12 views
in Electronics communication by
For an antenna to be frequency-independent, it should expand or contract in proportion to the 

(a) gain (b) directivity (c) wavelength (d) impedance

1 Answer

0 votes
by

For an antenna to be frequency-independent, it should expand or contract in proportion to the impedance

Related questions

1 answer 33 views

An antenna located in a city is a source of radio waves. How much time does it take the wave to reach a town 12,000 km away from the city?  a. 36 s b. 20 us c. 20 ms d. 40 ms 

asked May 17, 2018 in Telecommunication Engineering by anonymous
1 answer 12 views

Earth coverage dish antenna is used in satellite system. It is characterized by the fact that  (a) It is a narrow beam antenna (b) It is Parabolic antenna (c) it is sharply focused within a small area of the surface of the earth (d) it is a wide angle antenna which covers a large area of the surface of the earth

asked May 15, 2018 in Electronics communication by Shimroz123
1 answer 22 views

In a radio transmitter, the frequency of the crystal oscillator will be stable for a long time if the quality factor of the crystal resonator is  (a) > 100 (b) > 500 (c) > 1000 (d) > 20000

asked May 15, 2018 in Electronics communication by Shimroz123
1 answer 16 views

When an antenna of input resistance 73 ohm is connected to a 50-ohm line and if the losses are ignored then its efficiency will be nearly   (A) 0.19 (B) 0.81 (C) 0.97 (D) 1.19

asked May 17, 2018 in Electronics communication by Shimroz123
1 answer 60 views

To read or write a complete word from / to the memory in 8086 microprocessor and if it is located at an even address, the number of Read or Write cycles required is

asked May 23, 2018 in Microprocessors and Microcontrollers by Shimroz123
0 answers 17 views

In an axial mode operation of a helical antenna, maximum field radiated by the antenna is :  A) along the axis of the helical B) in a plane normal to the helix antenna axis C) in both axial and normal planes D) None of the above

asked Apr 9, 2018 in Electronics communication by Shimroz123
1 answer 85 views

The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

asked Jun 18, 2018 in Microprocessors and Microcontrollers by Shimroz123
1 answer 18 views

Two transformers are to be operated in parallel such that they share load in proportion to their kVA ratings. The rating of the first transformer is 500 kVA ratings. The rating of the first transformer is 500 kVA and its pu leakage impedance is 0.05 pu. If the rating of second transformer is 250 kVA, its pu leakage impedance is  (A) 0.20 (B) 0.10 (C) 0.05 (D) 0.025

asked May 17, 2018 in Transformer by Shimroz123
1 answer 11 views

When a dipole antenna of 1/8 length has an equivalent total resistance of 1.5 Watt then the efficiency of the antenna is   (A) 0.89159% (B) 8.9159% (C) 89.159% (D) 891.59%

asked May 17, 2018 in Electronics communication by Shimroz123
1 answer 34 views

For a traction transformer circuit breaker state: 1) Rated current and rupturing capacity 2) Any two tests it should be capable of withstanding 3) Overall tripping time and relay time.

asked Sep 2, 2018 by Shimroz123
1 answer 9 views

The Ku frequency band used in satellite communication (for uplink and downlink) is: (1) 14 GHz and 11 GHz (2) 30 GHz and 20 GHz (3) 70 GHz and 50 GHz (4) 60 GHz and 45 GHz 

asked May 29, 2018 in Electronics communication by Shimroz123
0 answers 58 views

To enable dc series motor work satisfactory with an AC supply, the following modifications should be done (1) The yoke and poles should be completely laminated (2) The poles should be made of laminated steel (3) The air gap between stator and rotor be reduced (4) Compensating poles should be introduced  

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

500 Bytes of data needs to be transmitted from an UART every lOOms. What should be the minimum transmission baud rate of UART, assuming 1 start bit, 8 data bits and 2 stop bits?  A) 50000 B) 55000 C) 40000 D) 45000

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 25 views

A sine wave voltage is applied across an inductor. When the frequency of the voltage is decreased, the current decreases.

asked Nov 23, 2017 in Electrical Engineering by James
1 answer 71 views

 An independent voltage source in series with an impedance ZS=R+jXS delivers a maximum average power to a load impedance ZL when A) ZL = R B) ZL = jXS C) ZL = R-jXS D) ZL = R+jXS 

asked Jun 18, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

For an insulating material, dielectric strength and dielectric loss should be respectively   (A) high and high (B) low and high (C) high and low (D) low and low.

asked May 16, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

Which of the following is an inherent property of an optical signal and cannot be eliminated even in principle? (1) Thermal noise (2) Shot noise (3) Environmental noise (4) Background Noise

asked May 29, 2018 in Electronics communication by Shimroz123
1 answer 16 views

When two transformer of different kVA rating are connected in parallel they share the load in proportion to their respective kVA rating only when their:

asked May 22, 2018 in Transformer by Shimroz123
0 answers 38 views

Ideally Voltage Standing Wave Ratio (VSWR) should be  (a) as large as possible (b) as small as possible (c) as close to unity as possible (d) infinity

asked Apr 9, 2018 in Electronics communication by Shimroz123
1 answer 5 views

Radio frequency ranges from 30MHz to 1GHz and it is suitable for:  a. Point to point transmission b. Omni directional transmission c. Local point to point transmission d. None of the above

asked May 17, 2018 in Telecommunication Engineering by anonymous
1 answer 29 views

The burden value in Potential Transformer (PT) should be ______ to achieve low errors in PT: A) low B) high C) medium D) infinite

asked Jun 17, 2018 in Switchgear And Protection by Shimroz123
1 answer 12 views

Find the noise factor for an antenna at 27°C with equivalent noise temperature 30°K: (1) 20 (2) 100 (3) 300 (4) 1.1 

asked May 28, 2018 in Analog electronics circuits by Shimroz123
0 answers 17 views

For measuring the frequency of an unknown A.C. source. Which of the following device is necessary to obtain a standard waveform?  (A) Operational amplifier (B) Astable multivibrator (C) Schmitt trigger (D) Monostable multivibrator

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

_________allows to execute the methods of an object in another machine or JVM?  A) Protocol handler B) Streaming C) RMI D) IPC

asked Apr 11, 2018 in Computer Engineering by Shimroz123
1 answer 20 views

In d.c. choppers, for periodic time T, the output voltage can be controlled by frequency modulation by varying

asked May 20, 2018 in Power Electronic Controlled Drives by Shimroz123
0 answers 16 views

An alternator with frequency f1 is to be synchronized with an infinite bus of frequency f. For proper synchronization (1) f1=f (2) f1<f (3)f1>f (4) either (b) or (c) 

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 33 views

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
0 answers 41 views

The signal is extended from 96KHz to 100KHz, so the minimum sampling frequency required is  (a) 8KHz (b) 200KHz (c) 4KHz (d) 100KHz

asked Apr 9, 2018 in Electronics communication by Shimroz123
1 answer 24 views

The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is  (A) The active device itself (tube, or transistor)  (B) stray shunt capacitance Cs  (C) the grid leak resistance Rg  (D) coupling capacitor Cc

asked May 12, 2018 in Amplifier by Shimroz123
1 answer 24 views

Which of the following heating methods is independent of supply frequency?  (A) electric are beating (C) electric resistance heating (B) induction heating (D) dielectric heating

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

If the antenna diameter in a radar system is increased by a factor of 4, the maximum range will be increased by a factor of  (a) 2 (b) 4 (c) 8 (d) 16

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
2 answers 33 views

If an atom loses one or more electrons, it becomes _____.

asked May 29, 2018 in Physics by Shimroz123
1 answer 33 views

 The insulation resistance of earth of an installation should be nearly: -  a) 0.1 M ohm b) 0.2 M ohm c) 0.5 M ohm d) 1 M ohm.

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
0 answers 40 views

If an energy meter disc makes 10 revolutions in 100 seconds when a load of 450W is connected to it, the meter constant in revolutions per kWh is  A) 1000 B) 500 C) 1600 D) 800

asked Apr 9, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...