 answer 11 views

A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively   (a) 10A, 7.07A (b) 5A, 10A (c) 5A, 7.07A (d) 7.07A, 5A

asked May 13, 2018 in Electronics Engineering by Shimroz123
1 answer 8 views

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

asked May 23, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 7 views

Ripple factor for a half wave rectifier is  a. 1.65 b. 1.45 c. 1 d. 1.21 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 5 views

The transformer utilization factor of full wave bridge rectifier is   (A) 0.812 (B) 0.286 (C) 0.693 (D) 0.782

asked May 17, 2018 in Transformer by Shimroz123
1 answer 9 views

Define the term 'Ripple factor' for rectifier.

asked Sep 2, 2018 by Shimroz123
1 answer 13 views

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt

asked May 13, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
1 answer 9 views

The input frequency is 50 Hz. The ripple frequency in a 12 phase full wave rectifier is (A) 1200 Hz (B) 600 Hz (C) 100 Hz (D) 50 Hz 

asked Apr 23, 2018 in Instrumentation and control by Shimroz123
1 answer 56 views

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) inversely proportional to α and Φ (C) directly proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 20 views

The input frequency of a bridge rectifier is 50 its output frequency will be  1. 25 Hz 2.50 Hz 3.75 Hz 4. 100 Hz

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 16 views

A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component of input current will respectively be  (A) 31% and 6.8 A (B) 31% and 7.8 A (C) 66% and 6.8 A (D) 66% and 7.8 A

asked May 18, 2018 in Power electronics converters by Shimroz123
0 answers 22 views

A three phase diode bridge rectifier is fed from a 400 V rms, 50 Hz, three phase a.c. source. For the purely resistive load, the peak instantaneous output voltage is 

asked May 25, 2018 in Diode by Shimroz123
1 answer 137 views

Feedback factor at the frequency of oscillation of a Wien bridge oscillator is:  (1) 3 (2) 1/3 (3) 1/29 (4) 3/29

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 23 views

A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current, if the triggering angle is 30o, the input power factor will be  (A) 0.65 (B) 0.78 (C) 0.85 (D) 0.866

asked May 18, 2018 in Power Electronics by Shimroz123
1 answer 39 views

The dc current through each diode in a bridge rectifier equals : - a) the load current b) half the dc load current c) twice the dc load current d) one-fourth the dc load current

asked Apr 14, 2018 in Instrumentation and control by Shimroz123
1 answer 22 views

Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform. 

asked 6 days ago in Elements of Electronics by Shimroz123
1 answer 6 views

In a bridge rectifier  1. PIV has a value Vm 2. Centre tap of secondary is not required 3. Smaller transformer can be used 4. All 

asked May 13, 2018 in Electrical Engineering by Shimroz123
0 answers 42 views

We wish to build a 135 V, 20 A, DC power supply using a single phase bridge rectifier and an inductive filter. The peak to peak current ripple should be about 10%. If a 60 Hz AC source is available; Calculate the peak to peak current ripple.  (A) 19 A (B) 20 A (C) 2 A (D) 1 A 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

Sketch circuit diagram of bridge rectifier with LC filter. State function of each component.

asked Sep 2, 2018 by Shimroz123
1 answer 9 views

Define ripple factor and PIV of diode.

asked Sep 5, 2018 by Shimroz123
1 answer 6 views

Explain operation of series inductor filter and find out its ripple factor.

asked Sep 2, 2018 by Shimroz123
1 answer 8 views

The ripple factor in an LC filter.   (A) Increases with the load current (B) Increases with the load resistance (C) Remains constant with the load current (D) Has the lowest value

asked May 17, 2018 in Electronics Engineering by Shimroz123
1 answer 8 views

Name the type of rectifier for each of following feature : (i) Highest rectifier efficiency (ii) Highest form factor (iii) Two diode rectifier circuit (iv) PIV = 2Vm.

asked Sep 2, 2018 by Shimroz123
1 answer 7 views

The ripple content of load current of a converter feeding RL load is decided by  A) Load resistance alone B) Load inductance alone C) Both load resistance and load inductance D) Neither resistance nor inductance

asked May 20, 2018 in Power electronics converters by Shimroz123
1 answer 25 views

A DC chopper is used for regenerative braking of a separately excited DC motor. The DC supply voltage is 400V. The armature current during regenerative braking is kept constant at 300 A with negligible ripple. For a duty cycle of 60% the power return to the DC supply is  (a) 78 kW (b) 58 kW (c) 38 kW (d) 48 kW

asked May 13, 2018 in Power Electronic Controlled Drives by Shimroz123
2 answers 21 views

Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to:  (1) 1 (2) 0.5 (3) 0.75 (4) 0.33

asked May 22, 2018 in Electronics Engineering by Shimroz123
1 answer 8 views

Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 n sec. The maximum clock frequency is (a) 2.65 MHz (b) 6.25 MHz (c) 5.26 MHz (d) 6.52 MHz 

asked May 26, 2018 in Electronics Engineering by Shimroz123
1 answer 52 views

In electric traction for a trapezoidal speed-time curve, the time period is (A) free running speed period = constant speed period (B) free running period = coasting period (C) free running period + coasting period = constant speed period (D) average speed period = scheduled speed period

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 77 views

In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: (1) 50 Hz (2) 100 Hz (3) 150 Hz (4) 200 Hz

asked May 29, 2018 in Electronics Engineering by Shimroz123
0 answers 29 views

A UPS commonly has following parts : (i) rectifier (ii) inverter (iii) static switch Which of the following is true ?   (a) only (i) (b) only (i) and (ii) (c) (i), (ii) and (iii) (d) only (ii) and (iii) 

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

For speed control of ac drive, the preferred method using thyristors is  A) Phase control B) Integral cycle control C) Single pulse PWM control D) Sinusoidal PWM control

asked May 20, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 27 views

Specific energy consumption of an electric train is the ratio between (A) Specific energy output at driving wheels and efficiency of the traction motor (B) Specific energy output at driving wheels and efficiency of the transmission gear (C) Specific energy output of driving motor and efficiency of the driving wheels (D) Specific energy output at driving wheels and efficiency of the (motor + transmission gear)

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 20 views

The direction of rotation of an inverter fed 3-phase ac motor is reversed by (A) a mechanical reversing switch (B) reversing the input dc link voltage (C) operating the inverter as a rectifier (D) changing the sequence of switching

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 49 views

A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is

asked May 3, 2018 in Power Electronics by Shimroz123
1 answer 18 views

A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is (A) 9997 Ω (B) 10000 Ω (C) 997 Ω (D) 10003 Ω

asked Apr 28, 2018 in Power Electronic Controlled Drives by Shimroz123
1 answer 7 views

In a thyistorised converter a free wheeling diode is used to  A) Add to the conduction current ofthe thyristor B) Oppose the thyristor conduction C) Conduct current during the off period of the thyristor D) Protect the thyristor by providing a shunt path

asked May 20, 2018 in Power Electronic Controlled Drives by Shimroz123
0 answers 19 views

A modulo -6 ripple counter with J-K flip-flops uses at the clear input, the output from (a) NAND gate with QB,Qc as inputs (b) NAND gate with QA, Q8 as inputs (c) NAND gate with QA, Qc as inputs (d) AND gate with QB, Qc as inputs

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 7 views

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

asked 6 days ago in Elements of Electronics by Shimroz123
1 answer 37 views

 An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 47 views

Rectification efficiency of a full wave rectifier without filter is nearly equals to:  (1) 51% (2) 61% (3) 71% (4) 81%

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 15 views

In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: (1) 30 V (2) 60 V (3) 15 V (4) 10 V

asked May 28, 2018 in Electronics Engineering by Shimroz123
1 answer 25 views

When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

asked Apr 29, 2018 in Power Electronics by Shimroz123
1 answer 13 views

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

asked May 22, 2018 in Electrical Engineering by Shimroz123
0 answers 11 views

A single-phase half-controlled rectifier is driving a separately excited dc motor. The dc motor has a back emf constant of 0.5 V/rpm. The armature current is 5 A without any ripple. The armature resistance is 2 Ohm. The converter is working from a 230 V, single-phase ac source with a firing angle of 30o . Under this operating condition, the speed of the motor will be  (A) 339 rpm (B) 359 rpm (C) 366 rpm (D) 386 rpm

asked May 18, 2018 in Bipolar Junction Transistor by Shimroz123
1 answer 9 views

In a full wave rectifier the negative point in a circuit is   (A) cathode (B) anode (C) The central tap on the high voltage secondary (D) plate.

asked May 17, 2018 in Power Electronics by Shimroz123
1 answer 17 views

In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is   (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V 

asked May 13, 2018 in Power Electronics by Shimroz123
0 answers 12 views

If the filter capacitance is increased, the ripple will (a) remain same (b) increase (c) decrease (d) be zero

asked May 25, 2018 in Capacitance by Shimroz123
1 answer 12 views

In static Kramer drive, motor turns ratio is 0.6, the firing angle is 120o. The motor slip is   (a) 0.633 (b) 0.533 (c) 0.833 (d) 0.733 

asked May 13, 2018 in Power Electronic Controlled Drives by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...