# An analog voltmeter has a sensitivity of 10kΩ/volt. The galvanometer used in constructing the instrument

13 views
An analog voltmeter has a sensitivity of 10kΩ/volt. The galvanometer used in constructing the instrument will produce a full scale deflection when the current passed through it is

(a) 10 mA (b) 20 mA (c) 50 mA (d) 100 μA

An analog voltmeter has a sensitivity of 10kΩ/volt. The galvanometer used in constructing the instrument will produce a full scale deflection when the current passed through it is 100 μA

## Related questions

A dc voltmeter has a sensitivity of 1000 Ohm/V. When it measures half full scale in 100 V range, the current through the voltmeter is

An ac voltmeter using full -wave rectification and having a sinusoidal input has an ac sensitivity equal to  (1) 1.414 times dc sensitivity (2) dc sensitivity (3) 0.9 times dc sensitivity (4) 0.707 times dc sensitivity

A digital voltmeter uses an A/D converter which needs a start pulse, uses an analog comparator and has a relatively fixed conversion time independent of the applied voltage. The A/D converter is : -  a) Successive Approximation Converter .b) Digital Ramp Converter c) Digital Slope Converter d) All the above

In the case of an instrument reading of 8.3 V with a 0 to 150 voltmeter having a guaranteed accuracy of 1% full scale reading, the percentage limiting error is   (A) 1.810% (B) 0.181% (C)12.45% (D) 0.0018%

The sensitivity of a voltmeter using 0-5 mA meter movement is (a) 200 Ω/V (b) 150 Ω/V (c) 100 Ω/V (d) 50 Ω/V

In a weighted-resistor digital-to-analog converter with 8-bit input, if the resistance corresponding to the MSB is 2K, what will be the resistance corresponding to the LSB?  (a) 250 Ω (d) 512 KΩ (c) 256 KΩ (d) 25.5 Ω

The operation of a ramp type Digital Voltmeter is based on the principle of (A) Voltage-to-current conversion. (B) Voltage-to-time conversion. (C) Current-to-time conversion. (D) Current-to-frequency conversion.

The full scale range of PMMC voltmeter is 100 V and its sensitivity is 1000 Ω/V. If the meter reads 50 V, the current through the voltmeter is (A) 0.05 mA (B) 0.5 mA (C) 5 mA (D) 50 mA

A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is (A) 1 Ω (B) 1.001 Ω (C) 0.5 Ω (D) 10 Ω

An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be  (1) unaffected (2) decreased (3) increased (4) either decreased or increased depending on the direction of the DC field

An optical fiber cable laid underground has developed a discontinuity at a distance d from the source end. The fault can be located using the instrument  (a) Optical spectrum Analyzer (OSA) (b) Optical Time Domain Reflectometer (OTDR) (c) Optical Power Meter (OPM) (d) Laser Diffractometer (LD)

Choose the correct statement  (a) Digital multimeters are built using current measuring elements, while analog multimeters are built using voltage measuring units (b) Digital multimeters are built using voltage measuring units, while analog multimeters are built using current measuring units (c) Both digital and analog multimeters are built using voltage measuring units (d) Both digital and analog multimeters are built using current measuring units

Which code is used in constructing k-maps?  A) Hamming code B) 2 out of 5 code C) BCD code D) Gray code

What will happen if a voltmeter is connected like an ammeter in series of the load ? (a) The meter will burn out. (b) The measurement will be too high. (c) The same current will flow as would have been with ammeter in circuit. (d) There will be almost no current in the circuit.

Which of the following will happen if a voltmeter is connected like an ammeter in series to the load ? (A) There will be almost no current in the circuit. (B) The meter will burn. (C) The measurement will be trio high. (D)  A very high current will flow.

To distinguish between signals having very close values, we need an instrument with  (a) high accuracy (b) high resolution (c) high sensitivity (d) high linearity

A piezo-electric type pressure sensor has a sensitivity of 1 mV/kPa and a bandwidth of 300 Hz to 300 kHz. For a constant (dc) pressure of 100 kPa, the steady state output of the sensor in millivolt is (A) 0 (B) 2 (C) 4 (D) 6

Which of the following instrument can be used for measuring speed of an aeroplane ? (A) orifice plate (B) hot wire anemometer (C) rotameter (D) pitot tube

A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the input code 1010:  (1) 0.3125 V (2) 3.125 V (3) 0.78125 V (4) –3.125 V

A peak reading voltmeter has been calibrated with a sine wave signal and scaled in rms volts. If a square wave signal ± 1V peak is applied, the meter reading will be (a) 0.555 V (b) 0.707 V (c) 1 V (d) 1.75 V

The change in value of an analog signal during the conversion process produces what is called the : -  a) quantization error b) resolution error c) Nyquist error d) sampling error

Explain the basic operation of an oscilloscope with necessary diagram for each section in detail.

If the range of an analog transducer is 0 to 10 V, then for a resolution of 5 mV, the bits of ADC will be _____.

When measuring insulation resistance of cables using d.c. source, the galvanometer used should be initially short circuited because  (A) Cables have a low value of capacitance which draws a high value of charging current (B) Cables have a low value of initial resistance (C) Cables have a high value of capacitance which draws a high value of charging current (D) Cables have a low value of capacitance and initial resistance

A 1mA D' Arsonval movement has resistance of 100 Ω. It is to be converted to a 10 V voltmeter. The value of multiplier resistance is  (A) 999 Ω (B) 9999 Ω (C) 9900 Ω (D) 990 Ω

A 0 to 300V voltmeter has a guaranteed accuracy of 1% of full scale reading. The voltage measured by the instrument is 83V. The percentage limiting error is

A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the resolution of the instrument will be (a) 100 mV (b) 99 mV (c) 9 mV (d) 1 mV

The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating anode voltage is reduced to half of its previous value. Then, the vertical deflection of the beam on the screen would become (A) 64 mm (B) 32 mm (C) 8 mm (D) 1 mm

Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply. The potential difference across 60 watt lamp will be: A) 195 volt B) 220 volt C) 245 volt D) 440 volt

Give the classification of the errors used in measuring instrument & state the reason for their occurrence.

The percentage limiting error, in the case of an instrument reading of 8.3V with a 0 to 150V voltmeter having a guaranteed accuracy of 1% full-scale reading is

For an analog PLL, under perfect locking condition, the phase difference (in degrees) between input signal and VCO output should be  A) 0 B) 90 C) 120 D) 180