# In a particular circuit connection, AWG 18 wire is selected over AWG 22. The reason is that it is having

12 views
In a particular circuit connection, AWG 18 wire is selected over AWG 22. The reason is that it is having

In a particular circuit connection, AWG 18 wire is selected over AWG 22. The reason is that it is having Higher current carrying capacity

## Related questions

You are measuring the current in a circuit that is operated on an 18 V battery. The ammeter reads 40 mA. Later you notice the current has dropped to 20 mA. How much has the voltage changed? A.9 V B.900 mV C.0 V D.18 V

In a 3 phase, 4 wire unbalanced System, the current in the neutral wire is 18 A. The magnitude of the zero sequence current is

In a single phase induction motor driving a fan load, the reason for having a high resistance rotor is to achieve (A) low starting torque (B) quick acceleration (C) high efficiency (D) reduced size

In a particular meter, the deflecting torque is directly proportional to the current flowing through it, the type of meter is (a) moving coil (b) moving iron (c) induction (d) electro-static

When a resistor R is connected to a current source, it consumes a power of 18 W. When the same R is connected to a voltage source having the same magnitude as the current source, the power absorbed by R is 4.5 W. The magnitude of the current source and the value of R are  (A) √18A and 1Ω (B) 3A and 2Ω (C) 1A and 18Ω (D) 6A and 0.5Ω

An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C

In short circuit calculations, the selected base kVA is equal to (A) That of the largest Plant (B) The total plant Capacity (C) Any arbitrary value (D) Can be any one of (A), (B), (C)

The cell reference fro a range of cells that starts in cell B1 and goes over to column G and down to row 10 is…  (1) B1-G10 (2) B1.G10 (3) B1;G10 (4) B1:G10

In a sample-and-hold circuit, the aperture time is (A) time required following a sample (B) time required for the switch to open (C) transition time interval between sample and hold (D) time from the hold command to the opening of the switch

In Print server which is a buffer that holds data before it is send to the printer.  (1) Queue (2) Spool (3) Node (4) Jobs

A sine wave voltage is applied across an inductor. When the frequency of the voltage is decreased, the current decreases.

The resistance of a few meters of wire conductor in closed electrical circuit is?

The color of wire recommended for earth connection as per BIS code is

State functions of ; i) Cable box ii) Guard wire iii) Shackle insulator iv) Stay wire used in service connection

The advantage of a semiconductor strain gauge cover the wire round strain gauge is that

A drawn wire of resistance 5 Ω is further drawn so that its diameter becomes one-fifth of the original. What is its resistance with volume remaining the same ? (a) 25 Ω (b) 125 Ω (c) 625 Ω (d) 3125 Ω

A depletion MOSFET differs from a JFET in the sense that it has no   (A) channel (B) gate (C) P-N junctions (D) substrate

A rheostat differs from potentiometer in the respect that it?

In a series RLC circuit that is operating above the resonant frequency, the current : -  a) lags the applied voltage b) leads the applied voltage c) is in phase with the applied voltage d) is zero

In the induction type directional over current relay, when a short-circuit occurs in the circuit (A) power flows in reverse direction (B) power flows in normal direction (C) directional power element does not operate (D) over current element is not energized

A Darlington transistor connection provides a transistor having a very large  a. Current gain b. Voltage gain c. Impedance gain d. Impedance matching gain

The biggest advantage of T-T connection over the V-V connection of 3-phase power transformation is that it provides.  1.a set of balanced voltages under load 2.a true 3-phase, 4-wire system 3.a higher ratio of utilization 4.more voltages

The switch in the circuit has been closed for a long time. It is opened at t = 0. At t = 0+, the current through the 1 micro farad capacitor is A) 0A B) 1A C) 1.25A D) 5A

If one of the control springs of PMMC ammeter is broken when it is connected in a circuit, the meter will read  A) Half the correct value of current B) Twice the correct value of current C) An indefinite figure D) Zero

Compare CC and PC of wattmeter on the basis of:- (i) Connection (ii) Status (iii) Number of turns (iv) Gauge of wire.

Earth coverage dish antenna is used in satellite system. It is characterized by the fact that  (a) It is a narrow beam antenna (b) It is Parabolic antenna (c) it is sharply focused within a small area of the surface of the earth (d) it is a wide angle antenna which covers a large area of the surface of the earth

A FET is preferred over an ordinary transistor because it  1. Permits high degree of isolation between input & output circuits 2. Has low noise level 3. Has very high power gain 4. Has all the above properties

For transmission line load matching over a range of frequencies, it is best to use a  (a) Balun (b) broadband directional coupler (c) double stub (d) single stub

The mechanism that bring a page into memory only when it is needed is called _____________  (1) Segmentation (2) Fragmentation (3) Demand Paging (4) Page Replacement

When the initial conditions of a system are specified to be zero it implies that the system is?

To couple a coaxial line to a parallel wire line, it is best to use a:  (1) A slotted line (2) Balun (3) Directional coupler (4) Quarter wave line transformer

AT-T connection has higher ratio of utilizax that n a V - V connection only when  1. Identical transformers are used  2. Load power factor is leading  3. Load power factor is unity  4. Non-identical transformers are used

Which of the following is true with a series circuit having resistors of different values? A) The total resistance of the circuit is the sum of the individual resistances B) The current across each resistor is the same C) The voltage drop across each resistor depends on the value of the resistor D) All the above

The voltage of a circuit is measured by a voltmeter having input impedance comparable with the output impedance of the circuit thereby causing error in voltage measurement. This error may be called as_________.

The input of an A.C. circuit having power factor of 0.8 lagging is 40 kVA The power drawn by the circuit is?

State the function of a contactor in a power circuit of locomotive. List different types of it and state one application of each.

In the snubber circuit used in a thyristor to limit the peak voltage overshoot applied across it damping ratio is taken as about  A) 0.14 B) 0.21 C) 0.36 D) 0.62

Is it true or false that electron flow and conventional current are in opposite directions?