17 views
in Digital Instrumentation by
Transient signals can be observed using 

(a) storage oscilloscope (b) sampling oscilloscope (c) wave analyzer (d) spectrum analyzer

Your answer

Thanks for your contribution. Feel free to answer this question. Please avoid short answer. Your answer is most welcome. Be genuine.

Upload image or document:

Your name to display (optional):
Privacy: Your email address will only be used for sending these notifications.
Anti-spam verification:
Are you a robot ? (Y = Yes / N = No)
To avoid this verification in future, please log in or register.

1 Answer

0 votes
by

Transient signals can be observed using storage oscilloscope

Related questions

0 answers 13 views

Transient stability can be improved by using governors attached to the turbines, should be (a) fast acting (b) slow acting (c) no function of governors in improving stability (d) nothing can be said  

asked May 25, 2018 in Power system by Shimroz123
1 answer 10 views

Two sinusoidal signals of the same frequency are displayed on a dual-trace oscilloscope. One complete cycle of each signal covers 6 cm of the horizontal scale and the starting point of the horizontal scale and the starting point of the two signals are separated by 0.5 cm. The phase difference between the two signals in degrees is  (a) 30 (b) 45 (c) 60 (d) 90

asked May 15, 2018 in Digital Instrumentation by Shimroz123
1 answer 7 views

To distinguish between signals having very close values, we need an instrument with  (a) high accuracy (b) high resolution (c) high sensitivity (d) high linearity

asked May 15, 2018 in Digital Instrumentation by Shimroz123
0 answers 14 views

A bi-stable multi-vibrator can be built by using (A) NAND gates (B) AND gates (C) AND or OR gates (D) Excusive-NOR gates 

asked Jun 4, 2018 in Digital Electronics by Shimroz123
1 answer 14 views

Turn on time of an SCR can be reduced by using a:

asked May 22, 2018 in Power Electronics by Shimroz123
1 answer 11 views

The measurement range of an ammeter can be increased by using a:

asked May 22, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 14 views

Thyristor can be protected from over voltages by using

asked May 8, 2018 in Power Electronics by Shimroz123
1 answer 18 views

The self inductance of a coil can be measured using (A) Wien’s Bridge (B) Schering Bridge (C) Anderson’s Bridge (D) Wheatstone Bridge

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
1 answer 18 views

A 1ms pulse can be stretched to 1 s pulse by using (A) an astable multivibrator (B) a monostable multivibrator (C) a bistable multivibrator (D) a Schmitt trigger circuit

asked Apr 26, 2018 in Electronics Engineering by Shimroz123
0 answers 6 views

The fast Fourier transform (FFT) analysis can be measured using (a) distortion meter (c) power meter (b) spectrum analyser (d) data acquisition system

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 10 views

A keyword can be used as an identifier by using the  A) prefix # B) prefix @ C) prefix $ D) prefix x

asked Apr 11, 2018 in Computer Engineering by Shimroz123
0 answers 17 views

Which of the following permutation can be obtained in the output (in the same order) using a stack assuming that the input is the sequence 1, 2, 3, 4, 5 in that order?  (1) 3, 4, 5, 1, 2 (2) 3, 4, 5, 2, 1 (3) 1, 5, 2, 3, 4 (4) 5, 4, 3, 1, 2 

asked Apr 10, 2018 in Computer Engineering by Shimroz123
0 answers 22 views

What is the maximum data rate that can be transmitted using a QPSK modulation with a roll-off factor of 0.2 for a 36 MHZ transponder?  A) 7.2 Mbps B) 30 Mbps C) 43.2 Mbps D) 60 Mbps

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 12 views

Intensity of Light can be measured using  A) Anemometer B) IR Thermometer C) Clamp on Meter D) Lux Meter

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
0 answers 17 views

A 1 ms pulse can be converted into a 10 ms pulse by using  A) An astable mutivibrator B) A monostable multivibrator C) Bistable multivibrator D) J-K flip flop.

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 17 views

Gauge factor of about 5 can be obtained using strain gauge made of  A) Constantan B) Ferry C) Nichrome V D) Platinum

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 118 views

Improvement of transient stability using SVC

asked Aug 9, 2017 in Flexible AC Transmission System by Zeeshan
1 answer 12 views

Choose the correct statement  (a) Digital multimeters are built using current measuring elements, while analog multimeters are built using voltage measuring units (b) Digital multimeters are built using voltage measuring units, while analog multimeters are built using current measuring units (c) Both digital and analog multimeters are built using voltage measuring units (d) Both digital and analog multimeters are built using current measuring units

asked May 15, 2018 in Digital Instrumentation by Shimroz123
1 answer 22 views

Very small displacements are effectively measured using

asked May 14, 2018 in Digital Instrumentation by Shimroz123
0 answers 43 views

I want to build circuit that produce sweep frequency from 10KHz - 11KHz - 12....... - 20KHz (as maximum) then start again at 10KHz - 11KHz - 12....... - 20KHz looping like this (2-3 seconds per loop) until the power turned off.

asked Aug 13, 2018 in Signals and Systems by nat
1 answer 18 views

Choose the most appropriate statement (A) An antenna can radiate only HF signals (B) An antenna can radiate and receive HF signals (C) An antenna can receive only HF signals (D) An antenna can receive and transmit simultaneously HF signals

asked May 12, 2018 in Electrical Engineering by Shimroz123
0 answers 10 views

In CRO, Lissajous pattern will be a straight line, if the two signals are of same frequency with a phase difference of (a) 0° (b) 180° (c) 360° (d) All of these 

asked May 25, 2018 in Oscilloscope by Shimroz123
0 answers 13 views

For a desirable transient response of a second order system, the damping ratio must be between (a) 0.4 and 0.8 (b) 0.8 and 1.0 (c) 0.3 and 0.5 (d) 0.2 and 0.4

asked May 25, 2018 in Control System by Shimroz123
1 answer 29 views

The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating anode voltage is reduced to half of its previous value. Then, the vertical deflection of the beam on the screen would become (A) 64 mm (B) 32 mm (C) 8 mm (D) 1 mm

asked Apr 28, 2018 in Digital Instrumentation by Shimroz123
1 answer 21 views

If the displayed system time and date is wrong, you can reset it using :  (A) Task bar (B) Menu bar (C) Desk top (D) Control panel

asked May 8, 2018 in Computer Engineering by Shimroz123
1 answer 10 views

Electric ovens using heating elements made of _________can produce a temperature up to 3000°C. (A) nickel (B) graphite (C) chromium (D) iron

asked Apr 11, 2018 in Computer Engineering by Shimroz123
0 answers 69 views

You can copy cell formats from one cell to another by using the  (1) Backspace key (2) Default font (3) Format painter (4) Formatting toolbar 

asked Apr 11, 2018 in Computer Engineering by Shimroz123
0 answers 22 views

How can we improve power factor using synchronous motor?

asked Mar 15, 2018 in Electrical Machine by Quiz
1 answer 26 views

When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially short circuited because  (A) Cables have a low value of capacitance which draws a high value of charging current (B) Cables have a low value of initial resistance (C) Cables have a high value of capacitance which draws a high value of charging current (D) Cables have a low value of capacitance and initial resistance

asked Apr 28, 2018 in Electrical Measurements and Instrumentation by Shimroz123
0 answers 7 views

Using a quarter wave transformer of characteristic impedance 1 Ohm, a load impedance of 100 Ohm will be transformed to an input impedance of value :  A) 1 Ohm B) 100 Ohm C) 0.01 D) 0.1 Ohm

asked Apr 9, 2018 in Electrical Engineering by Shimroz123
1 answer 49 views

A 200 V, 10 A motor could be rewound for 100 V, 20 A by using .......... as many turns per coil of wire, having .......... the cross-sectional area.

asked Mar 26, 2018 in DC motor by Shimroz123
1 answer 4 views

Name the effect of electric current observed in electroplating. Explain the same.

asked Jul 5 by Shimroz123
1 answer 24 views

The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X–plate input is 2 sin ωt, the Y–plate input is (1) 2 sin ωt (2) 2 sin (ωt + 45°) (3) 2 sin (ωt – 45°) (4) 22 sin ωt + 45°) 

asked May 29, 2018 in Oscilloscope by Shimroz123
0 answers 49 views

Piezoelectric effect is generally observed in (a) conductors and super conductors (b) conductors and semi conductors (c) insulators (d) insulators and conductors

asked May 25, 2018 in Capacitor by Shimroz123
1 answer 5 views

Superconductivity is observed for?

asked Mar 28, 2018 in Electrical engineering materials by Shimroz123
1 answer 32 views

When electric current passes through a bucket full of water, lot of bubbling is observed. This suggests that the type of supply is?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 22 views

List at least two examples that show how static electricity can be generated.

asked Jun 29 by Shimroz123
2 answers 63 views

Why noise of motor is produced? How it can be reduced?

asked Oct 12, 2018 in Industry Electrical Systems-II by Shimroz123
2 answers 68 views

Explain how technical losses can be reduced by use of energy efficient transformer in Transmission and Distribution system.

asked Oct 3, 2018 in Energy Conservation And Audit by Shimroz123
1 answer 17 views

Explain how rotary motion can be measured

asked Sep 14, 2018 by Shimroz123
1 answer 56 views

Write how energy can be stored or generated in each of following : i) solar cell ii) geothermal energy iii) hydrogen energy in biomass.

asked Sep 8, 2018 by Shimroz123
1 answer 23 views

The instantaneous power in ac circuits can be obtained by taking product of the instantaneous values of 

asked Aug 31, 2018 by Zeeshan

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,483 questions

7,081 answers

134 comments

3,088 users

...