# Pinch off voltage of a J FET is the drain to source voltage above which drain current.

12 views
Pinch off voltage of a J FET is the drain to source voltage above which drain current.

• Increases

• Decreases

• Remains constant

• Becomes zero

Pinch off voltage of a J FET is the drain to source voltage above which drain current Remains constant

## Related questions

Define pinch off voltage and drain resistance of FET.

Which of the following theorems enables a number of voltage (or current) source to be combined directly into a single voltage (or current) source. (1) compensation theorem (2) reciprocity theorem (3) superposition theorem (4) Millman's theorem

What is meant by pinch off voltage in MOSFET?

A series R-L circuit is suddenly connected to d.c. voltage source of V volts. The current in this series circuit, just after the switch is closed, is equal to (1) Zero (2) V/L (3) V/C (4) V.L/C

In a JFET drain current is maximum when VGS is  (a) zero (b) negative (c) positive (d) equal to Vp

For a JFET, drain saturation current is 10 mA with Vdd=10 V, Vp= -5V and Vgs= -2 V, drain current in mA is  A) 12.5 B) 8.4 C) 6.2 D) 3.6

The zero sequence current of a generator for line to ground fault is j 2.4 p.u. The current through the neutral during the fault is (a) j 0.8 p.u (b) j 2.4 p.u. (c) j 0.24 p.u. (d) j 7.2 p.u.

Velocity of an electron (in km/S) starting at rest and travelling to a point 100 V above the starting potential is around  A) 3600 B) 4000 C) 5100 D) 6000

Beta cut-off frequency of a transistor is the frequency at which the Beta is • 0.707 of low frequency value • Zero • Equal to low frequency value • None of the above.

A current controlled voltage source is equivalent to :  (A) series voltage feed -back amplifier (B) shunt current feed -back amplifier (C) shunt voltage feed -back amplifier (D) series current feed -back amplifier

A step voltage E is applied to a series R-L circuit. The rate of change of current is maximum at t = _:  (1) Zero (2) Infinity (3) L/R (4) R/L

The average power delivered to an impedance 4 − j 3 Ω by a current 5Cos(100πt + 100) Ampere is A) 44.2 W B) 50 W C) 62.5 W D) 125 W

A BJT’s voltage stand-off capability when the base current is zero (A) collector-emitter breakdown voltage (B) minimum collector-emitter voltage (C) collector-base breakdown voltage (D) emitter-base voltage

Does conventional current return to the positive or negative terminal of the voltage source?

A 3-phase voltage source inverter is operated in 180o conduction mode. Which one of the following statements is true ?  (A) Both pole-voltage and line-voltage will have 3rd harmonic components (B) Pole-voltage will have 3rd harmonic component but line-voltage will be free from 3rd harmonic (C) Line-voltage will have 3rd harmonic component but pole-voltage will be free from 3rd harmonic (D) Both pole-voltage and line-voltage will be free from 3rd harmonic components

A network that consists of at least a voltage source or current source is called A) Active network B) Ideal network C) Sourced network D) Outsourced network

Write the procedure of converting a given current source into voltage source.

A single-phase voltage source square -wave inverter feeds pure inductive load. The waveform of the load current will be

If a capacitance is charged by a square wave current source, then the voltage across the capacitor will be (a) Square wave (b) Step function (c) Triangular wave (d) Zero

The magnetic field intensity at the centre of a current carrying coil of diameter J m is K. The current flowing in the coil is

What is the output voltage of a battery if 12 J of energy is expended in moving 1 C of charge?

What is the output voltage of a battery if 6 J of energy is expended in moving 1 C of charge?

What is the output voltage of a battery if 10 J of energy is expended in moving 1.25 C of charge?

An emf of 120 V causes a current of 3A to flow in a circuit how much energy is supplied by the source in 12 seconds. A. 4130 J B. 4310 J C. 4320 J D. None of these

The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to: A. 27.2 mA B. 59 mA C. 5.9 mA D. 590 mA

A coil having 90 turns is connected to a 120 V, 60 Hz source. If the effective value of the magnetizing current is 4 A. Calculate the inductance of the coil.  (A) 79.6 mH (B) 121.2 mH (C) 32.2 mH (D) 83.16 mH

When a resistor R is connected to a current source, it consumes a power of 18 W. When the same R is connected to a voltage source having the same magnitude as the current source, the power absorbed by R is 4.5 W. The magnitude of the current source and the value of R are  (A) √18A and 1Ω (B) 3A and 2Ω (C) 1A and 18Ω (D) 6A and 0.5Ω

For measuring the frequency of an unknown A.C. source. Which of the following device is necessary to obtain a standard waveform?  (A) Operational amplifier (B) Astable multivibrator (C) Schmitt trigger (D) Monostable multivibrator

In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the (A) applied load (B) internal compensation (C) impedance of the source (D) power dissipation in the chip

FET belongs to which of the following type of device?  (A) Current controlled device (B) Magnetic device (C) Power controlled device (D) Voltage controlled device

As the wave frequency approaches to cut-off frequency of wave guide, the correct statement is : a. The phase velocity of waves tends to zero. b. The phase velocity of waves tends to velocity of light. c. The phase velocity of waves tends to infinite. d. None of these.

A single phase CSI has capacitor C as the load. For a constant source current, the voltage across the capacitor is   (A) square wave (B) triangular wave (C) step function (D) pulsed wave

Electrical shock happens for voltage/current?

In a series RLC circuit that is operating above the resonant frequency, the current : -  a) lags the applied voltage b) leads the applied voltage c) is in phase with the applied voltage d) is zero

The internal resistances of an ideal current source, and an ideal voltage source are, respectively, (A) 0, ∞ (B) ∞, ∞ (C) ∞, 0 (D) 0,0

A practical current source is usually represented by  a. A resistance in series with an ideal current source.  b. A resistance in parallel with an ideal current source.  c. A resistance in parallel with an ideal voltage source.  d. None of the above.

In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in (A) voltage notching (B) harmonic distortion (C) voltage sag (D) voltage swell

While biasing JFET if drain and source are interchanged, then (A) device will work normally (B) device will get damaged (C) device will work but value of drain current will affected (D) device will not operate at all

The upper cut off frequency of a capacitive coupled RC amplifier is decided by  A) Input Coupling capacitance B) Transistor internal capacitances C) Output coupling capacitance D) Bypass capacitance

The output voltage of a battery drops from 100 V with zero load current to 80 V when load current is 2 A. The internal resistance of the battery is (a) 10 Ω (b) 20 Ω (c) 40 Ω (d) 50 Ω

The transient current in lossless L-C circuit when excited from an AC source is, sine wave  (a) Critically damped (b) Underdamped (c) Overdamped (d) Undamped

In an energymeter which coil carries the current proportional to supply voltage _____.

A power system is subjected to a fault which makes the zero sequence component of current equal to zero. The nature of fault current is: A) Double line to ground fault B) Line to line fault C) Line to ground fault D) Three-phase to ground fault

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W