# In order to generate electron-hole pairs, the maximum wavelength of radiation for Silicon (Band gap = 1.1 eV)

18 views
in Physics
In order to generate electron-hole pairs, the maximum wavelength of radiation for Silicon (Band gap = 1.1 eV) is

(a) 1.88 μm (b) 1.68 μm (c) 1.13 μm (d) 1.54 μm

In order to generate electron-hole pairs, the maximum wavelength of radiation for Silicon (Band gap = 1.1 eV) is 1.13 μm

## Related questions

The band gap of elements arranged in ascending order is : a. Diamond, Ge, Si b. Si, Ge, Diamond c. Ge, Si, Diamond d. Diamond, Si, Ge

Which of the following is true regarding the band-gap energy of a semiconductor ? (A) Minimum energy required to break a covalent bond (B) On breaking of the bond, electron is generated (C) On breaking of the bond, electron-hole pair is generated (D) A & C both are true

If temperature of a radiating body is 1500 °C, the wavelength at which maximum radiant energy occurs is (a) 2.87 µm (b) 1.63 µm (c) 1.01 µm (d) 20.85 µm

For identical total transmitted power, the ratio of S/N for wide band FM to S/N of DSB-AM (with ma=1) is : ( Given fm = 15 KHz & frequency. deviation =+/- 75 KHz) a. 112.5 b. 300 c. 75 d. 450

An electron having an energy of 20 eV enters a magnetic field of 0.02 webers/sqm at an angle of 30degrees to the field. The time of travel (in nS)of the electron for one revolution is about  A) 1.78 B) 4.21 C) 7.82 D) 10.24

In any atom the potential energy of an orbiting electron is   (A) always positive (B) always negative (C) sometime positive, sometime negative (D) numerically less then its kinetic energy.

An electron in the conduction band has (A) More energy than the electron in the valence band (B) Lesser energy than the electron in the valence band (C) Same energy as that of the electron in the valence band (D) No energy at all

Impurity atoms to be added to pure silicon in order to make a p-type semiconductor belongs to (a) Phosphorous (b) Boron (c) Antimony (d) Aluminium

A half wavelength Dipole antenna has _________ Radiation Pattern  a. Hemispherical b. Omni-Directional c. Isotropic d. End fire

Orbital magnetic moment of an electron, in an atom, is of the order of (a) 0.1 Bohr magneton (b) 1.0 Bohr magneton (c) 10 Bohr magneton (d) 100 Bohr magneton

In the selenium cell photovoltaic transducer, relative spectral sensitivity maximum occurs in the wavelength (in nm) of about  A) 300 B) 350 C) 460 D) 550

The charge on an electron is known to be 1.6 x 10-19 coulomb. In a circuit the current flowing is 1 A. How many electrons will be flowing through the circuit in a second?

The transferred electron bulk effect occurs in

In order to get maximum power transfer from a capacitive source, the load must? A.have a capacitive reactance equal to circuit resistance B.have an impedance that is the complex conjugate of the source impedance C.be as capacitive as it is inductive D.none of the above

To generate 1 MHz signal, the most suitable circuit is (a) Wein bridge oscillator (b) Phase shift oscillator (c) Colpitts oscillator (d) None of these

The Maximum spectral response of the germanium and silicon is in the   (A) infrared region (B) ultraviolet region (C) visible region (D) x-ray region

What is the charge and mass of an electron?

A silicon p-n junction at a temperature of 20 °C has a reverse saturation current of 10 pA. The reverse saturation current at 40 °C will approximately be (a) 30 pA (b) 40 pA (c) 50 pA (d) 60 pA

Define conduction band & forbidden energy gap.

Semiconductor A has a higher band gap than semiconductor B. If both A and B have the same dimensions, the same number of electrons at a given temperature and the same electron and hole mobilities, then

If temperature of a pure silicon specimen is increased, then (a) only number of free electrons increase. (b) only number of free holes increase. (c) number of free holes and free electrons increases. (d) only number of free holes decrease.

The correct order of electromagnetic spectrum with decreasing frequency is: (1) Microwaves, Radiowaves, Infrared rays, Ultraviolet rays, X–rays (2) Radiowaves, Infrared rays, Ultraviolet rays, Microwaves, X–rays (3) X–rays, Infrared rays, Microwaves, Radiowaves, Ultraviolet rays (4) X–rays, Ultraviolet rays, Infrared rays, Microwaves, Radiowaves

For a 2nd order feedback control system, the peak resonance magnitude should be Mp ≤ 1.15. Hence the damping ratio (δ) is  (a) 0.1 (d) 0.5 (c) 0.707 (d) 1

The effect of increasing the length of air gap in an induction motor is to increase the (a) power factor (b) speed (c) magnetising current (d) air gap flux

In order to switch-off and EHV circuit for maintenance, the following sequence is adopted: (1) Open the circuit breaker, open the isolator, operate the earth switch (2) Operate the earth switch, open the isolator, open the circuit breaker (3) Open the isolator, operate the earth switch, open the circuit breaker (4) Open the isolator, open the circuit breaker, operate the earth switch

In order to recover the original signal from the Sampled one, what is the condition to be satisfied for sampling frequency ωs and highest frequency component ωm?  (A) ωm < ωs ≤ 2 ωm (B) ωs ≥ 2 ωm (C) ωs < ωm (D) ωs = ωm

Propagation medium of the signal in band (3 to 30) MHz is by  A) Space wave B) Surface wave C) Sky wave D) LOS

Silicon dioxide is (A) a conductor (B) an insulator (C) a useful circuit element  (D) useful as contact in MOSFET

In a Traveling-wave Tube, the velocity of electron beam with respect to the axial velocity of RF field is kept...  A) Lower B) Higher C) Equal D) Any of these

Velocity of an electron (in km/S) starting at rest and travelling to a point 100 V above the starting potential is around  A) 3600 B) 4000 C) 5100 D) 6000

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

Which of the following is false for switch statement in C++?  (1) It uses labels instead of blocks (2) we need to put break statement at the end of the group of statement of a condition (3) we can put range for case such as case 1..3 (4) None of these

The Ku frequency band used in satellite communication (for uplink and downlink) is: (1) 14 GHz and 11 GHz (2) 30 GHz and 20 GHz (3) 70 GHz and 50 GHz (4) 60 GHz and 45 GHz

A 200 V dc motor takes a field current of 2 A to generate a back emf of 180 V. If the field winding resistance is 80 Ω, the resistance of the shunt field regulator is (A) 10 Ω (B) 20 Ω (C) 100 Ω (D) 180 Ω

A pair of synchronous machines on the same shaft may be used to generate power at 60 Hz from given source of power at 50 Hz. Using minimum number of poles for both the machines, the synchronous speed will be (a) 500 r.p.m. (b) 600 r.p.m. (c) 1000 r.p.m. (d) 1200 r.p.m.

The amount of solar radiation received on a unit area exposed perpendicular to sunlight is termed as : (A) Solar insulation (B) Solar constant (C) Solar radiance (D) Solar insolation

To measure insulation resistance of equipments of voltage rating upto 440 V the megger generator must generate   (a) 220 V (b) 440 V (c) 500 V (d) None of these

In the order of priority of hardware interrupts of 8085A, 3rd priority (in descending order) is for  A) Trap B) INTR C) RST6.5 D) RST5.5

To increase mobility of electron in a given piece of semiconductor (A) Increase overall size of the semiconductor (B) Increase length (C) Increase width (D) Small increase in temperature above room temperature value

What happens to the reluctance of a magnetic circuit, when an air gap is introduced to the core cross section ? (A) Decreases (B) Increases (C) Remain same (D) None of the above

A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of  A) 0.8 ohm in series with the meter B) 1.0 ohm in series with the meter C) 0.04 ohm in parallel with the meter D) 0.05 ohm in parallel with the meter

In order to increase the range of a voltmeter