# Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of

11 views
Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is

(A)sinusoidal (B) square (C) rectangular (D) triangular

Weins bridge is used for measurement of frequency in the applied voltage waveform is measurement of frequency in the applied voltage waveform is sinusoidal

## Related questions

For measurement of low resistance, the bridge used is (a) Wheatstone (b) Kelvin (c) Maxwell (d) Anderson

For measurement of radio frequency ac signals __________ type meter is used

If the voltage applied across a capacitor is triangular in waveform, the waveform of the current is (a) Triangular (b) Rectangular (c) Sinusoidal (d) Trapezoidal

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

For given applied voltage, with the increase in frequency of the applied voltage?

Maxwell's inductance - capacitance bridge is used for measurement of Inductance of: -  a) Low Q coils b) Medium Q coils c) High Q coils d) Low and medium Q coils

Assertion (A) : Wein bridge oscillator is generally used as a variable audio frequency oscillator Reason (R) : by using either capacitor (or) resistor in one of the arms of the bridge, the frequency of a wein bridge oscillator can be varied (A) Both (A) & (R) are true & (R) is correct explanation of (A) (B) Both (A) & (R) are true but (R) is not the correct explanation of (R). (C) (A) is true but (R) is false (D) (A) is false but (R) is true

The Maxwell bridge is used for measuring (a) Capacitance (b) Dielectric loss (c) Inductance (d) Phase angle

The bridge method commonly used for finding mutual inductance is (A) Heaviside Campbell bridge (B) Schering bridge (C) De Sauty bridge (D) Wien bridge

Clamp on ammeter is used for measurement of:

Which of the following instruments can be used for measurement of very high value resistances such as insulation resistance in industries? A) Wheatstone bridge B) Megger C) Ohm-meter D) Resistive potentiometer

The bridge most suited for accurate measurement of relative permittivity of dielectric materials is (A) Carey Foster Bridge (B) Anderson’s bridge (C) Heaviside Bridge modified by Campbell. (D) Schering Bridge.

The best method for measurement of temperatures of hot bodies radiating energy in the visible spectrum is (a) bolometer (b) optical pyrometer (c) thermocouple (d) thermopile

The SCR would be turned OFF by voltage reversal of applied anode-cathode ac supply frequency of A) 10 kHz B) 10 Hz C) 5 kHz D) 5 Hz

The bridge used to measure the dielectric loss of an insulator is: A) Anderson bridge B) Wien’s bridge C) Schering bridge D) Any of the above

A dummy strain gage is used in a quarter bridge strain gage circuit to :  (A) compensate for changes in temperature and lead wire resistance  (B) produce more output voltage from the bridge  (C) increase the sensitivity of the bridge  (D) compensate lead wire resistance only

In a digital voltmeter, the oscillator frequency is 400 kHz, the ramp voltage falls from 8V to 0V in 20 m sec. The number of pulses counted by the counter is (a) 800 (b) 2000 (c) 4000 (d) 8000

In the snubber circuit used in a thyristor to limit the peak voltage overshoot applied across it damping ratio is taken as about  A) 0.14 B) 0.21 C) 0.36 D) 0.62

The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ. The frequency of the signal at Q is A) 10 KHz B) 2.5 KHz C) 20 KHz D) 5 KHz

Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform.

In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

The type of instruments used mainly for standardizing instruments in laboratories is (a) Indicating instrument (b) Integrating instrument (c) Absolute instrument (d) Recording instrument

The LVDT is used for the measurement of (a) voltage (b) force (c) pressure (d) displacement

Hay bridge is suitable for measuring following type of inductance (a) having Q greater than 10. (b) having Q less than 10. (c) having any value of Q. (d) having phase angle of reactance very large.

An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be  (1) unaffected (2) decreased (3) increased (4) either decreased or increased depending on the direction of the DC field

Integrating principle in the digital measurement is the conversion of   (a) Voltage to time (b) Voltage to frequency (c) Voltage to current (d) Current to voltage

For power measurement of three phase circuit by two wattmeter method, when the value of power factor is less than 0.5 lagging:

The Ku frequency band used in satellite communication (for uplink and downlink) is: (1) 14 GHz and 11 GHz (2) 30 GHz and 20 GHz (3) 70 GHz and 50 GHz (4) 60 GHz and 45 GHz

In a standard multimeter for measuring AC voltage, parameter of _____ voltage is measured

A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______ A) DC voltage restorer B) Clamping circuit C) Both A and B D) None of these

For a waveform to be expressed in Fourier series, which of the following conditions must be satisfied? I. Maxwell’s conditions, II. Drichlet conditions, III. Sampling Theorem A) I only B) II only C) II and III only D) I, II and III