Can you help by answering this question?

Describe a simple way of building a simple amplifier?

10 views
in Power Electronics by
A Darlington transistor connection provides a transistor having a very large 

a. Current gain b. Voltage gain c. Impedance gain d. Impedance matching gain

1 Answer

0 votes
by

A Darlington transistor connection provides a transistor having a very large Current gain

Related questions

1 answer 7 views

Darlington pair  1.is a three terminal device with very high current gain 2.has a very high input impedance 3.has a very low output 4.all the above are true 

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 12 views

A semiconductor device made out of a material having very high temperature coefficient of resistance is

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 11 views

In a particular circuit connection, AWG 18 wire is selected over AWG 22. The reason is that it is having

asked May 14, 2018 in Digital Instrumentation by Shimroz123
1 answer 38 views

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

asked Apr 28, 2018 in Power Electronics by Shimroz123
1 answer 7 views

To distinguish between signals having very close values, we need an instrument with  (a) high accuracy (b) high resolution (c) high sensitivity (d) high linearity

asked May 15, 2018 in Digital Instrumentation by Shimroz123
0 answers 14 views

The power loss in a transistor is a function of the product of (A) base current and collector-emitter voltage (B) collector current and base current (C) collector current and saturation voltage (D) collector current and collector-emitter voltage 

asked Jun 4, 2018 in Power Electronics by Shimroz123
1 answer 14 views

The 'h' parameter equivalent circuit of a junction transistor is valid for   (A) High frequency, large signal operation (B) High frequency, small signal operation (C) Low frequency, large signal operation.

asked May 17, 2018 in Power Electronics by Shimroz123
1 answer 21 views

A FET is preferred over an ordinary transistor because it  1. Permits high degree of isolation between input & output circuits 2. Has low noise level 3. Has very high power gain 4. Has all the above properties 

asked May 13, 2018 in Power Electronics by Shimroz123
1 answer 9 views

When an NPN transistor is properly biased then most of the electrons from the emitter   (A) recombine with holes in the base (B) recombine in the emitter itself (C) pass through the base to the collector (D) are stopped by the junction barrier

asked May 17, 2018 in Power Electronics by Shimroz123
1 answer 18 views

Which of the following statements is wrong for transistor biasing methods:  1. The base resistor method does not provide stabilization of operating point 2. The biasing with feedback resistor provides only some stabilization 3. Base resistor method provides better stabilization than collector feedback method 4.Voltage divider bias is widely used because it has stable operating point

asked May 13, 2018 in Power Electronics by Shimroz123
0 answers 18 views

Piezo-electricity provides with a means of converting (a) Electrical to Mechanical (b) Mechanical to Electrical (c) Electrical to Magnetic (d) Magnetic to Electrical

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
1 answer 19 views

Filters with the ___ characteristic are useful when a rapid roll-off is required because it provides a roll-off rate greater than –20/dB/decade/pole:  (1) Butterworth (2) Chebyshev (3) Bessel (4) Elliptical 

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
0 answers 44 views

Darlington pair amplifier refers to cascaded combination of  A) Two common collectors B) Common collector and common emitter C) Common Base and Common emitter D) None of the above

asked Apr 9, 2018 in Electronics Engineering by Shimroz123
1 answer 18 views

A very thin deposit of metal is called as

asked May 15, 2018 in Electrical Engineering by Shimroz123
1 answer 8 views

Materials, whose resistivity at very low temperatures plunges from a finite value to zero and remains there upon further cooling, are known as

asked Apr 23, 2018 in Electrical Engineering by Shimroz123
1 answer 48 views

At very low frequencies a series R-C circuit behaves as almost purely?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

The bundled conductor in EHV transmission line system provides (a) increased inductance (b) reduced capacitance (c) increased capacitance (d) increased voltage gradient

asked May 26, 2018 in Electric Power Transmission by Shimroz123
1 answer 15 views

In practice, a current source inverter consists of an AC/ DC converter with a large inductance ‘L’ in the output. This inductance maintains a ……… …………through the switching devices over short interval of time. A) constant current B) constant voltage C) constant power D) none of the (A), (B), (C)

asked Jun 17, 2018 in Electrical Engineering by Shimroz123
1 answer 21 views

A large hydropower station has a head of 324 metre and an average flow of 1370 metre3 / second. The available hydraulic power from this station will be: A) 4.35 MW B) 4.15 MW C) 4.47 MW D) 4.73 MW

asked Jun 4, 2018 in Electric Power Generation by Shimroz123
1 answer 21 views

 A coil with large distributed capacitance has _____.

asked May 29, 2018 in Capacitance by Shimroz123
1 answer 19 views

A loss of excitation protection scheme for large generating unit employs A) under frequency relays B) offset Mho relay C) reactance relay D) percentage differential relay

asked May 24, 2018 in Switchgear And Protection by Shimroz123
1 answer 4 views

When a large flat surface in electroplated,

asked May 15, 2018 in Electrical Engineering by Shimroz123
1 answer 32 views

A large AC generator, supplying power to an infinite bus, has a sudden short-circuit occurring at its terminals. Assuming the prime mover input and the voltage behind the transient reactance to remain constant immediately after the fault, acceleration of the generator rotor is

asked Apr 29, 2018 in Power system by Shimroz123
1 answer 33 views

A large dc motor is required to control the speed of the blower from a 3 -phase ac source. The suitable ac to dc converter is, 3 -phase (a) Fully controlled bridge converter (b) Fully controlled bridge converter with freewheeling diode (c) Half controlled bridge converter (d) Converter pair in sequence control

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

Consider the following statements with regard to a GTO : 1. The turn-off gain of the GTO is large. 2. Large negative gate current pulses are required to turn off the GTO. 3. GTO has large reverse blocking capability. Which of the above statements is/are correct ? (a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3

asked Apr 25, 2018 in Electrical Engineering by Shimroz123
0 answers 8 views

The dielectric strength of ferromagnetic materials depends to a large extent on (a) Intensity of electric field (b) Presence of magnetic materials in vicinity (c) Area of hysterisis loop for materials (d) Frequency of applied voltage

asked Apr 14, 2018 in Electrical Engineering by Shimroz123
0 answers 27 views

A synchronous machine with large SCR has (1) Poor voltage regulation (2) Poor stability (3) Low short circuit current (4) More synchronizing power

asked Apr 11, 2018 in Electrical Engineering by Shimroz123
1 answer 15 views

The input voltage to an OP AMP is a large voltage step. The output is an exponential waveform that changes to 0.25 V in 0.1µs (microsecond). The slew rate of the OP AMP is : -  a) 5V/µs b) 2.5 V/ µs c) 3V/µs d) 4.5V/ µs

asked Apr 10, 2018 in Instrumentation and control by Shimroz123
0 answers 19 views

A large size synchronous generator is protected against overloads by   (a) over current relay (b) mho relay (c) temperature sensitive relay (d) Buchholz relay

asked Apr 10, 2018 in Electrical Engineering by Shimroz123
0 answers 21 views

A large transformer operating at no load draws an exciting current Io of 5A, when the primary is connected to a 120 V, 60 Hz source. From a wattmeter test, it is known that iron losses are equal to 180 W. Calculate the reactive power absorbed by the core.  (A) 600 var (B) 572 var (C) 180 var (D) 360 var 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
1 answer 20 views

The substances which have a large number of free electrons and offer a low resistance are called?

asked Mar 25, 2018 in Basic concepts by Shimroz123
1 answer 22 views

If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be?

asked Mar 25, 2018 in Electrical Engineering by Shimroz123
2 answers 72 views

State what is the significance of conducting phasing out test on a 3-phase transformer? Explain its procedure with a suitable connection diagram.

asked Sep 15, 2018 by Shimroz123
1 answer 19 views

Which three-phase connection can be used in a transformer to introduce a phase difference of 30o between its output and corresponding input line voltages  (A) Star-Star (B) Star-Delta (C) Delta-Delta (D) Delta-Zigzag

asked May 17, 2018 in Transformer by Shimroz123
1 answer 14 views

The line voltage EL in a star connection is equal to.... (Ep = phase voltage)

asked May 15, 2018 in Electrical Engineering by Shimroz123
1 answer 13 views

AT-T connection has higher ratio of utilizax that n a V - V connection only when  1. Identical transformers are used  2. Load power factor is leading  3. Load power factor is unity  4. Non-identical transformers are used 

asked May 13, 2018 in Electrical Engineering by Shimroz123
1 answer 14 views

Which of the following 3-phase connection of a transformer causes interference with the neighbouring communication lines:  (A) Delta-Star (B) Star-Delta (C) Delta-Delta (D) Star-Star

asked May 8, 2018 in Electrical Engineering by Shimroz123
1 answer 16 views

If a cell connection is reversed in parallel group, what will happen? A. Open circuit B. All cells will be equally charged C. short circuit D. Nothing will happen 

asked Apr 12, 2018 in Electrical Engineering by Shimroz123
0 answers 16 views

A 3 Phase, 60 Hz generator connected in Y connection, generates a line to line voltage of 23900 V. Calculate the peak line voltage.  (A) 13800 V (B) 33800 V (C) 42300 V (D) 23900 V 

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 29 views

What is the equivalent resistance of one limb A when delta connection is transformed in to star?  (A) R1R3/R1+R2+R3 (B) R2R3/R1+R2+R3 (C) R1R2R3/R1+R2+R3 (D) R1+R2+R3

asked Apr 5, 2018 in Electrical Engineering by Shimroz123
0 answers 65 views

The differential coupling of two coils in series connection has self-inductance of 2 mH & 4 mH & a mutual inductance of 0.15 mH. The equivalent inductance of the combination is:  (A) 5.7 mH (B) 5.85 mH (C) 6 mH (D) 6.15 mH

asked Apr 5, 2018 in Electrical Engineering by Shimroz123

Welcome to electronics2electrical.com here you can ask questions related to electrical, electronics, mechanical, telecommunication, instrumentation, computer, mathematics, physics etc.
Be respectful to all the members. Do not copy and paste the answers from other websites which have copyright content. While asking question give full details about it.

Categories

Most popular tags

power motor dc circuit transformer voltage current used system phase resistance factor synchronous load ac energy induction electric generator series frequency between speed capacitor use electrical meter line difference control type mosfet transmission magnetic plant high single instrument bjt unit source advantages function diode and machine winding field define torque parallel amplifier supply shunt thyristor motors electricity arduino maximum time relay armature problem value on transformers types coil diagram state flow ratio material three formula starting direction theorem method emf operating efficiency digital wave microprocessor test instruments inductance loss measure operation connected signal low applications effect single-phase network temperature working constant losses different law wattmeter measuring compare controlled breaker drive device logic rc full switch flux wire resistivity disadvantages free of materials machines angle force converter conductor transistor gain open protection scr core measurement number bridge principle generators reactance circuits negative the friction iron loop short pole battery conservation steam resistors hysteresis computer using analog lines secondary station gate a rectifier inverter linear induced relays nuclear capacitance basic characteristics design direct work rotor electronics ammeter forces diesel damping rlc connection factors capacitors minimum insulation moving regulation running self systems air fault range main stability quality starter igbt eddy alternator ideal rl average 3-phase plants arc thermal error fuzzy biasing dielectric pressure balanced superposition errors copper rotation feedback impedance measured electronic electrons charge inductive transfer explain start off back curve over solar is three-phase tariff locomotive peak bias zener engineering commutator surge conductors rating universal potentiometer density permanent mechanical transducer capacity memory adc excitation two fuse pure harmonics application semiconductor inductor internal pmmc reaction welding resonance traction permeability breakers rms designed electromagnetic si generation brushes switching capacitive shaded rate 1 distribution resistor methods delta star oscillator reluctance simplification algebra 8085 boolean weston dynamometer insulating strength installation definition fuel heating earth units

8,450 questions

7,047 answers

132 comments

3,085 users

...