7 views
in Basic concepts by
An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is

approximately?

A.385 ohms

B.38.5ohms

C.3.1 ohms

D.31 ohms

1 Answer

0 votes
by

An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is

approximately?

A.385 ohms

B.38.5ohms

C.3.1 ohms

D.31 ohms

Related questions

1 answer 17 views

An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately equal to: A. 385Ω B. 38.5Ω C. 3.1Ω D. 31Ω

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 159 views

A heating element of a hot plate on an electric cooking range draws 12 amperes from 240 V mains. How many kWh of energy will be consumed in one hour and 15 minutes 

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

A resistance of 3.3 M ohms is connected across a 500 V source. The resulting current is approximately? A.15.1 μA B.151 μA C.66 mA D.660 mA

asked May 15, 2018 in Basic concepts by Zeeshan
0 answers 14 views

A single phase motor draws a current of 5 A from a 120 V, 60 Hz line. The power factor of the motor is 65%. Calculate the active power absorbed by the motor.  (A) 600 W (B) 390 W (C) 456 W (D) 650 W 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 22 views

The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be  (A) 48.0% (B) 57.1% (C) 59.2% (D) 88.8%

asked May 17, 2018 in Electrical Machine by Shimroz123
1 answer 20 views

How much resistance is required to limit the current from a 12 V battery to 3.6 mA? A.3.3 k ohms B.33 k ohms C.2.2 k ohms D.22 k ohms

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 20 views

When resistance element of a heater fuses and then we reconnect it after removing a portion of it, the power of the heater will?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 14 views

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 10 views

If a 220 V heater is used on 110 V supply, the heat produced by it will be nearly (a) one half (b) twice (c) one-fourth (d) four times 

asked May 25, 2018 in Electrical Engineering by Shimroz123
1 answer 26 views

Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 28 views

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

asked May 22, 2018 in Transformer by Shimroz123
1 answer 24 views

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be; (A) 3.6 (B) 2.5 V (C) 3.0 V (D) 6.0 V

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 20 views

The duty ratio of a step-up chopper with an output voltage of 200 V from a 80 V dc source, is (A) 0.4 (B) 0.5 (C ) 0.6 (D) 1.5 

asked Jun 4, 2018 in Power Electronics by Shimroz123
1 answer 19 views

How much resistance is needed to draw 17.6 mA from a 12 volt source? A.212 ohms B.6.8 kohms C.68 ohms D.680 ohms

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 18 views

A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high load inductance. The input displacement factor (IDF) and the input power factor (IPF) of the converter will be  (A) IDF IPF = = 0.867; 0.828 (B) IDF IPF = = 0.867; 0.552 (C) IDF IPF = = 0.5; 0.478 (D) IDF IPF = = 0.5; 0.318 

asked May 18, 2018 in Power electronics converters by Shimroz123
1 answer 49 views

An A.C. voltage is impressed across a pure resistance of 3.5 ohms in parallel with a pure inductance of impedance of 3.5 ohms?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 41 views

A 0.5 Hp, 6 pole wound rotor induction motor is excited by a 3 phase 60 Hz source. Calculate the frequency of the rotor current at standstill.  (A) 50 Hz (B) 30 Hz (C) 60 Hz (D) 120 Hz 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 24 views

The primary coil of a transformer is connected to a 60 V ac source. The secondary coil is connected to a 330 ohms load. The turns ratio is 3:1. What is the secondary voltage? A.2 V B.20 V C.180 V D.18 V

asked May 15, 2018 in Basic concepts by Zeeshan
1 answer 33 views

A large dc motor is required to control the speed of the blower from a 3 -phase ac source. The suitable ac to dc converter is, 3 -phase (a) Fully controlled bridge converter (b) Fully controlled bridge converter with freewheeling diode (c) Half controlled bridge converter (d) Converter pair in sequence control

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

The current through a flashlight bulb is 40 mA and the total battery voltage is 4.5 V. The resistance of the bulb is approximately? A.112 ohms B.11.2 ohms C.1.2 ohms D.18 ohms

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 19 views

A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is (A) 2.5 W (B) 5 W (C) 32.5 W (D) 35 W

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 21 views

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be?

asked Mar 25, 2018 in Network Analysis by Shimroz123
1 answer 12 views

The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to: A. 27.2 mA B. 59 mA C. 5.9 mA D. 590 mA

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 22 views

A three phase diode bridge rectifier is fed from a 400 V rms, 50 Hz, three phase a.c. source. For the purely resistive load, the peak instantaneous output voltage is 

asked May 25, 2018 in Diode by Shimroz123
1 answer 24 views

In a balanced 3 -phase 200 V circuit, the line current is 115.5 A. When the power is measured by two wattmeter method, one of the wattmeters reads 20 kW and the other one reads zero. What is the power factor of the load ?

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
1 answer 17 views

 If the range of an analog transducer is 0 to 10 V, then for a resolution of 5 mV, the bits of ADC will be _____.

asked May 29, 2018 in Transducers and sensors by Shimroz123
1 answer 51 views

In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 17 views

Approximately how many milliamperes of current flow through a circuit with a 40 V source and 6.8 k ohms of resistance? A.27.2 mA B.59 mA C.5.9 mA D.590 mA

asked May 15, 2018 in Basic concepts by Shimroz123
0 answers 20 views

What is the electron valence of an element with an atomic number of 3?

asked Jul 1 by Shimroz123
1 answer 20 views

An emf of 120 V causes a current of 3A to flow in a circuit how much energy is supplied by the source in 12 seconds. A. 4130 J B. 4310 J C. 4320 J D. None of these 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
1 answer 23 views

A 3 layer, total diameter of an ACSR conductor is 5 cm. Find the diameter of each strand?

asked May 8, 2018 in Electric Power Transmission by Shimroz123
1 answer 5 views

As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is A) 25 A B) 50 A C) 100 A D) 200A

asked May 20, 2018 in Network Analysis by Shimroz123
1 answer 10 views

Consider the following statements : Any element connected in  1. Series with an ideal current source is redundant. 2. Parallel with an ideal current source is redundant. 3. Series with an ideal voltage source is redundant. . 4. Parallel with an ideal voltage source is redundant.  Which of the above statements is/are correct ?

asked Apr 23, 2018 in Electrical Engineering by Zeeshan
0 answers 26 views

To Charge a 120 V battery from a 600 V DC source using a DC chopper, The average battery current should be 20 A, with a peak to peak ripple of 2 A. If the chopper frequency is 200 Hz, calculate the duty cycle.  (A) 0.2 (B) 0.1 (C) 0.5 (D) 0.6 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 546 views

The turns ratio required to match an 80 ohms source to a 320 ohms load is? A.80 B.20 C.4 D.2

asked May 15, 2018 in Basic concepts by Zeeshan
1 answer 19 views
1 answer 56 views

What is the resistance of a coil which draws 10 A and dissipates 1520 W? A) 152 Ω B) 15.2 Ω C) 1.52 Ω D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

Output of an op-amp is a square wave of 4 V peak to peak with a rise time of 5 microsecond and fall time of 4 microsecond.Maximum frequency (in kHz)of undistorted sine wave output of 2 V peak to peak is about  A) 100 B) 150 C) 200 D) 250

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 25 views

A Transformer rated 250 kVA, 4160 V / 480 V, 60 Hz has an impedance of 5.1%. Calculate the total impedance of the transformer referred to the primary side.  (A) 69 ohm (B) 0.92 ohm (C) 3.52 ohm (D) 0.51 ohm

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
2 answers 58 views

The synchronous speed of an 8 pole induction motor supplied power from a 50 Hz source will be ?

asked Dec 31, 2017 in Electrical Engineering by Quiz
0 answers 21 views

A ramp voltage V(t)=100 V is applied to an RC differentiating circuit with R=5 kΩ and C=4 μF. The maximum output voltage is  (A) 0.2 V (B) 2 V (C) 10 V (D) 50 V

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

To find current in a resistance connected in a network, Thevenin's theorem is used VTH = 20 V and RTH = 5 Ω. The current through the resistance: (1) is 4 A (2) is 4 A or less (3) is less than 4 A (4) May be 4 A or less or more than 4 A

asked May 29, 2018 in Network Analysis by Shimroz123
1 answer 14 views

The filament of an electric bulb is made of?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 10 views

You are measuring the current in a circuit that is operated on an 18 V battery. The ammeter reads 40 mA. Later you notice the current has dropped to 20 mA. How much has the voltage changed? A.9 V B.900 mV C.0 V D.18 V

asked May 15, 2018 in Basic concepts by Shimroz123
1 answer 24 views

The energy used by a 1.5kW heater in 5 minutes is:

asked May 22, 2018 in Electrical Engineering by Shimroz123
1 answer 33 views

A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be

asked May 8, 2018 in Electrical Machine by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...