Can you help by answering this question?

What is wiring?

14 views
in Amplifier by
In a Klystron amplifier, the RF voltage produces 

(a) amplitude modulation (b) frequency modulation (c) phase modulation (d) velocity modulation

1 Answer

0 votes
by

In a Klystron amplifier, the RF voltage produces velocity modulation

Related questions

1 answer 11 views

In a klystron amplifier the input cavity is called:  (1) Buncher (2) Catcher (3) Pierce gun (4) Collector

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 23 views

The voltage gain of a common base amplifier depends on  1. Load resistor RL 2. input resistance of transistor 3. Ac alpha 4. All the above 

asked May 13, 2018 in Amplifier by Shimroz123
1 answer 25 views

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

asked May 29, 2018 in Amplifier by Shimroz123
1 answer 10 views

Just as a voltage amplifier signal voltage a power amplifier.  1.amplifier power  2.amplifier signal  3.converts the signal ac power into DC power  4.converts a dc power into useful AC power 

asked May 13, 2018 in Amplifier by Shimroz123
0 answers 21 views

The RF amplifier A is having 3 dB NF & 5 dB of gain, amplifier B is having 3.5 dB NF & 15 dB . For overall noise figure of the cascaded system, the correct statement is :  a. A as first stage & B as second stage offers minimum over all NF b. B as first stage & A as second stage minimum over all NF c. Both the combination will offer same overall NF d. Over all NF will be less than 3 dB.

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
0 answers 14 views

If the emitter resistance ‘Re ’ in a transistor amplifier is removed, then (a) base to emitter junction will be less forward biased. (b) gain of amplifier decreases. (c) Q-point becomes unstable. (d) All of these 

asked May 25, 2018 in Amplifier by Shimroz123
1 answer 14 views

In a radio receiver the IF amplifier  (A) is tuned above the stations incoming frequency (B) amplifies the output of local oscillator (C) is fixed tuned to one particular frequency (D) can be tuned to various isolate frequencies

asked May 17, 2018 in Amplifier by Shimroz123
1 answer 13 views

In class - A power amplifier, the collector dissipation is maximum when  (a) no signal is present  (b) signal swing is maximum  (c) signal swing is (1/1.414) of its maximum  (d) none of the above

asked May 15, 2018 in Amplifier by Shimroz123
1 answer 12 views

In class-A amplifier conduction extends over 360° because the operating point.  1. Located near saturation point 2. Located at or near cut-off point 3. Located on load line 4. Located in the centre of load line 

asked May 13, 2018 in Amplifier by Shimroz123
1 answer 54 views

The main function of the transformer used in the output of a power amplifier is  (A) To step up the voltage  (B) to increase the voltage gain  (C) to safeguard the transistor against overheating  (D) to match the load impedance with dynamic output resistance of the transistor

asked May 12, 2018 in Amplifier by Shimroz123
0 answers 14 views

A high-Q tuned circuit in an amplifier permits to have high (a) selectivity (b) fidelity (c) sensitivity (d) frequency ranges

asked May 25, 2018 in Amplifier by Shimroz123
1 answer 13 views

In an IF amplifier, the IF transformer is provided with tapping to  (a) increase the voltage gain (b) increase the bandwidth of the resonance circuit (c) increase the impedance offered by the resonance circuit to the following cascaded amplifier (d) increase the quality factor of the resonance circuit 

asked May 15, 2018 in Amplifier by Shimroz123
1 answer 23 views

In Class ‘B’ amplifier, the output current flows for

asked May 15, 2018 in Amplifier by Shimroz123
1 answer 9 views

Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is  (A) The transistor itself  (B) the power supply Vcc  (C) the coupling capacitor Cc  (D) the biasing resistors

asked May 12, 2018 in Amplifier by Shimroz123
1 answer 24 views

The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is  (A) The active device itself (tube, or transistor)  (B) stray shunt capacitance Cs  (C) the grid leak resistance Rg  (D) coupling capacitor Cc

asked May 12, 2018 in Amplifier by Shimroz123
1 answer 15 views

What is the importance of negative feedback in the operational amplifier? (A) It maintains the gain (B) The voltage difference between the input terminals is maintained at a very small value (C) The voltage difference between the input terminals is maintained at a constant value (D) The voltage difference between the input terminals is maintained at a very high value

asked May 12, 2018 in Amplifier by Shimroz123
1 answer 27 views

A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 20 views

For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 28 views

An amplifier without feedback has a gain of 1000. The gain with a negative feedback of 0.009 is  A) 10 B) 100 C) 125 D) 900

asked May 20, 2018 in Amplifier by Shimroz123
1 answer 14 views

Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will   (A) Amplify the noise as much as the signal (B) Reduce the noise (C) Increase the noise (D) Not effect the noise

asked May 17, 2018 in Amplifier by Shimroz123
1 answer 11 views

The efficiency of a class B push-pull amplifier is

asked May 14, 2018 in Amplifier by Shimroz123
1 answer 8 views

The battery operated pre-amplifier with a consumption of 10 Watts can work on battery of 12 volt, 100 AH having efficiency of 50% for • 120 hrs. • 60 hrs. • 100 hrs. • 10 hrs.

asked May 14, 2018 in Amplifier by Shimroz123
1 answer 33 views

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

asked Jun 18, 2018 in Electronics Engineering by Shimroz123
1 answer 23 views

Which of the following cells produces a highly stable voltage? A) Weston cell B) Leclanche cell C) Both A and B D) None of these

asked Apr 29, 2018 in Electrical Engineering by Shimroz123
1 answer 17 views

Negative feedback in an amplifier is accompanied by (A) Gain less sensitive to component variations (B) Increase in gain (C) Decrease in bandwidth (D) None of the above

asked May 12, 2018 in Amplifier by Shimroz123
1 answer 11 views
1 answer 46 views

In a differential amplifier the differential voltage gain is 500 and the common mode voltage gain is 0.5. The CMRR in dB is (a) 80 (b) 60 (c) 30 (d) 20

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 30 views
1 answer 13 views

Class A amplifier is used when  (A) No phase inversion is required (B) Highest voltage gain is required (C) dc voltages are to be amplified (D) Minimum distortion is desired. 

asked May 17, 2018 in Amplifier by Shimroz123
1 answer 19 views

The ac bypassing of RF by CF in a common emitter configuration :  (A) increases ac signal across emitter -base junction (B) decreases ac signal across emitter -base junction (C) decreases voltage amplification (D) stabilizes the Q -point

asked Apr 30, 2018 in Electrical Engineering by Shimroz123
0 answers 41 views

In a Traveling-wave Tube, the velocity of electron beam with respect to the axial velocity of RF field is kept...  A) Lower B) Higher C) Equal D) Any of these

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 30 views
1 answer 26 views

The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

asked Jun 18, 2018 in Amplifier by Shimroz123
1 answer 12 views

The ideal operational amplifier does not have: (1) Infinite input resistance (2) Infinite output resistance (3) Infinite voltage gain (4) Infinite bandwidth 

asked May 29, 2018 in Amplifier by Shimroz123
1 answer 14 views

The gain of an FET amplifier can be changed by changing: (1) rm (2) gm (3) Rd (4) None of these

asked May 28, 2018 in Amplifier by Shimroz123
0 answers 10 views

The amplifier having the highest amount of distortion is (a) Class A (b) Class B (c) Class C (d) Class AB 

asked May 25, 2018 in Amplifier by Shimroz123
1 answer 34 views

If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is (a) – 13.3 (b) 200 (c) 8 (d) 10 

asked May 25, 2018 in Amplifier by Shimroz123
1 answer 15 views

An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 12 views

For Cascode amplifier the output impedance becomes 

asked May 23, 2018 in Amplifier by Shimroz123
1 answer 17 views

Which of the following amplifier has the least distortion. • Class E • Class D • Class C • Class A

asked May 14, 2018 in Amplifier by Shimroz123
1 answer 9 views

Voltage applied across a ceramic dielectric produces an electrostatic field 100 times greater than in air. The dielectric constant? of the ceramic equals________. 

asked Mar 31, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

An amplifier has a voltage gain of 50; this gain in dB will be (A) 34 dB (B) 68 dB (C) 41 dB (D) 14 dB 

asked Apr 23, 2018 in Instrumentation and control by Shimroz123
1 answer 29 views

Switching of a lamp in house produces noise in the radio. This is because switching operation produces?

asked Mar 25, 2018 in Basic concepts by Shimroz123
0 answers 7 views

Push-pull amplifier circuit is used as (a) RF amplifier (b) audio amplifier (c) power amplifier (d) current amplifier

asked May 25, 2018 in Amplifier by Shimroz123
1 answer 11 views

An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

asked May 20, 2018 in Amplifier by Shimroz123
0 answers 10 views

In digital modulation, if the phase in the received RF pulse is unknown (a) coherent detection can be used (b) coherent detection cannot be used (c) envelope detection cannot be used (d) non coherent techniques cannot be used

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 26 views

If the RF transmission is terminated in its Characteristic impedance Z, which of the following statements is wrong : a. The input impedance of transmission line becomes Zc. b. The transmission line acts as an infinite long transmission line. c. The VSWR becomes one d. The VSWR becomes infinite

asked Apr 12, 2018 in Electronics Engineering by Shimroz123
1 answer 11 views

An Op-amp as a voltage follower has a voltage gain of

asked May 14, 2018 in Amplifier by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...