# A 4 bit counter is used to count from 0,1,2...n. Value of “n” is

8 views
A 4 bit counter is used to count from 0,1,2...n. Value of “n” is

A 4 bit counter is used to count from 0,1,2...n. Value of “n” is 15

## Related questions

1 answer 15 views

How many flip-flops are required to build a binary counter circuit to count from 0 to 1023 ? (a) 1 (b) 6 (c) 10 (d) 23

1 answer 8 views

Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 n sec. The maximum clock frequency is (a) 2.65 MHz (b) 6.25 MHz (c) 5.26 MHz (d) 6.52 MHz

1 answer 15 views

The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current? A. 30 A/s B. 20 A/s C. 10 A/s D. none of these

1 answer 23 views

The output Y of a 2-bit comparator is logic 1 whenever the 2-bit input A is greater than the 2-bit input B. The number of combinations for which the output is logic 1, is  (A) 4 (B) 6 (C) 8 (D) 10

1 answer 13 views

In a 5 bit weighted resistor D/A converters, the resistor value corresponding to LSB is 40 kΩ, and the resistor value corresponding to MSB will be (A) 0.4 kΩ (B) 3 kΩ (C) 2.8 kΩ (D) 2.5 kΩ

0 answers 14 views

By which of the following connections, one-bit binary counter can be obtained from a JK flip-flop?  A) J = K = 0 B) J = K = 1 C) J = K’ D) None of these

1 answer 34 views

Assuming 8 bits for data, 1 bit for parity, I start bit and 2 stop bits, the number of characters that 1200 BPS communication line can transmit is

1 answer 15 views
1 answer 8 views
1 answer 32 views

The number of comparators required in a 4 bit comparator type ADC is (A) 16 (B) 15 (C) 17 (D) 12

1 answer 25 views

The output of a JK flip-flop with asynchronous preset and clear inputs is ‘1’. The output can be changed to ‘0’ with one of the following conditions by applying A) J = 0, K = 0 and using a clock B) J = 1, K = 0 and using the clock C) Asynchronous preset input D) J = 1, K = 1 and using the clock

0 answers 15 views

If a variable can take only integer values from 0 to n, where n is a constant integer, then variable can be represented as a bit-field whose width is the integral part of (assume base 2)  (1) log(n) +1 (2) log(n + 1) + 1 (3) log(n – 1) + 1 (4) none of these

0 answers 15 views

Total numbers of ascending runs in the sequence 4 6 7 2 9 1 2 8 9 3 0  (1) 3 (2) 5 (3) 7 (4) 9

0 answers 107 views

Three materials X, Y and Z having relative permittivity 2.5, 3.0 and 4.0 respectively are used in a single core cable. The materials on inner most and outer most layer respectively should be (a) X and Y (b) Y and Z (c) X and Z (d) Z and X

1 answer 15 views

In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is :

0 answers 23 views

The emf induced in a coil is 1 volt when current in it changes from 0 to 100 mA in time 10mS. Its inductance (in mH) value is  A) 10 B) 50 C) 100 D) 1000

1 answer 19 views

Given a unity feedback system with G(s)=k/s (s+4), the value of k for damping ratio of 0.5 is

0 answers 17 views

The IC used for 2:1 multiplexer is (A) IC 74150 (B) IC 74151 (C) IC 74153 (D) IC 74157

1 answer 7 views

State the following, 1) Position of head light 2) Supply voltage for flasher light 3) Colours used for marker light 4) Frequencies for engine horn.

1 answer 17 views

Positive feedback is used in 1. Amplifier 2. Rectifier 3.Oscillator 4. Detector

1 answer 8 views

Parity bit check is used to

0 answers 26 views

An audit trail  (1) is used to make backup copies (2) is the recorded history of operations performed on a file (3) can be used to restore lost information (4) none of these

1 answer 15 views

The o/p of a 2 - input OR gate is 1 when its   1. both inputs are 1 2. both inputs are 0 3.either input is 1 4. either input is 0

1 answer 19 views

A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is

1 answer 14 views

A rectangular waveguide is 4.2 cm by 1.85 cm. The cut-off frequency of the dominant mode through this waveguide is  (a) 3.57 GHz (b) 3.75 GHz (c) 3.70 MHz (d) 3.57 MHz

1 answer 8 views

State the function of following components related to mimic diagram. 1) PL 2) OPL 3) CHL 4) GCK 5) LTK 6) ARK

1 answer 393 views

The number of comparators required in a 3-bit comparator type analog to digital converter is  A) 2 B) 3 C) 7 D) 8

1 answer 30 views

A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the input code 1010:  (1) 0.3125 V (2) 3.125 V (3) 0.78125 V (4) –3.125 V

1 answer 22 views

The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be  (A) 48.0% (B) 57.1% (C) 59.2% (D) 88.8%

0 answers 14 views

No. of flip-flops used in decade counter (a) 3 (b) 2 (c) 4 (d) None of these

1 answer 17 views

In a positive edge triggered JK flip-flop, J = 1, K = 0 and clock pulse is rising, Q will be (a) 0 (b) 1 (c) showing no change (d) toggle

0 answers 16 views

For a resonant circuit with resonant frequency of 1 MHz a, 0 = 50 and R = 400, find the value of C (A) 250 pF (B) 1000 pF (C) 1.25 pF (D) 500 pF

0 answers 46 views

For a balanced three phase star connected load for which line voltage is 230V and per phase resistance and reactance is 6 Ohm and 8 Ohm respectively. Calculate: 1) phase voltage 2) line current 3) power factor 4) total power absorbed

1 answer 11 views
0 answers 13 views

Which of the following sorts is quickest when sorting the following set: 1 2 3 5 4  (1) Quick Sort (2) Bubble Sort (3) Merge Sort (4) Heap Sort

0 answers 11 views

106 bytes of memory is called  (1) 1 KB (2) 1 MB (3) 1 GB (4) 1 TB

0 answers 19 views

230 bytes of memory is called  (1) 1 KB (2) 1 MB (3) 1 GB (4) 1 TB

0 answers 131 views

MSXML is  (1) A Microsoft language (2) XML parser that ships with Internet explorer 5.0 (3) Used for interacting with XML (4) None of these

1 answer 29 views

If eight -tenths coulomb passes a point in 4 s, the value of current is equal to: A. 1.6 A B. 16 A C. 2 A D. 0.2 A

1 answer 28 views

Assume that the n-channel MOSFET shown in figure is ideal and that its threshold voltage is +1 .0 V. The voltage Vab between nodes a and b is A)5V B)2V C)1V D)0V

0 answers 38 views

Which scanner can be used to image a 3-dimensional object?  (1) Drum (2) Slide/Film (3) Microfilm (4) Digital Camera

1 answer 9 views

When A = 0., B = 0, C = 1 then in two input logic gate we get gate  (A) XOR gate (B) AND gate (C) NAND gate (D) NOR gate

0 answers 20 views

The zero sequence current of a generator for line to ground fault is j 2.4 p.u. The current through the neutral during the fault is (a) j 0.8 p.u (b) j 2.4 p.u. (c) j 0.24 p.u. (d) j 7.2 p.u.

1 answer 20 views

At an industrial sub-station with a 4 MW load, a capacitor of 2 MVAR is installed to maintain the load power factor at 0.97 lagging. If the capacitor goes out of service, the load power factor becomes (A) 0.85 (B) 1.00 (C) 0.80 lag (D) 0.90 lag

0 answers 49 views

A high-pass filter has a resistance R = 2 kΩ The lowest input frequency to be passed is 7.5 kHz. The value of suitable coupling capacitor must be: A) 0.001 pico Farad B) 0.01 pico Farad C) 0.1 pico Farad D) 1 pico Farad

1 answer 62 views

If the inertia constant H of a machine of 200 MVA is 2 p.u., its value corresponding to 400 MVA will be   (a) 4 p.u. (b) 2 p.u. (c) 1.0 p.u. (d) 0.5 p.u.

0 answers 13 views

Calculate the resistance value in ohms for the following conductance values: (a) 0.001 S (b) 0.01 S (c) 0.1 S (d) 1 S.

1 answer 31 views
1 answer 13 views

An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of  A) 0.8 ohm in series with the meter B) 1.0 ohm in series with the meter C) 0.04 ohm in parallel with the meter D) 0.05 ohm in parallel with the meter

1 answer 31 views

A relay has a rating of 5 A, 2.2 sec IDMT and a relay setting of 125% TMS = 0.6. It is connected to a supply circuit through a C.T. 400/5 ratio. The fault current is 4000 A. The operating current of the relay is