# A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and

20 views
A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and armature resistance are 100 volt and 0.5Ω respectively. With the magnitude control ratio 0.6, the quadrant of operation DC motor is

(a) First (b) Second (c) Third (d) Fourth

A step-down chopper, fed from a 120 volt DC source, operates a DC motor whose armature e.m.f. and armature resistance are 100 volt and 0.5Ω respectively. With the magnitude control ratio 0.6, the quadrant of operation DC motor is First

## Related questions

0 answers 26 views

To Charge a 120 V battery from a 600 V DC source using a DC chopper, The average battery current should be 20 A, with a peak to peak ripple of 2 A. If the chopper frequency is 200 Hz, calculate the duty cycle.  (A) 0.2 (B) 0.1 (C) 0.5 (D) 0.6

0 answers 20 views

The duty ratio of a step-up chopper with an output voltage of 200 V from a 80 V dc source, is (A) 0.4 (B) 0.5 (C ) 0.6 (D) 1.5

1 answer 22 views

Which of the following quantity maintains the same direction whether a D.C. machine runs as a generator or as a motor a. Induced e.m.f. b. Armature Current c. Field Current d. Supply Current

1 answer 15 views

The induced e.m.f. in the armature conductors of a d.c. motor is?

1 answer 28 views
0 answers 421 views

A shunt motor rotating at 1500 r/min is fed by a 120 V source. The line current is 51 A and the shunt field resistance is 120 ohm. If the armature resistance is 0.1 ohm, calculate the current in the armature.  (A) 1 A (B) 51 A (C) 50 A (D) 12 A

1 answer 39 views

A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while the chopper feeds an RL load. The per unit current ripple would  (1) increase progressively  (2) decrease progressively  (3) decrease to a minimum value at α = 0.5 and then increase  (4) increase to a maximum value at α = 0.5 and then decrease

1 answer 21 views
1 answer 15 views

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

2 answers 31 views

A network which contains one or more than one source of e.m.f. is known as?

1 answer 25 views

A DC chopper is used for regenerative braking of a separately excited DC motor. The DC supply voltage is 400V. The armature current during regenerative braking is kept constant at 300 A with negligible ripple. For a duty cycle of 60% the power return to the DC supply is  (a) 78 kW (b) 58 kW (c) 38 kW (d) 48 kW

1 answer 56 views

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) inversely proportional to α and Φ (C) directly proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

2 answers 21 views

Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to:  (1) 1 (2) 0.5 (3) 0.75 (4) 0.33

5 answers 27 views

If a d.c. motor is disconnected from the source and armature circuit is short circuited through a suitable resistance, the process is called (a) regenerative breaking (b) rheostatic breaking (c) dynamic breaking (d) no breaking is possible

1 answer 35 views

Chopper controlled DC motor

1 answer 48 views

In a Synchronous motor, the magnitude of stator back e.m.f (Eb) depends on

1 answer 8 views

The back e.m.f of a motor at the moment of starting : -  a) zero b) maximum c) minimum d) optimum

1 answer 15 views

The counter e.m.f. of a d.c. motor?

1 answer 26 views
1 answer 18 views

As there is no back e.m.f. at the instant of starting a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit?

1 answer 29 views
1 answer 178 views
1 answer 7 views

A single-phase, 230 V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ohm. The charging current is  (A) 2.43 A (B) 1.65 A (C) 1.22 A (D) 1.0 A

0 answers 19 views

A separately excited d.c. motor fed from single phase full converter with firing angle 60° runs at 1000 r.p.m. If motor is connected to single phase semiconverter with the same firing angle of 60°, it would run at (a) 2000 rpm (b) 1850 rpm (c) 1500 rpm (d) 1000 rpm

2 answers 26 views

Three lamps are connected in parallel across a 120 Volt source. If one lamp burns out, the remaining two will be: A. Glow dimmer B. Glow brighter C. Not light D. Glow with the same brightness as before

1 answer 16 views

A separately excited dc motor operating in first quadrant is fed from 3-phase semi -converter free -wheeling diode is open circuited, then the motor :  (A) can be operated in first quadrant (B) can be operated in first & second quadrants (C) can be operated in first & fourth quadrants (D) cannot be operated

1 answer 18 views

A 3-phase fully controlled bridge converter with free wheeling diode is fed from 400 V, 50 Hz AC source and is operating at a firing angle of 60o. The load current is assumed constant at 10 A due to high load inductance. The input displacement factor (IDF) and the input power factor (IPF) of the converter will be  (A) IDF IPF = = 0.867; 0.828 (B) IDF IPF = = 0.867; 0.552 (C) IDF IPF = = 0.5; 0.478 (D) IDF IPF = = 0.5; 0.318

0 answers 21 views

A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A

1 answer 10 views

Which law states that induced e.m.f and current always opposes the cause producing them?

1 answer 23 views

Five cells, each with an e.m.f. of 2V and internal resistance of 0.5Ω are connected in series. The resulting battery will have

0 answers 16 views

The voltage regulation of an alternator having 0.75 leading p.f. load, no-load induced e.m.f. of 2400V and rated terminal voltage of 3000V is —————————————  A) 20% B) —20% C) 150 D) -26.7

1 answer 29 views
1 answer 23 views
1 answer 21 views
1 answer 593 views

In a step-up or step-down transformer, electrical power is transferred from one circuit to another without change in

1 answer 22 views

The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be  (A) 48.0% (B) 57.1% (C) 59.2% (D) 88.8%

1 answer 6 views

Define the following terms as referred to battery. a) E.M.F b) Internal resistance c) Ah efficiency d) WAh efficiency

1 answer 6 views

These self inductance of a circuit is defined as twice the work done against the induced e.m.f. on establishing unit current in the coil. If the current to be established in the coil is doubled, the work done against the induced e.m.f. will be  1. Doubled  2. Halved  3. four times  4. Quarter times

0 answers 35 views
1 answer 18 views

The e.m.f. induced in the primary of a transformer:  (A) is in phase with the flux (B) lags behind the flux by 90 degree (C) leads the flux by 90 degree (D) is in phase opposition to that of flux

1 answer 20 views
1 answer 23 views
1 answer 23 views
1 answer 19 views
1 answer 55 views

A shunt generator running at 1000 r.p.m. has generated e.m.f. as 200 V. If the speed increases to 1200 r.p.m., the generated e.m.f. will be nearly?

1 answer 13 views
1 answer 54 views
1 answer 19 views
1 answer 33 views

A large dc motor is required to control the speed of the blower from a 3 -phase ac source. The suitable ac to dc converter is, 3 -phase (a) Fully controlled bridge converter (b) Fully controlled bridge converter with freewheeling diode (c) Half controlled bridge converter (d) Converter pair in sequence control

1 answer 23 views

If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be?