Can you help by answering this question?

Composition is a stronger form of which of the following?

5 views
in Mechanical Engineering by
Linde welding uses

1.Neutral flame and rightward technique

2.Carburizing flame and rightward technique

3.Neutral flame and leftward technique

4.Oxidizing flame and leftward technique

1 Answer

0 votes
by

Linde welding uses Carburizing flame and rightward technique

Related questions

1 answer 5 views

Welding of glass is done by 1. Ultrasonic welding 2. Electron beam welding 3. Laser beam welding 4. Explosive welding

asked May 17, 2018 in Mechanical Engineering by Shimroz123
1 answer 23 views

The electrode rod used for welding uses a coating on it 

asked Apr 29, 2018 in Utilization of electrical energy by Shimroz123
1 answer 8 views

Arc welding uses following electric supply (A) ac (B) dc (C) both ac and dc (D) spiral waveform 

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 12 views

The most suitable refrigerant for a commercial ice plant is : (A) brine (B) NH3 (C) Freon (D) air

asked Jun 15, 2018 in Mechanical Engineering by Shimroz123
1 answer 12 views

Dew point temperature is constant as long as there is : (A) no change in moisture content of the air (B) no change in volume of air (C) no change in dry bulb and wet bulb temperature (D) no change in relative and specific humidity of air

asked Jun 15, 2018 in Mechanical Engineering by Shimroz123
1 answer 8 views

The comfort conditions in air conditioning are : (A) 22 ºC dry bulb temperature and 60% relative humidity (B) 25 ºC dry bulb temperature and 100% relative humidity (C) 20º C dry bulb temperature and 75% relative humidity (D) 15º C bulb temperature and 80% relative humidity

asked Jun 15, 2018 in Mechanical Engineering by Shimroz123
1 answer 8 views

Air is normally dehumidified by : (A) injecting water (B) passing steam (C) heating (D) cooling

asked Jun 15, 2018 in Mechanical Engineering by Shimroz123
1 answer 15 views

A fluid in equilibrium cannot sustain : (A) tensile stress (B) compressive stress (C) shear stress (D) bending stress

asked Jun 15, 2018 in Mechanical Engineering by Shimroz123
1 answer 31 views

Which of the following instrument can be used for measuring speed of an aeroplane ? (A) orifice plate (B) hot wire anemometer (C) rotameter (D) pitot tube

asked Jun 15, 2018 in Mechanical Engineering by Shimroz123
1 answer 13 views

Euler’s dimensionless number relates the following : (A) Inertial force and gravity (B) Viscous force and Inertial force (C) Pressure force and Inertial force (D) Pressure force and viscous force

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 13 views

Power transmitted through a pipe is maximum when the loss of head due to friction is : (A) one-half of the total head supplied (B) one-third of the total head supplied (C) one-fourth of the total head supplied (D) zero

asked Jun 14, 2018 in Mechanical Engineering by Quiz
1 answer 8 views

The efficiency of a centrifugal pump is maximum when its blades are : (A) straight (B) bent forward (C) bent backward (D) bent forward first and then backward

asked Jun 14, 2018 in Mechanical Engineering by Quiz
1 answer 42 views

 In axial flow fans and turbines, fluid enters and leaves as follows : (A) radially, axially (B) axially, radially (C) axially, axially (D) radially, radially

asked Jun 14, 2018 in Mechanical Engineering by Quiz
1 answer 17 views

Military type of organisation is known as : (A) line organisation (B) functional organisation (C) line and staff organisation (D) line, staff and functional organisation 

asked Jun 14, 2018 in Mechanical Engineering by Quiz
1 answer 16 views

A systematic job improvement sequence will consist of : (A) motion study (B) time study (C) job enrichment (D) all of these

asked Jun 14, 2018 in Mechanical Engineering by Quiz
1 answer 16 views

Production cost refers to prime cost plus : (A) factory overheads (B) factory and administration overheads (C) factory, administration and sales overheads (D) factory, administration, sales overheads and profit

asked Jun 14, 2018 in Mechanical Engineering by Quiz
1 answer 17 views

In inventory control theory, the economic order quantity is : (A) average level of inventory (B) optimum lot size (C) capacity of a warehouse (D) lost size corresponding to break-even analysis

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 14 views

In value engineering, the term value refers to : (A) manufacturing cost of the product (B) selling price of the product (C) total cost of the product (D) utility of the product

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 17 views

The main object of scientific layout is : (A) to produce better quality of product (B) to utilise maximum floor area (C) to minimise production delays (D) all of these

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 10 views

Gantt chart is used for : (A) inventory control (B) material handling (C) production schedule (D) machine repair schedules

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 8 views

 A twist drill is a : (A) side cutting tool (B) front cutting tool (C) end cutting tool (D) none of these

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 7 views

Tool life is most affected by : (A) cutting speed (B) tool geometry (C) feed and depth (D) microstructure of material being cut

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 50 views

The usual ratio of forward and return stroke in shaper is : (A) 2:1 (B) 1:2 (C) 2:3 (D) 3:2

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 8 views

Binding material used in cemented carbide tools is : (A) Nickel (B) Cobalt (C) Chromium (D) Silicon

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 11 views

Angle between the shear plane and work surface is known as : (A) lip angle (B) rake angle (C) cutting angle (D) shear angle

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 30 views

Material having highest cutting speed is : (A) Cast iron (B) Bronze (C) Aluminium (D) High carbon steel

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 23 views

If the rotating mass of a rim type flywheel is distributed on another rim type flywheel whose mean radius is half the mean radius of the former, then the energy stored in the latter at the same speed will be : (A) Four times the first one (B) Same at the first one (C) One fourth of the first one (D) One and half times the first one

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 54 views

 In a clock mechanism, the gear train used to connect minute hand to hour hand, is : (A) Epicyclic gear train (B) Reverted gear train (C) Compound gear train (D) Simple gear train

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 12 views

The train value of a gear train is : (A) equal to velocity ratio (B) reciprocal of velocity ratio (C) always greater than unity (D) none of the above

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 13 views

The ratio of maximum displacement of the forced vibration to the deflection due to static force is known as : (A) Damping Factor (B) Damping Coefficient (C) Logarithmic Decrement (D) Magnification Factor

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 12 views

If a shaft made of ductile material is subjected to combined bending and twisting moments, calculation based on which one of the following theories would give the most conservative values ? (A) Maximum principle stress theory (B) Maximum shear stress theory (C) Maximum strain energy theory (D) Maximum distortion energy theory

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 17 views

Two metallic blocks having masses in the ratio 2:3 are made to slide down a frictionless inclined plane starting from rest position. When the blocks reach the bottom of the inclined plane, they will have their kinetic energies in the ratio : (A) 2:3 (B) 3:5 (C) 3:2 (D) 7:4

asked Jun 14, 2018 in Mechanical Engineering by Shimroz123
1 answer 10 views

A casting defect which occurs near the ingates as rough lumps on the surface of a casting is known as 1. Shift 2. Sand wash 3. Swell 4. Scab

asked May 17, 2018 in Mechanical Engineering by Shimroz123
1 answer 18 views

The property of sand due to which the sand grains stick together, is called 1. Collapsibility 2. Permeability 3. Cohesiveness 4. Adhesiveness

asked May 17, 2018 in Mechanical Engineering by Shimroz123
1 answer 12 views

In die casting, machining allowance is 1. Small 2. Large 3. Very large 4. Not provided

asked May 17, 2018 in Mechanical Engineering by Shimroz123
1 answer 15 views

The mode of deformation of the metal during spinning is 1.Bending 2.Stretching 3.Bending and stretching 4.Rolling and stretching

asked May 17, 2018 in Mechanical Engineering by Shimroz123
1 answer 15 views

Structural sections such as rails, angles, I-beams are made by 1. Hot rolling 2. Hot drawing 3. Hot piercing 4. Hot extrusion

asked May 17, 2018 in Mechanical Engineering by Shimroz123
1 answer 12 views

The process extensively used for making bolts and nuts is 1. Hot piercing 2. Extrusion 3. Cold peening 4. Cold heading

asked May 17, 2018 in Mechanical Engineering by Shimroz123
1 answer 8 views

The cold chisels are made by 1. Drawing 2. Rolling 3. Forging 4. Piercing

asked May 17, 2018 in Mechanical Engineering by Shimroz123
1 answer 17 views

What are the uses of Thermistors ?

asked Jul 2 by Shimroz123
0 answers 49 views
asked Jan 3 by Nick
2 answers 29 views

 Justify the use of saturable reactor to control the magnitude of welding current.

asked Oct 13, 2018 in Industry Electrical Systems-II by Shimroz123
1 answer 21 views

State four advantages of seam welding over spot welding.

asked Oct 13, 2018 in Industry Electrical Systems-II by Shimroz123
1 answer 20 views

Explain with the diagram butt welding. State its applications. 

asked Oct 12, 2018 in Industry Electrical Systems-II by Shimroz123
2 answers 48 views

State any factors to be considered while selecting electrical welding system.

asked Oct 12, 2018 in Industry Electrical Systems-II by Shimroz123
1 answer 24 views

Give classification of electrical welding.

asked Oct 12, 2018 in Industry Electrical Systems-II by Shimroz123
1 answer 14 views

Compare between Resistance welding and Arc welding on any six points.

asked Oct 12, 2018 in Industry Electrical Systems-II by Shimroz123
1 answer 22 views

Describe with neat sketch operation of seam type resistance welding.

asked Oct 12, 2018 in Industry Electrical Systems-II by Shimroz123
1 answer 36 views

Compare DC and AC welding on any four points.

asked Oct 10, 2018 in Industry Electrical Systems-II by Shimroz123
1 answer 23 views

State the various types of welding.

asked Oct 9, 2018 in Industry Electrical Systems-II by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units
...